BURKS 10GA5-1 1/4AB, Centrifugal Pump 1HP 115/230v All BRONZE Construction. Close Coupled to a 1 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.13 Inches.

BURKS 7G5-1 1/4, CENTRIFUGAL PUMP 1PH 3/4HP 115/230V Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4 Inches.

BURKS 30WA6, Centrifugal Pump 115/230v 3HP Burks 30WA6 Centrifugal Pump, Self Priming, 60 Hz, Single Phase, 3500 RPM, 3 Horsepower, ODP Motor Enclosure. Close Coupled to a 3 Horsepower 115/230 Volts motor Bronze Fitted Cast Iron Construction w/ Plastic Impeller. Ports are 1-1/2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet.   Please contact us for a shipping quote at http://www.clrmarine.com/Contact_Us   

BURKS 5CT7M, TURBINE PUMP 1/2HP 1PH 115/230V Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   FEATURES Cast Iron/Bronze/ Stainless Steel construction Low Flow - High Pressure   FOUR POSITION CASING Discharge can be located in any of four positions. Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates the need to disturb piping should the pump ever require service - the casing stays in the line.   ENCLOSED BRONZE IMPELLER Of the latest hydraulic design for maximum efficiency, impeller is balanced for vibration-free operation and threaded onto stainless steel motor shaft.   ENCLOSED GLASS FILLED NORYL® IMPELLER Of the latest hydraulic design for maximum efficiency, impeller has molded in brass insert threaded onto stainless steel motor shaft. *Noryl® Impeller is not designed for use with hydrocarbons.   MECHANICAL SHAFT SEAL Standard self-adjusting shaft seal for temperatures to 225°F (107°C) and pressures to 150 psi (1034 kpa). Ceramic seat and carbon seal face for long trouble-free service. Special seals are available for higher temperatures and fluids other than water.   MOTORS Standard pump motors are of open drip proof (ODP) construction and are rated with jet pump service factors for continuous duty operation. Motors are 56 frame size with NEMA standard mounting flange, one piece threaded stainless steel shaft and ball/ball bearing construction.   FACTORY TESTED After careful assembly and inspection, EVERY pump is factory tested and meets Hydraulic Institute standards.   UNSPSC Code: 40150000

BURKS 7CT5M, Turbine Pump 3/4HP 1PH 115/230v Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 7CT6M, TURBINE PUMP 3/4HP 1PH 115/230v Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 7CT7M, PUMP 3/4HP 1PH 115/230v Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 3CT5M, Turbine Pump 1/3HP 1PH 115/230 volt Bronze Fitted Cast Iron Construction. Close Coupled to a 1/3 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 5CT5M, TURBINE PUMP 115/230V 1/2HP 1PH Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

March Mag-Drive Centrifugal Pump Plastic 230V Hi Speed  Beer Pump The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   Unit System 60Hz 50Hz Max Flow 6 GPM 18.9 LPM Max Head 12.1 FT 2.5 M Power .04 HP .029 KW Electrical 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller) Can handle liquids of 250F Materials are FDA Food Compliant With 6 Foot Cord and Plug Components are UL Recognized American Made          

BURKS 15WA6, Centrifugal Pump Self Priming 115/230v Bronze Fitted Cast Iron Construction w/ Plastic Impeller. Close Coupled to a 1-1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet.

BURKS 5G5-1 1/4, Centrifugal Pump 115/230v 1PH 1/2HP Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 3.63 Inches.   UNSPSC Code: 40150000

BURKS 5GV6-1 1/4FC, Centrifugal Pump 115/230v 1PH 1/2HP Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are Square Mouth Flanged Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 3.63 Inches.   UNSPSC Code: 40150000

BURKS 7WT5, PUMP SELF PRIME 115/230v 1PH 3/4HP Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 2 Inches NPT Inlet, 2 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 10CS5M, Turbine Pump 32.5 gpm 115/230v Burks close coupled 32.5 gpm turbine pump having 1-1/4" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1 hp power rating.   Burks exclusive unique regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. Compact space saving size No coupling - eliminates misalignment problems Dependable carbon ceramic mechanical shaft seal for temperatures to 225 deg F (107 deg C) Bronze impeller with monel blades - the only moving part Bronze raceway with cast-in vortex pockets - will not vapor lock 303 stainless steel pump shaft Easy to service Every pump factory tested