|
BURKS 5CT5M, TURBINE PUMP 115/230V 1/2HP 1PH
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
1978.20 |
|
|
BURKS 5CT6M, TURBINE PUMP 115/230V 1/2HP 1PH
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
1978.20 |
|
|
BURKS 3CR6M-V, Turbine Pump 1/3HP 1PH 230V Viton
Turbine Pump and Motor unit.
Bronze Fitted Cast Iron Construction w/ Viton seal & O-Ring.
Close Coupled to a 1/3 Horsepower, 3450 RPM, 230 Volts, 1 Phase Motor.
Ports are 1/2 Inches NPT Inlet, 1/2 Inches NPT Outlet.
UNSPSC Code: 40150000
|
1762.20 |
|
|
BURKS 320CS6M, TURBINE PUMP 230/460V 3PH 2HP
Bronze Fitted Cast Iron Construction.
Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
Please Contact us for a shipping quote http://www.clrmarine.com/Contact_Us
|
3085.16 |
|
|
BURKS 320CS7M, TURBINE PUMP 230/460v 3PH 2HP
All BRONZE Construction.
Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
Please Contact us for a shipping quote http://www.clrmarine.com/Contact_Us
|
3085.16 |
|
|
BURKS T320CS7M, TURBINE PUMP 2HP 60 VOLT 3PH
Bronze Fitted Cast Iron Construction.
Close Coupled to a 2 Horsepower , 3450 RPM, 208-230/460 HZ , 60 Volt, 3 Phase, TEFC Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
3402.56 |
|
|
BURKS 5WT5, PUMP SELF PRIME 115/230v 1PH 1/2HP
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 2 Inches NPT Inlet, 2 Inches NPT Outlet.
|
1844.10 |
|
|
BURKS 315CS5M, TURBINE PUMP 230/460V 1.5HP
Bronze Fitted Cast Iron Construction.
Close Coupled to a 11/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2882.48 |
|
|
BURKS 24CT6M, Turbine Pump 115/230v 1"Ports
Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/4 Horsepower, 1750 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2118.60 |
|
|
BURKS 310CS6M, TURBINE PUMP 1 HP 3 PH 230/460 volts
Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction.
Close Coupled to a 1 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2407.24 |
|
|
BURKS 15CS5M, Turbine Pump Close Coupled 115/230v
Bronze Fitted Cast Iron Construction. Close Coupled to a 1.5 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2820.38 |
|
|
BURKS 15CS6M, Turbine Pump 1.5HP 115/230v
Bronze Fitted Cast Iron Construction. Close Coupled to a 1-1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2820.38 |
|
|
BURKS 20CS6M Close Coupled Turbine Pump
BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.
BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.
Self-Priming Pump
Compact and Space-saving size
No coupling so this eliminates misalignment problems
Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C).
Bronze impeller with Monel blades, therefore the only moving part
Bronze raceway with cast-in vortex pockets – will not vapor lock
#303 Stainless Steel pump shaft
Every pump is factory tested
Motor Information
4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.
CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor
start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.
High Temperature
For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications.
|
3161.06 |
|
|
BURKS 35CT7M, Turbine Pump 230/460v 1PH 1/2HP
Turbine Pump and Motor unit.
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
1978.20 |
|
|
BURKS 5CT7M, TURBINE PUMP 1/2HP 1PH 115/230V
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
FEATURES
Cast Iron/Bronze/ Stainless Steel construction
Low Flow - High Pressure
FOUR POSITION CASING
Discharge can be located in any of four positions.
Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates the need to disturb piping should the pump ever require service - the casing stays in the line.
ENCLOSED BRONZE IMPELLER
Of the latest hydraulic design for maximum efficiency, impeller is balanced for vibration-free operation and threaded onto stainless steel motor shaft.
ENCLOSED GLASS FILLED NORYL® IMPELLER
Of the latest hydraulic design for maximum efficiency, impeller has molded in brass insert threaded onto stainless steel motor shaft. *Noryl® Impeller is not designed for use with hydrocarbons.
MECHANICAL SHAFT SEAL
Standard self-adjusting shaft seal for temperatures to 225°F (107°C) and pressures to 150 psi (1034 kpa).
Ceramic seat and carbon seal face for long trouble-free service.
Special seals are available for higher temperatures and fluids other than water.
MOTORS
Standard pump motors are of open drip proof (ODP) construction and are rated with jet pump service factors for continuous duty operation. Motors are 56 frame size with NEMA standard mounting flange, one piece threaded stainless steel shaft and ball/ball bearing construction.
FACTORY TESTED
After careful assembly and inspection, EVERY pump is factory tested and meets Hydraulic Institute standards.
UNSPSC Code: 40150000
|
2069.10 |
|