BURKS 5CT6M, TURBINE PUMP 115/230V 1/2HP 1PH Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 5CT6M-FE, TURBINE PUMP 115/230V 1PH 1/2HP BF Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower , 3450 RPM, 115/230 HZ , 60 Volt, 1 Phase, ODP Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

Burks 5CT7MAB, Turbine Pump 115/230v 1Ph 1/2Hp All BRONZE Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS A3CR6M, Turbine Pump 4 gpm 230v Application: Carpet Cleaning Machines, Small Steam Generators, Solar Heating Systems, Booster Pump, Injector Venturi Operation, Cleaning and Flushing   Frame/Raceway : Bronze Impeller : Bronze (Monel Blades) Shaft : #316 Stainless Steel Front Cover : Bronze Shaft Seal : Carbon-Ceramic / S. Steel / Buna-N   MAXIMUM OPERATING CONDITIONS TEMPERATURE (For Standard Buna-N Seal) : 225°F (107°C) INLET PRESSURE : 50 PSI (344kpa) CASING WORKING PRESSURE : 150 PSI (1034kpa) VISCOSITY : 200 SSU   FEATURES • Compact Size-Ideal for OEM Applications • All Bronze Construction with Monel Impeller Blades • Carbon/Ceramic Shaft Seal for Temperatures to 225°F (107°C) • #316 Stainless Steel Shaft • Close Coupled Design - No Couplings or Alignment Problems • Motors have ball/ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof. Rated for continuous duty operation at all ratings shown. • Capacitor Start Motors Have Built-In Automatic Overload Protection • Furnished with UL Recongnized Motor Lead • Field Adjustable Impeller for Extented Service Life   Motors have ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof. Compact size: only 10 1/2" long x 4" wide x 6 1/4" high.)   UNSPSC Code: 40150000

BURKS 5G5-1 1/4, Centrifugal Pump 115/230v 1PH 1/2HP Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 3.63 Inches.   UNSPSC Code: 40150000

BURKS 5GV6-1 1/4FC, Centrifugal Pump 115/230v 1PH 1/2HP Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are Square Mouth Flanged Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 3.63 Inches.   UNSPSC Code: 40150000

March TE-5.5C-MD Mag-Drive Centrifugal Pump single phase with 115/230V Motor   Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   The TE-5.5C-MD pumps Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Nitric Acid, Phosphoric Acid, Potassium Chloride, Potassium Hydroxide, Sodium Hydroxide (Caustic Soda), Sodium Chloride, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.   Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V                3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)  

Flojet 04300-531A Mpu 115V S/E Pse Sw40 Flojet 04300531A Self-Priming Quad Diaphragm Pump - 35 PSI, 3.5 GPM, 115 VAC Pump and Electric Motor   Flojet's 04300531A is a quadruple diaphragm pump with a four-piston design that delivers a high flow rate reaching a maximum of 3.5 GPM. Pump self-primes up to 2.4m vertical lift. Pump body is manufactured using polypropylene for its chemical and corrosion resistant properties. Equipped with a 1/2-inch hose barb inlet and a 1/2-inch male Quest outlet. Compatible with 115 VAC electrical connections. Specifications: Voltage: 115 VAC Inlet: 1/2" Hose Barb Outlet: 1/2" Male Quest Flow: 3.5 GPM Max PSI: 35 PSI  Body: Polypropylene] Check Valve: EPDM  Diaphragm: Santoprene Option: Pressure Switch Features: Self-primes up to 2.4m vertical lift Handles Water-Like and Viscous Liquids up to 250 cP Four-piston design delivers higher flow rates Chemical-resistant polypropylene pump head for Iong life Choice of elastomeric materials to work with many chemicals Quick-connect plug-in ports for easy installation Optional pressure-switch control to run the pump only as needed  

AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet Cast Iron base and adapter 1 inch NPT cast iron flanges 304 series stainless steel components with Teflon wear rings EPDM-Tungsten Carbide Seal that is easy to remove and replace The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output.  This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems.  These pumps have NOT been investigated for use in drinking water systems.  

Mate USA M164-300-12 12V GEAR PUMP 10.5 GPM DIESEL FEATURES Pump Body: Nickel Plated Brass Port Size: 3/8" BSP (British) Female Threaded Ports and 3/8" NPT Male Threaded Ports Flow: 10.5 GPM Pressure: 21.8 PSI Gears:Bronze Shaft Seal: Lip Type Shaft: Stainless Steel Motor:12 Volt Heavy Duty Ball Bearing Design  Motors:  ISO 8849 Marine (Bilge Standard) IP Protection 67    APPLICATIONS  Diesel Transfer Refueling Light Weight Oils Fresh Water and Glycol Antifeeze Self-Priming

Mate USA M164-300-13 24V GEAR PUMP 10.5 GPM DIESEL FEATURES Pump Body: Nickel Plated Brass Port Size: 3/8" BSP (British) Female Threaded Ports and 3/8" NPT Male Threaded Ports Flow: 10.5 GPM Pressure: 21.8 PSI Gears:Bronze Shaft Seal: Lip Type Shaft: Stainless Steel Motor:24 Volt Heavy Duty Ball Bearing Design  Motors:  ISO 8849 Marine (Bilge Standard) IP Protection 67    APPLICATIONS  Diesel Transfer Refueling Light Weight Oils  

BURKS 10CS5M, Turbine Pump 32.5 gpm 115/230v Burks close coupled 32.5 gpm turbine pump having 1-1/4" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1 hp power rating.   Burks exclusive unique regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. Compact space saving size No coupling - eliminates misalignment problems Dependable carbon ceramic mechanical shaft seal for temperatures to 225 deg F (107 deg C) Bronze impeller with monel blades - the only moving part Bronze raceway with cast-in vortex pockets - will not vapor lock 303 stainless steel pump shaft Easy to service Every pump factory tested

BURKS 24CT6M, Turbine Pump 115/230v 1"Ports Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 1/4 Horsepower, 1750 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 10CS6M, TURBINE PUMP 115/230v 1PH 1HP BF Close Coupled to a 1 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 20CS6M Close Coupled Turbine Pump BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.   BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.   Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades, therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Every pump is factory tested     Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.     CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature   For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications.