|
BERKELEY M13784, MOTOR BKT MACHINED - SSHM-2
|
583.63 |
|
|
BERKELEY B82456-01, SSHM-2 SERIES PUMP
Berkeley B82456-01 SSHM-2 Series Stainless Steel Centrifugal Pump, 2 HP, 230 Volts, Single Phase, 1-1/2" Suction, 1-1/4" Discharge.
Contact us for shipping cost at www.clrmarine.com/Contact_Us
|
2081.52 |
|
|
BERKELEY 111P2700, O'RING SLEEVE, SSHM-2 4X142
|
5.32 |
|
|
BERKELEY S32016, MECH SHAFT SEAL 2-1/8 TYPE 21
|
1656.48 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor with 96" Leads - 2 Wire, 3-Bolt Mount
Replacement tilt trim motor that will fit BRP-OMC. 2-wire connection, Includes O-ring,3-bolt mount, Male Spade Terminal Ends, 96” Leads
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
BRP-OMC Tilt Trim Motor 391264
BRP-OMC Tilt Trim Motor 393259
BRP-OMC Tilt Trim Motor 393988
BRP-OMC Tilt Trim Motor 395840
BRP-OMC Tilt Trim Motor 434795
BRP-OMC Tilt Trim Motor 983019
BRP-OMC Tilt Trim Motor 983446
BRP-OMC Tilt Trim Motor 985237
SIERRA Tilt Trim Motor 18-6759
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
128.05 |
|
|
Replacement Outboard Tilt Trim Motor - Late Model Mercury, 2-Wire
Replacement outboard tilt trim motor that will fit late model Mercury 135, 150 XR6, Magnum lll, 175, 200, 225, 250 HP, 105-140 HP Jet, 2-wire connection, 2-bolt mount, Includes O-ring, Flat-blade shaft, Bullet Connector Terminal Ends.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 8M0031551
MERCURY Tilt Trim Motor 8M0060140
MERCURY Tilt Trim Motor 828708
MERCURY Tilt Trim Motor 828708T
MERCURY Tilt Trim Motor 878265A1
MERCURY Tilt Trim Motor 878265A4
SIERRA Tilt Trim Motor 18-6773
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
238.67 |
|
|
Cat Pump Motor 1Ph 115/220V 2.5Hp model 8125
Motor made by CAT Pumps for 2SF Pumps. Electric powered motor. Operates using single phase power.
RPM: 1750
Phase: SingleVoltage
AC: 115/230
Shaft Diameter: 5/8 inch
Horsepower: 2.5
|
774.72 |
|
|
Wiper Motor 1000 Series - 12V - 2.5" Shaft - 80°
The 1000 Waterproof Wiper Motor has a fully sealed waterproof housing made of UV stabilized, high-temperature, high-impact thermoplastic. It powers 18" Deluxe arm and 18" Deluxe blade combination at sweep sets of 80 degree or less or 16" Deluxe arm and 16" Deluxe blade combinations at a sweep set of 110 degree.
Features:
Factory pre-set sweep of 80 degree or 110 degree adjustable to 50 degree, 65 degree, 80 degree or 110 degree
0.625" diameter shaft (16 mm)
12 volt heavy-duty motor with anti-rotation drive shaft
Knurled drive shaft and solid brass arm drive nut
Coast to park with adjustable right or left self parking
Retail version includes 5 amp fuse and holder (on/off switch not included)
RF shielded circuitry
Weight: 1.75 lbs
Available in two shaft lengths: 1.5" and 2.5" (includes .5" length of knurled arm fitting)
Measures approximately 6.625" L x 3.375"W x 2" D
Stall torque: 55 in-lbs (63 kgf/cm; 6.2 Nm)
Stall current: 9.8-10.0 amps
No load current: 0.8-1.2 amps+
|
158.58 |
|
|
Wiper Motor 1000 Series - 12V - 2.5" Shaft - 110°
The 1000 Waterproof Wiper Motor has a fully sealed waterproof housing made of UV stabilized, high-temperature, high-impact thermoplastic. It powers 18" Deluxe arm and 18" Deluxe blade combination at sweep sets of 80 degree or less or 16" Deluxe arm and 16" Deluxe blade combinations at a sweep set of 110 degree.
Features:
Factory pre-set sweep of 80 degree or 110 degree adjustable to 50 degree, 65 degree, 80 degree or 110 degree
0.625" diameter shaft (16 mm)
12 volt heavy-duty motor with anti-rotation drive shaft
Knurled drive shaft and solid brass arm drive nut
Coast to park with adjustable right or left self parking
Retail version includes 5 amp fuse and holder (on/off switch not included)
RF shielded circuitry
Weight: 1.75 lbs
Available in two shaft lengths: 1.5" and 2.5" (includes .5" length of knurled arm fitting)
Measures approximately 6.625" L x 3.375"W x 2" D
Stall torque: 55 in-lbs (63 kgf/cm; 6.2 Nm)
Stall current: 9.8-10.0 amps
No load current: 0.8-1.2 amps+
|
158.58 |
|
|
Wiper Motor, 1000 Series, 12V, 2.5" Shaft, 65° Sweep
The 1000 Waterproof Wiper Motor has a fully sealed waterproof housing made of UV stabilized, high-temperature, high-impact thermoplastic. It powers 18" Deluxe arm and 18" Deluxe blade combination at sweep sets of 80 degree or less or 16" Deluxe arm and 16" Deluxe blade combinations at a sweep set of 110 degree.
Features:
Factory pre-set sweep of 80 degree or 110 degree adjustable to 50 degree, 65 degree, 80 degree or 110 degree
0.625" diameter shaft (16 mm)
12 volt heavy-duty motor with anti-rotation drive shaft
Knurled drive shaft and solid brass arm drive nut
Coast to park with adjustable right or left self parking
Retail version includes 5 amp fuse and holder (on/off switch not included)
RF shielded circuitry
Weight: 1.75 lbs
Available in two shaft lengths: 1.5" and 2.5" (includes .5" length of knurled arm fitting)
Measures approximately 6.625" L x 3.375"W x 2" D
Stall torque: 55 in-lbs (63 kgf/cm; 6.2 Nm)
Stall current: 9.8-10.0 amps
No load current: 0.8-1.2 amps
|
132.44 |
|
|
Berkeley S39518 CP High Head
Berkeley S39518 is a high head, series CP, centrifugal pump with a noryl impeller. The CP series pumps have a heavy-duty cast iron construction and feature a heavy-duty motor with easy service design and four-position discharge.
Features
3/4 HP
Motor Voltage: 115/230
Pipe Tapping Sizes: Suction 1-1/4 in, Discharge 1 in.
Drain port provided for easy winterizing
All models include replaceable wear ring and feature back pull-out design for easy serviceability
CP Series with Noryl impellers are abrasion-resistant for normal applications with working temperatures to 140°F
Applications
Water systems and sprinkling for homes, farms and industry
This item has a warranty of 12 months from date of original installation, or 18 months from date of manufacture.
|
1059.84 |
|
|
BERKELEY B85604, IMPELLER REPAIR PART KIT
SSHM2 Pump Model B82456. Includes (4) Impellers, (4) Diffusers, (2) O-Rings, Mechanical Seal and Locknuts.
|
370.37 |
|
|
|
14.45 |
|
|
BERKELEY 121P1710, WASHER SS SEAL RETAINER
|
32.13 |
|
|
BERKELEY 121P1760, SS FLAT WASHER 5/26"
|
10.83 |
|