Digital Duo Charge - 12/24V The Digital Duo Charge (DDC-12/24) provides a “hands off” solution for charging two battery banks without the use of problematic isolators or manual battery switches. During charging the DDC-12/24 monitors voltage at the house battery. When voltage exceeds the set minimum (typically 13.2V in a 12V system and 26.4V in a 24V system) the DDC-12/24 automatically engages, providing up to 30A charge current to the starting battery. When no charge source is present, the DDC-12/24 separates the batteries so the starting battery won’t be accidentally discharged into the house battery. An optional solenoid control enables higher start battery charging output when required. Features: Multi Bank Charging The DDC is a Solid-State Battery Combiner Control Voltage and Current between House and Start Batteries Eliminates the Need for an Isolator, Relay or Manually Operated Battery Switch Used in Concert with Max Charge or ARS-5 Regulators Can also be Employed without a Balmar Regulator Works in Both 12V and 24V Applications House and Start Batteries can be different technologies Start Battery Temperature Sensing Available with the MC-TS-B Sensor Cable 4 Battery Programs Supported for the Start Battery: Standard Flooded, Deep Cycle Flooded, AGM and Gel Cell This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

8121 - 5 Position Contura Switch Panel with Dual USB Chargers - 12/24V DC - Black Designed for open-cockpit and flybridge applications using switches to complement existing controls commonly used on many boats. Features: Includes 12/24V DC, 4.8A Dual USB chargers with intelligent device recognition that maximizes charge rate Designed for 12 or 24V DC systems Watertight mounting gasket ON indicating LEDs embedded in all switches Technical Specifications: Nominal Voltage - 12/24V DC Operating Current - 18mA per switch Switch Rating - 20A@12V and 15A@24V DC USB - 12/24V Dual USB Charger 4.8A  Dimensions (H x W x D) - 7.5" x 5.25" x 3" (190.5 x 133.35 x 76.2mm) In the Box: 8121 Panel Labels Mounting hardware *Sold as Individual 

8421 - 5 Position Contura Switch Panel with Dual USB Chargers - 12/24V DC - White Designed for open-cockpit and flybridge applications using switches to complement existing controls commonly used on many boats. Features: Includes 12/24V DC, 4.8A Dual USB chargers with intelligent device recognition that maximizes charge rate Designed for 12 or 24V DC systems Watertight mounting gasket ON indicating LEDs embedded in all switches Technical Specifications: Nominal Voltage - 12/24V DC Operating Current - 18mA per switch Switch Rating - 20A@12V and 15A@24V DC USB - 12/24V Dual USB Charger 4.8A  Dimensions (H x W x D) - 7.5" x 4.5" x 3.25" (190.5 x 133.35 x 76.2mm) In the Box: 8421 Panel Labels Mounting hardware *Sold as Individual

8521 - 5 Position Contura Switch Panel with Dual USB Chargers - 12/24V DC - Black Designed for open-cockpit and flybridge applications using switches to complement existing controls commonly used on many boats. Features: Includes 12/24V DC, 4.8A Dual USB chargers with intelligent device recognition that maximizes charge rate Designed for 12 or 24V DC systems Watertight mounting gasket ON indicating LEDs embedded in all switches Technical Specifications: Nominal Voltage - 12/24V DC Operating Current - 18mA per switch Switch Rating - 20A@12V and 15A@24V DC USB - 12/24V Dual USB Charger 4.8A  Dimensions (H x W x D) - 7.5" x 4.5" x 3.25" (190.5 x 133.35 x 76.2mm) In the Box: 8521 Panel Labels Mounting hardware *Sold as Individual 

Digital Bilge Switch - 12/24V The 12/24V digital bilge switch activates your bilgepump automatically when water exceeds the acceptable level and deactivate when water has been removed. For a fully automatic removal of your bilge water connect a switch to your electrical bilge pump. Field sensing digital technology, fully sealed without any moving parts. Will not corrode and are not affected by oil or debris. Features: Type: Electronic Switch Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance

Headhunter XRS-124 X-CAL 12/24V Pump X-Caliber – 12-24V DC Water Pressure Pump Quiet, reliable, blasting water pressure. Combining advanced DC motor and control technology with a proven self-priming centrifugal pump, the X-caliber surges past the competition with a flood of features. A built in microprocessor interfaced with a rugged ceramic temperature and pressure sensor provides variable speed operation, prevents dry running damage and ensures complete electrical protection.   Part#Description   XRS-124X-Caliber 12-24 VDC Saltwater Pressure System   Control Panel: Program power and pressure settings via the integrated control panel. Four colored LED’s display current settings and alarm conditions.   Advanced Features: Adjustable cut in pressure Adjustable power setting Operates on 12 or 24VDC Over voltage protection Under voltage protection Over current protection Anti-flooding protection Dry run protection Variable Speed Rotating bracket   Product Details/Specifications:   Liquid Temp 32°F (0°c)-104°F (40°c) Ambient Temp 32°F (0°c)-122°F (50°c) Max Pressure 67 PSI (4.5 bar) Max Flow 10 GPM (38 lpm) Suction/Discharge 3/4” FPT (Optional metric adapter) Weight 16lbs (7.2 kg) Dimensions 15”(382mm)L 8”(203mm)W 7”(178mm)H      

Digtal Voltage Sensing Relay (DVSR) - 12/24V The Digital Voltage Sensing Relay (DVSR) allows the charging of a second battery bank from any single charging source. When the voltage on the charged bank rises sufficiently, the DVSR engages allowing the 2nd battery bank to charge. When charging stops and voltage falls, the DVSR automatically isolates the battery banks, ensuring that engine start batteries are kept fully charged. Digital circuitry provides superior reliability and extremely low power consumption. Digital enhancements have introduced remote sensing circuitry that allows an optional connection from the ignition switch to provide the same functionality as single sense VSR and zero power consumption when engine is off. Another benefit is a zero stand by current draw when remote sensing circuit is utilized with a storage mode switch fitted (switch in open position). Features: Safely charge two or more independent battery banks from one charge source such as an alternator or battery charger Charges engine starting batteries before combining auxiliary bank for charging Protects start batteries from becoming flattened by domestic loads Isolates electronics from harmful electrical surges from starter motors Simple to install 3 wire connection leaves alternator wiring intact No volt drop vs diode isolators Ignition protected Surface or panel mountable Replaces previous models 710-125A and 710-125A-DS Multi voltage, auto selects between 12 and 24V DC operation Digital circuits provide very low power consumption and enhanced performance Remote status LED output option WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flip Pro with Front Fit Bezel 12/24V Fast Charge Dual USB-A/C Socket Ultra-fast USB charging for the next-generation boater.  Flip Pro is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection and the fastest charging for your device onboard. Ultra-fast USB charging for the next-generation boater.  Flip Pro with a front bezel is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection for any device and the fastest charging for your device onboard. Flip Pro with front bezel was manufactured as an adaption to the original SC-USB-F1 to offer flexibility to installation, as in some cases, it is not possible to gain access to behind panels. Therefore, the front fit bezel provides an alternative route for installation, allowing the option to fit the product from the front using screws. When not in use, the spring-loaded cap remains tightly closed, protecting the ports from the elements. When charging, it quickly locks open to protect your cables when plugged in. Featuring a super compact footprint, Flip Pro is constructed from premium, marine-grade materials. and is IPX4 waterproof, making it completely washdown-ready. Flip Pro is FAST! It will charge at 36W on a 12V system or up to 60W on a 24V system. This makes it perfect for charging modern laptops via the USB-C port. It’s also 2x faster for charging large tablets and is designed to effortlessly charge both an iPad Pro & iPhone at the same time.  The install cut-out matches those of standard USB sockets for easy retrofit or swap of an existing USB charger, allowing you to keep up with the heavier power draws of modern electronic devices. Universal: Universal fit for any USB-A or USB-C connectors. Fast charge (60W max) up to 2 devices at a time. Easy Install, using standard USB mounting hole - 29mm (1 1/8”) Washdown Proof: IPX4 waterproof with the cover closed. Marine Ready: Internal anti-corrosion protective coating UV resistant 316 stainless hinge and spring Electrical Information: Input voltage: 10-30V DC (12/24V System) Input current Max: 6A (10A fuse recommended)  Standby power draw: 0.01W USB – C output:  60W max on 24V system 36W max on 12V system USB – A output:  36W max The charge cable supplied with your device (tablet, phone, action camera, etc) must be used to achieve maximum charge performance from this charger. Phones will charge at the same speed whether on a 12V or 24V input voltage system. However, a 24V system must be used to get the full 60W output suitable for fast-charging laptops.  What is USB-C?  More powerful - Our USB-C has no problems charging even the largest iPad Pro at twice the speed as a USB-A.  More Compact: The slim, oval shape is smaller than USB-A and is also symmetrical and reversible - no more having to flip the cable over to get it into the port! More Flexible: It’s fast becoming the universal connector/charge type on all devices, replacing the USB-A, USB-B, and Micro-USB. New devices are being launched with this charge option only e.g. iPhone 13.

BlueSolar PWM Charge Controller (DUO) LCD & USB Charge Control - 12/24VDC - 20A Features: Liquid Crystal Display Two 5 Volt USB outputs Lighting control function, fully programmable   Three-stage battery charging (bulk, absorption, float), fully programmable Load output with low voltage and manual disconnect (programmable) Load output protected against overload and short circuit Protected against reverse polarity connection of the solar panels and/or battery Charges two separate batteries Programmable charge current ratio External Temperature sensor Please contact your dealer for any returns, repairs or support issues related to this product.

20A Solar Charge Controller - 12/24V The MSK-20A is a 3-stage intelligent series-type PWM charge controller. It is based on an advanced design using a microcontroller for digital accuracy and fully automatic operation. It can be used for 12V or 24V battery systems. Features: 3-stage intelligent Series Type PWM charging Automatic battery voltage detection: 12V / 24V 100% input and output within -35 degrees C to +50 degrees C Electronic protections: overheating, overcharging, over-discharge, overload, and short circuit Reverse protection: any combination of solar module and battery Optional MSK-TS External Temperature Sensor Applications: Recreational and service vehicles  Off-grid grid Portable charging kits  Boats and marine crafts Fieldwork or mobile offices Telecommunications Specifications: Input: 12V / 24V Amps: 20 amps Weight: 0.66 (lbs) Weight: 0.3 (kgs) Dimensions: 6.28 x 3.2 x 1.89 in. Dimensions: 159.6 x 81.4 x 47.88 (mm)

RealPRO Series Battery Charger - 12A - 2-6A-Banks - 12V/24V RealPro Series battery chargers (formerly Recreation Series) are an affordable, reliable and safe battery charging system designed for everyday use. The system is engineered for users who need a charging system on an occasional basis and may not want or need the capabilities of a heavier duty and higher amperage product. It is designed for use in many types of applications including bass boats, runabouts, pontoon boats, other watercraft, automobiles, ATVs, golf carts and other similar uses. The system delivers sophisticated capabilities and superior value to customers. Battery Charging Systems Designed for Everyday Applications Affordable, Reliable and Safe Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Wide Variety of Applications Universal Input (100-240 VAC 50/60HZ) Features: Approved for Wet Cell and Absorbed Glass Mat (AGM) batteries Designed for use in fresh and salt water Dependable, rugged construction and waterproof Independent outputs and fully automatic Battery maintenance mode Two year warranty DC charge cables = 5ft and AC power cord = 3ft Approved and meets ISO 8846 Marine standards Models available to charge 12-24V systems LED lights indicate “Each Battery’s” state of charge Reverse polarity protected and no installation restrictions Ignition protected (US Coast Guard 33 CFR 183.410) FCC 15 Parts A and B Interference Compliant May be used in many types of sporting applications including: Bass Boats Runabouts Pontoons Automobiles ATVs Golf Carts… This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

ROKK Wireless Nano 10W Waterproof 12/24V Charger Dock. Charge. Connect. Nano 10W is our smallest wireless phone charging mount. It squeezes big features into a tiny package! Designed to be installed where space is at a premium, Nano 10W holds and wirelessly charges your phone at the same time! The ultra-compact design can be installed and used in any orientation, unlocking new charging possibilities. Now you can keep your phone within reach, charged, and ready to go. The IPX6 waterproof, 12/24V wireless range enables phone charging for the outdoor environment, without the need for cables. Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use onboard. Perfect for boat consoles or any vehicle working outside in the elements, Nano 10W has been designed to fit even the largest phones. Nano 10W features Qi-certified wireless charging technology with foreign object detection and thermal cut-off to guarantee your devices are kept safe and charged while onboard. The upgraded 10W chargers are up to 60% faster and have been designed for the latest generation of power-hungry devices and apps. Nano 10W is compatible with all wireless charging-enabled phones of all sizes from all major brands. Charging is also possible through non-metallic, waterproof cases.  Usage Nano 10W is at home in coastal and freshwater. If you require a wireless phone charging mount for rough conditions, we recommend our ROKK Wireless – Active 10W or Edge 10W.   Testing ROKK Wireless Nano has been subjected to a high level of environmental, vibration, impact and on-water testing programs. This is combined with our world-renowned expertise in waterproofing technologies, UV stabilization techniques and premium-grade materials, ensuring Nano 10W is up to the challenge of life outdoors. Installation Installation is simple on any boat, RV, ATV or outdoor location. Four screws secure the unit onto any flat surface with a simple installation guide and drilling template. For the best phone grip performance, a vertical installation is recommended. The charger is easy to clean and can be washed down with fresh water. Features: 10W Fast Charging IPX6 Waterproof Qi Certified Mount & charge Outdoor-ready grip

AQUA JET DUO 10.4GPM 24V

ChargeMaster Battery Charger - 12 Amp - 3 Bank - 24V Power You Can Rely On Make the most of your batteries with the ChargeMaster, plugging in and charging anywhere in the world. Mastervolt’s ChargeMaster guarantees fast and complete charging of your batteries no matter where you are. The ChargeMaster can charge multiple battery banks simultaneously thanks to its combined functionality. Moreover, all ChargeMasters can be easily connected to a MasterBus network with only one cable and one connection (not available on ChargeMaster 24/6). You also have the option of central, local or remote monitoring, configuration and control of your system. The ChargeMaster is available in various models to guarantee you the ideal battery charger for any situation and demand. Charging Your Batteries With Every Voltage The Mastervolt ChargeMaster supplies a maximum capacity wherever you are via auto-ranging. Auto-ranging ensures perfect fully automatic operation anywhere in the world, regardless of the available mains voltage (90-265 V AC, 50 or 60 Hz). The 3-step+ charging technology guarantees fast and complete charging, while the cos phi 1 regulation gets the most out of limited generator capacity.  Sturdy Connections  Metal-on-metal fitting gives a firm connection, and prevents corrosion or overheating of contact surfaces. Charging Multiple Battery Banks  The ChargeMaster series has three equal charge outputs. Those of the smaller ChargeMaster models are pre-installed with two meters of cable for a plug & play solution, while the heavier models have one full output (for example for your service battery) and two outputs of 10 A, ideal for your starter batteries. Features: 3-Step+ charging technology for fast and complete charging. Safe and complete charging due to standard safety features. Memory function prevents overcharging in case of an unstable power supply. Clear control panel. Easy to install. Built-in system functionality (MasterBus) in combination with other Mastervolt products (not available on ChargeMaster 24/6). General Specifications Nominal output voltage: 24 V  Total charge current:12 A  Number of battery outlets: 3  Charge current second output: 12 A  Charge current third output:12 A  Battery capacity range: 24-120 Ah  Nominal input voltage: 120/230 V (90-265 V), 50/60 Hz AC connection: 2M AC cable Power supply mode: yes Display/read-out: LED display Fastening: 4x screw Dimensions, H x W x D: 234 x 132 x 60 mm / 9.2 x 5.2 x 2.4 inch Weight: 1.8 kg / 4.0 lb Approvals:CE, ABYC A-31, SAE J1171/ISO8846 ignition protected Technical Specifications Charge characteristic: IUoUo, automatic / 3-step+ for gel/AGM/wet/Lithium Ion Charge voltage Bulk: 28.8 V Charge voltage Absorption: 28.5 V Absorption time: 4 hours Charge voltage Float (wet batteries): 26.5 V Charge voltage Float (gel/AGM batteries): 27.6 V Temperature compensation: -60 mV/ °C -33 mV/ °F Voltage compensation: automatic Power consumption (DC side): < 2 mA Full load consumption (230 V AC): 435 W Current Control function: no Power factor control: ≥ 0.98 Temperature range (ambient temp.): -25 °C to 60 °C, derating > 25 °C -13 °F to 140 °F Sound level: < 52 dBA at 1M Protection degree: IP23 Protections: over temperature, over load, short circuit, high/low battery voltage Cooling: vario fan MasterBus compatible: yes WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Digital Automatic Charger - 1 Amp Vexilar Quick Connect system will connect directly to your Vexilar pack for charging. If yoursystem  does not have the quick connect system you can use the supplied  gator clip option for charging. The V-410 is a fully automatic 1 amp digital charger. It also serves as a battery maintainer. After the charger bring the battery to a full charge, it automatically switches to a float mode. The battery is held at a full charge until you're ready to use it. The storage period is the most difficult part your batteries life. During this time, the battery can degrade, sulfate, and be unusable when you need it. That's why you need to maintain the battery during storage periods. You could mark your calendar and charge your battery each month, or you could connect this Universal 12 Volt Automatic Charger and be assured that your battery will be ready to go when you are. Features: Fully Automatic 3- Stage Charging 1 Amp 12 Volt Output Digital Operation - No Heavy Transformer Will NOT Overcharge the Battery When Full, Maintains the Battery Charge Colored LEDs Indicate Charge Mode Connect it and Forget it Quick connect feature for Vexilar packs or use supplied gator clips direct to battery for charging. Specifications: 12 Volt / 1 Amp DC Output 100 - 240 Volt AC, 22 Watt Input 50/60 Hz Class 2 Battery Charger UL Approved One Year Warranty WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.