Mini Battery Selector Switch The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory. Housed in the same dimensions as the 701, and includes the same removable side plates and back cover Please note selector switches will not separate electronics from harmful engine starting spikes Tin-plated copper studs and nuts Ignition-protected WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy-Duty Battery Selector Switch The 721 Battery Selector Switch is our heavy duty selector switch. Housed in the same module as the 720, it includes the same removable plates and back cover. While BEP Marine recommends isolated battery systems as outlined with our distribution clusters, the 721 offers a simple economical way of separating two batteries. Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications: DC Voltage: 48 Stud Size (Imperial): 3 x 3/8" Stud Size (Metric): 2 x 10mm Continuous Rating: 350 Intermittent Rating: 500 Cranking Rating: 1500 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off) As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Medium Duty Battery Selector Switch w/Key Lock Perko's 8501 Series battery selector switches are among the most popular battery switches ever produced. Their use of the traditional Perko bolt circle makes for easy installation, whether new or as a replacement. These switches can be mounted in numerous locations. And as ignition protected switches, they can be installed in the engine rooms of gasoline powered boats. In addition to doing everything a battery disconnect switch does, battery selector switches permit battery selection (of two or more batteries) for specific purposes including starting engines, running accessories or even recharging. They allow for the use of one or more batteries in systems with one or more engines and facilitate putting batteries in parallel for emergency starting when one or both batteries are substantially discharged. Perko battery switches are designed for surface mounting. Standard duty switches have a bright red polycarbonate housing for safety with a large easy-to-turn black knob. The housing of the heavy duty switches are red fiber-reinforced polycarbonate. Selector switches are designed with a "make before break" feature. This allows switching between the "1", the "ALL" and the "2" positions while the engine is running. Models with an "Alternator Field Disconnect" feature offer protection for Non-Unitized Alternators should the switch accidentally be turned to the "OFF" position with the engine running. Versions of the 8501 Series switches offer additional features such as alternator disconnect and key lock security. The 90° rotation feature allows users to feel the switches' position in no light situations and the classic shape of the knob makes it easy to turn. High conductivity studs are long enough to handle more than 1 cable and strong enough for torque needed for secure connections. Optional spacer ring (PN 0462DP0RED) allows for the use of larger cables. Specifications: Diameter: 5-1/4" Depth: 2-5/8" For use with 6 to 50 Volt Marine Electrical Systems Capacity - 250 AMPS Continuous, 360 AMPS Intermittent When used with Non-Unitized Alternators, these models will interrupt the field current (reducing the possibility of damage) if turned "OFF" with the engine running

Compact Battery Selector & Main Disconnect Switches Ignition Protected For use with 12, 24 and 32 volt marine electrical systems Higher Rating Than Popular 8500 Series Switches Same bolt patterns as popular 8500 series Smooth, positive position selector Compact, Medium Duty Battery Selector Switch

Compact Battery Selector & Main Disconnect Switches Ignition Protected For use with 12, 24 and 32 volt marine electrical systems Higher Rating Than Popular 8500 Series Switches Same bolt patterns as popular 8500 series Smooth, positive position selector Compact, Medium Duty Battery Selector Switch w/ Key Lock

Dual Battery Selector Switch - Cup Mount The Perko Dual Battery Selector Switch allows the addition of an extra battery for accessories. This switch provides the flexibility of selection between batteries or combined operation of both batteries in parallel for starting or charging. It can also serve as an emergency main disconnect switch in the event of an electrical problem. All models are make before break design and are ignition protected. Features: For two or more batteries Unique oval shape mounts in a round hole Removable actuator key

Battery Selector Switch with AFD Part No. 2110A Description Continuous Amps: 230 Momentary Amps: 345 Dimensions: 5"D x 2-3/4"H Product Features Alternator field disconnect (AFD) allows selection of any positions, including "off" without damage to alternator or electrical system. AFD is required on some electrical systems. Heavy duty copper sweep contacts "Make before break" contacts allow selection of all positions except "off" while engine is running Use with 6, 12, 24 or 36 volt systems New design is easy to retrofit into existing hole patterns Built-in skirt protects connections Exclusive flat 360 degree "sweep" contact design provides up to 60% more contact area than other switch designs Surface or rear panel mounting Marine grade construction One year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Medium Duty Battery Selector Switches Ignition Protected For use with 12, 24 and 32 volt marine electrical systems Capacity - 250 AMPS continuous, 360 Amp Intermittent Medium Duty Battery Selector Switch w/ Alternator Field Disconnect w/o Key Lock

Medium Duty Battery Selector Switches Ignition Protected For use with 12, 24 and 32 volt marine electrical systems Capacity - 250 AMPS continuous, 360 Amp Intermittent Medium Duty Battery Selector Switch w/ Alternator Field Disconnect w Key Lock

Cruiser Series Battery Selector Switch without AFD This battery switch can be used on 6, 12, 24 or 36V systems. Features: Polycarbonate case Surface mount Cable Lug Size: 3/8" Dimensions: 5.50" x 2.63" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Cruiser Series Battery Selector Switch with AFD Part No. 2100 Description Continuous Amps: 230 Momentary Amps: 345 Cable Lug Size: 3/8" Color: Orange Dimensions: 5-1/2"W x 2-5/8" Product Features Alternator field disconnect (AFD) allows selection of any position, including "off" without damage to alternator or electrical system Polycarbonate case For 6, 12, 24 or 36 volt systems One year Warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Diesel Power Battery Selector Switch Product Features Polycarbonate case For 6, 12, 24 or 36 Volt systems Alternator field disconnect (AFD) allowing selection of any position including "off", without damage to alternator or electrical system One year warranty Specifications: Continuous Amps: 360 Momentary Amps: 600 Cable Lug Size: 1/2" Color: Gray Dimensions: 5-1/2" sq x 3-1/2"H WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Selector Switch Part No. 2111A Features New ergonomically styled turn knob provides easy On/Off switching Updated color scheme and graphics make it easier to determine switch status Longer stud lengths for improved assembly and easier cable routing Built with heavy-duty copper sweep contacts to ensure positive circuit control Rugged internal components protected by a tough, impact resistant polycarbonate housing that is impervious to the elements One year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy Duty Battery Switch Ignition Protected For use with 6, 12, 24 and 32 volt marine electrical systems capacity - rated 380 amps continuous, 850 amps intermittent (5 mins on, 5 mins off) Heavy Duty Battery Selector Switch w/ Alternator Field Disconnect