Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch - MC10 Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8 inch) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint For surface mounting only Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems, both banks must be same voltage) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1, 1/2, Parallel, Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount On/Off Battery Switch - MC10 As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Features: Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 2x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Double Pole Battery Switch - MC10 An addition to our multi award winning Pro Installer EZ Mount range, this battery switch provides Double Pole On/Off functionality so that both positive and negative battery terminals can be isolated. Most commonly used on metal hulled craft, full isolation ensures there is no risk of stray currents that may cause galvanic corrosion, and also guarantees optimum safety during servicing or mishap, for example with mining equipment. As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Features: Tested to UL1107 ignition protection, CE Tinned copper 10 mm (3/8 in) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint Surface mount only Each Pro Installer battery switch is fully tested for pressure sealing, Rotation force and electrically load tested Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off) As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Dual Bank Control Switch - MC10 Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8 inch) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint For surface mounting only Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems, both banks must be same voltage) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1, 1/2, Parallel, Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Double Pole Battery Switch - MC10 A powerful new generation battery switch with outstanding performance and features for both the installer and end user. Three mounting options: surface, rear panel, and front panel mounting, plus optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. Same industry standard mounting with On/Off operation. Used where positive and negative supplies must be isolated at the same time. SAFETY NOTE: BEP does not recommend this for switching house and start battery systems at the same time, for safety reasons. You may need to isolate your engine battery in an emergency, but not your house battery which typically powers the communications Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Selector Battery Switch - MC10 Power requirements on boats have increased, and these 2 Selector switches offer high power capacity (400 amps continuous), the ability to easily fit doubled cables, and conform to the industry standard mounting footprint (Guest, Perko, Blue Sea). Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Selector w/Field Disconnect Battery Switch - MC10 Power requirements on boats have increased, and these 2 Selector switches offer high power capacity (400 amps continuous), the ability to easily fit doubled cables, and conform to the industry standard mounting footprint (Guest, Perko, Blue Sea). Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

BEP Pro Installer Terminal Block - 6 Way - 30A This terminal block is ideal for isolated connections up to 30A and suitable for connecting tails from AC and DC panels. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

5511e Dual Circuit Plus Battery Switch CE Marked Ignition protected - Safe for installation aboard gasoline powered boats Case design allows surface or rear panel mounting Meets American Boat and Yacht Council (ABYC) requirements for battery switches 3/8" - 16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals 7/8" stud length to accept multiple cable terminals Tactile textures indicate knob position by feel only WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Class T Fuse Holder with 2 Additional Studs 225-400A Providing high-capacity fusing, fast response and very high interrupt ratings (ANL up to 6,000 Amps, Class-T up to 20,000 Amps), these fuse holders are ideal for protecting today's demanding onboard power electronics technology including inverters and battery chargers. They also protect wiring from short circuits. Pro Installer fuse holders' durable construction allow fuses to run at maximum load. Radiused ends improve cable routing options Class-T: 225-400 Amp WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Multi Purpose Buss Bar - 4 Way 1/4" Studs/150A Pro Installer Bus bars offer the installer greater flexibility to select buss bars to match their load and space requirements. Compact footprints and modular designs allow for space saving and scalability. Robust construction, thicker copper conductors and additional mounting holes provide the basis for secure, reliable, electrical installations. The covers feature snap-out side skirts providing additional cable entry as required, while the label recess provides the perfect landing for handheld-printer labels. it is easy linking to other Pro Installer products because of the common interconnection height, and the radiused busbbar ends improve cable routing options for large cables. Bus Type: 4 way Output screws: 1 x 4 Input studs: 4 x 6 mm (1/4 stud) Rating (A): 150 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer Link Joiner 3-Way Pro Installer link bars provide the fastest and most economical way of connecting the Pro Installer line of products to save space and allow for the most compact installations. The common interconnection height of Pro Installer components allows link bars to quickly and easily convert a group of different products into a functional cluster. Pro Installer link bars are made of high purity copper and are tin plated for optimum marine electrical performance. Links can be doubled to accommodate higher loads.

Pro Installer Link Bar 35.5 - 42.5mm *5-Pack Pro Installer link bars provide the fastest and most economical way of connecting the Pro Installer line of products to save space and allow for the most compact installations. The common interconnection height of Pro Installer components allows link bars to quickly and easily convert a group of different products into a functional cluster. Pro Installer link bars are made of high purity copper and are tin plated for optimum marine electrical performance. Links can be doubled to accommodate higher loads.

500A 4 Stud Buss bar Pro Installer buss bars are designed for flexibility and scalability. The snap-out side skirts allow for additional cable entry, and radius ends improve cable routing options. it is easy to link other Pro Installer products to the buss bars because of the common interconnection height in the product line. Compact footprint saves space Clear, polycarbonate covers insulate and protect on three sides Secure cover attachment does not interfere with cabling Snap-out skirts for flexible cable entry Radiused ends improve cable routing Long, threaded studs to connect up to (4) large cable lugs Plated brass nuts and stainless steel studs prevent thread galling during tightening WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.