Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off) As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Dual Bank Control Battery Switch - MC10 Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8 inch) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint For surface mounting only Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems, both banks must be same voltage) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1, 1/2, Parallel, Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount On/Off Battery Switch - MC10 As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Features: Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 2x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A EZ-Mount Double Pole Battery Switch - MC10 An addition to our multi award winning Pro Installer EZ Mount range, this battery switch provides Double Pole On/Off functionality so that both positive and negative battery terminals can be isolated. Most commonly used on metal hulled craft, full isolation ensures there is no risk of stray currents that may cause galvanic corrosion, and also guarantees optimum safety during servicing or mishap, for example with mining equipment. As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Features: Tested to UL1107 ignition protection, CE Tinned copper 10 mm (3/8 in) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint Surface mount only Each Pro Installer battery switch is fully tested for pressure sealing, Rotation force and electrically load tested Specifications Mounting: Surface Only Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Double Pole Battery Switch - MC10 A powerful new generation battery switch with outstanding performance and features for both the installer and end user. Three mounting options: surface, rear panel, and front panel mounting, plus optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. Same industry standard mounting with On/Off operation. Used where positive and negative supplies must be isolated at the same time. SAFETY NOTE: BEP does not recommend this for switching house and start battery systems at the same time, for safety reasons. You may need to isolate your engine battery in an emergency, but not your house battery which typically powers the communications Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: On/Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Selector Battery Switch - MC10 Power requirements on boats have increased, and these 2 Selector switches offer high power capacity (400 amps continuous), the ability to easily fit doubled cables, and conform to the industry standard mounting footprint (Guest, Perko, Blue Sea). Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Selector w/Field Disconnect Battery Switch - MC10 Power requirements on boats have increased, and these 2 Selector switches offer high power capacity (400 amps continuous), the ability to easily fit doubled cables, and conform to the industry standard mounting footprint (Guest, Perko, Blue Sea). Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1-2-Both-Off Stud: 3x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Installer 400A Dual Bank Control Switch - MC10 Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8 inch) studs Stainless steel washers and nuts Fiber reinforced plastics 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating) Waterproof to IP67 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable side plates for protection Industry standard 3.85 x 3.85 inch footprint For surface mounting only Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested Specifications Mounting: Surface, Rear or Front Voltage: 48v DC (for 12-48v systems, both banks must be same voltage) Rating: 400 Cont / 600 Inter / 1500 Crank Dims: 3.85" x 3.85" x 3.62" Operation: 1, 1/2, Parallel, Off Stud: 4x 10 mm (3.8") WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mini Battery Selector Switch The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory. Housed in the same dimensions as the 701, and includes the same removable side plates and back cover Please note selector switches will not separate electronics from harmful engine starting spikes Tin-plated copper studs and nuts Ignition-protected WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Medium Duty Battery Selector Switch w/Key Lock Perko's 8501 Series battery selector switches are among the most popular battery switches ever produced. Their use of the traditional Perko bolt circle makes for easy installation, whether new or as a replacement. These switches can be mounted in numerous locations. And as ignition protected switches, they can be installed in the engine rooms of gasoline powered boats. In addition to doing everything a battery disconnect switch does, battery selector switches permit battery selection (of two or more batteries) for specific purposes including starting engines, running accessories or even recharging. They allow for the use of one or more batteries in systems with one or more engines and facilitate putting batteries in parallel for emergency starting when one or both batteries are substantially discharged. Perko battery switches are designed for surface mounting. Standard duty switches have a bright red polycarbonate housing for safety with a large easy-to-turn black knob. The housing of the heavy duty switches are red fiber-reinforced polycarbonate. Selector switches are designed with a "make before break" feature. This allows switching between the "1", the "ALL" and the "2" positions while the engine is running. Models with an "Alternator Field Disconnect" feature offer protection for Non-Unitized Alternators should the switch accidentally be turned to the "OFF" position with the engine running. Versions of the 8501 Series switches offer additional features such as alternator disconnect and key lock security. The 90° rotation feature allows users to feel the switches' position in no light situations and the classic shape of the knob makes it easy to turn. High conductivity studs are long enough to handle more than 1 cable and strong enough for torque needed for secure connections. Optional spacer ring (PN 0462DP0RED) allows for the use of larger cables. Specifications: Diameter: 5-1/4" Depth: 2-5/8" For use with 6 to 50 Volt Marine Electrical Systems Capacity - 250 AMPS Continuous, 360 AMPS Intermittent When used with Non-Unitized Alternators, these models will interrupt the field current (reducing the possibility of damage) if turned "OFF" with the engine running

Heavy-Duty Battery Selector Switch The 721 Battery Selector Switch is our heavy duty selector switch. Housed in the same module as the 720, it includes the same removable plates and back cover. While BEP Marine recommends isolated battery systems as outlined with our distribution clusters, the 721 offers a simple economical way of separating two batteries. Please note selector switches will not separate electronics from harmful engine starting spikes. Specifications: DC Voltage: 48 Stud Size (Imperial): 3 x 3/8" Stud Size (Metric): 2 x 10mm Continuous Rating: 350 Intermittent Rating: 500 Cranking Rating: 1500 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual Battery Selector Switch - Cup Mount The Perko Dual Battery Selector Switch allows the addition of an extra battery for accessories. This switch provides the flexibility of selection between batteries or combined operation of both batteries in parallel for starting or charging. It can also serve as an emergency main disconnect switch in the event of an electrical problem. All models are make before break design and are ignition protected. Features: For two or more batteries Unique oval shape mounts in a round hole Removable actuator key

Battery Selector Switch with AFD Part No. 2110A Description Continuous Amps: 230 Momentary Amps: 345 Dimensions: 5"D x 2-3/4"H Product Features Alternator field disconnect (AFD) allows selection of any positions, including "off" without damage to alternator or electrical system. AFD is required on some electrical systems. Heavy duty copper sweep contacts "Make before break" contacts allow selection of all positions except "off" while engine is running Use with 6, 12, 24 or 36 volt systems New design is easy to retrofit into existing hole patterns Built-in skirt protects connections Exclusive flat 360 degree "sweep" contact design provides up to 60% more contact area than other switch designs Surface or rear panel mounting Marine grade construction One year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Selector Switch Part No. 2111A Features New ergonomically styled turn knob provides easy On/Off switching Updated color scheme and graphics make it easier to determine switch status Longer stud lengths for improved assembly and easier cable routing Built with heavy-duty copper sweep contacts to ensure positive circuit control Rugged internal components protected by a tough, impact resistant polycarbonate housing that is impervious to the elements One year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Compact Battery Selector & Main Disconnect Switches Ignition Protected For use with 12, 24 and 32 volt marine electrical systems Higher Rating Than Popular 8500 Series Switches Same bolt patterns as popular 8500 series Smooth, positive position selector Compact, Medium Duty Battery Selector Switch