Thirsty-Mate High Capacity Super Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Capacity: 30 gal/min Length: 33" Diameter: 3" Stroke Length: 19" Intake Hose: 4' Outlet Hose: 6' WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flex-a-Pump Impossible Place Pumps A Thirsty-Mate with extra reach! This pump can be permanently installed and will operate in any position. It comes complete with mounting brackets, intake hose and clamp, strainer, check valve and discharge hose. Ideal for small boats, engine compartments and much more. Features: Diameter: 1-3/4" (44 mm) Length: 14" (35.6 cm) Stroke: 12" (30.5 cm) Gal/Min: 7.5 (28 L) Outlet Hose: 2' (61 cm) Intake Hose: 4' (1.2 m) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate High Capacity Super Pump Coast Guard Approved for commercial use Manufactured to exceed the original requirements of Coast Guard regulation No. 519C. The specifications of this regulation were later reduced when no hand pump other than Beckson's could pass the test requirements. Still "over built" to Beckson's higher standard. Length: 24" Diameter: 3" GPM: 22 Inlet Hose: 36" Outlet Hose: 120" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flex-a-Pump Impossible Place Pumps A Thirsty-Mate with extra reach! This pump can be permanently installed and will operate in any position. It comes complete with mounting brackets, intake hose and clamp, strainer, check valve and discharge hose. Ideal for small boats, engine compartments and much more. Features: Diameter: 1-3/4" (44 mm) Length: 14" (35.6 cm) Stroke: 12" (30.5 cm) Gal/Min: 7.5 (28 L) Outlet Hose: 2' (61 cm) Intake Hose: 6' (1.8 m) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tournament Series 1600 GPH Livewell Pump Dual Port Rule 209FDP Marine 1600 Tournament Series Livewell Pump (1" NPT, Female-Dual Port) Features: Highest capacity livewell pump in today's market Glass filled nylon dual port base for optional washdown pump connection Anti-airlock feature, heavy-duty long-life motor 1' (25mm) NPT female intake, 1-1/8" (29mm) discharge outlet and a 1/2" (6mm) NPT threaded port for washdown installation 1600 GPH (6054 LPH) dual port, 12V DC Sport type: Boating Color: White

Rule 209FDP 12V Dual-Port Livewell Pump Highest capacity livewell pump in today's market Glass filled nylon dual port base for optional washdown pump connection Anti-airlock feature, heavy-duty long-life motor 1' (25mm) NPT female intake, 1-1/8" (29mm) discharge outlet and a 1/2" (6mm) NPT threaded port for washdown installation 1600 GPH (6054 LPH) dual port, 12V DC  

Grey Waste Tanks with Intelligent Control Robust compact tanks with multi-port options to suit your installation. Whale’s Largest Range of Multi-Port Grey Waste Tanks Ever! Simple system - Allows you to manage all grey waste on board through one thru-hull fitting. Resilient polyethylene one-piece moulded tanks designed to handle grey waste on board - ideal for use with Gulper Grey Waste pumps for unbeaten debris handling. 8 liter capacity grey waste tanks - compact design allows you to mount a Gulper pump directly to the side to save space and simplify pipe runs. 16 liter capacity grey waste tanks - higher capacity design allows you to mount a Gulper pump directly to the side to save space and simplify pipe runs. 20 liter capacity grey waste tanks - outlet ports and sensor locations minimize air pumping noise. Grey waste tank lid with fully integrated sensor: Intelligent Control - sensor activates pump automatically to empty grey waste tank only when required Robust - enclosed housing with dual seal ensures the best component protection in the harsh grey waste environment Reliable - designed to reduce dirt and debris build-up Compatible - lid design allows retrofitting to existing Whale grey waste tank systems Simple installation - two wires can connect to any 12 or 24V pump system, up to 20A, with no requirement for a relay WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

AquaT Electric Marine Toilet - Super Compact - 12V Priced competitively, the fine finish and design of this toilet are remarkable. Made from white vitreous porcelain with corrosion-resistant parts, this AquaT marine toilet is quiet, robust, and easy to clean. It is probably fair to think of most toilets as commonplace products, but one look at the features and it's easy to see that the AquaT is far from ordinary. Quiet, hygienic, and reliable, the AquaT marine toilet is perfect for almost any marine toilet room.  Features: Limited 2-Year Warranty Silent flush and discharge operation Included control panel for rinse and discharge pump; one-button multi-function discharge and rinse Flexible hole pattern on the base for easy substitution with the most common toilets on the market Smooth design for easy cleaning Accessible mounting points for fast installation Standard fastenings, logic located, no need for special tools High-capacity discharge pump Built-in rinse pump for raw water or fresh water from a separate toilet water tank (do not connect the toilet rinse pump to the boat's fresh/ drinking water system) Specifications: Volts: 12V Style: Super compact (smaller and lighter bowl, requiring less space)

Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.    March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower air cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   The TE-5.5C-MD pumps Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Nitric Acid, Phosphoric Acid, Potassium Chloride, Potassium Hydroxide, Sodium Hydroxide (Caustic Soda), Sodium Chloride, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.      Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V                   3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)

Little Giant Pump 582614 Little Giant TE-4-MD-HC 230V Magnetic Drive Pump Motor 230 Volt 50/60 Hz 1/10 HP Totally Enclosed Fan Cooled Motor, 850 GPH at 1 Foot Head, Shutoff Head 24.3 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Ryton Body, Fluid Temperature Up to 200F (93C), UR/C-CSA Listed, 6 Foot Power Cord- No Plug   582614 Magnetically driven pumps for circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions that are compatible with the pump's material of construction. The MD-HC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use.

Little Giant Pump 582514 Little Giant TE-4-MD-SC 230V w/cd Magnetic Drive Pump Motor 230 Volt 50/60 Hz 1/10 HP Totally Enclosed Fan Cooled Motor, 850 GPH at 1 Foot Head, Shutoff Head 24.3 Feet, Inlet: 1" FNPT, Outlet: 1/2" MNPT, Polypropylene Body, Fluid Temperature Up to 150F (66C), UR/C-CSA Listed, 6 Foot Power Cord- No Plug   582514 Magnetically driven pumps for semi-corrosive chemicals and solutions. The MD-SC Series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersed use.

2-Stage High Volume High-Pressure Digital Pump with Car/Battery Adapter Kit The fastest way to inflate HPI items to full pressure. Two separate ports for inflation and deflation. LED digital gauge display & auto-stop function when set to desired PSI. Equipped with 12V DC accessory outlet cable & car battery adapter kit. The nozzle is compatible with HR valves only. Maximum pressure of 20 PSI. Features: The fastest way to inflate HPI items to full pressure Automatic inflate and deflate functionality LED digital gauge and auto-stop function Equipped with 12V accessory outlet cable and car battery adapter kit Compatible with HR valves only 20 PSI max pressure

Flexible Shaft Coupling for 5" B/W, Hurth, & Volvo - 25HP/100RPM Capacity The R & D Marine Flexible Coupling consists of a flexible disc molded with a polyester elastomer. The disc gives clearance for bolt heads and is able to flex freely to take up any temporary misalignment of the engine and shaft due to flexing of the boat structure or the engine moving on its mount. Forward thrust is taken in compression on the disc between the two half couplings, and reverse thrust is retaken in compression on the disc between the two fail-safe straps. In the unlikely event of a severe impact, the steel straps make the coupling fail-safe and ensure the drive is maintained both forward and reverse. Reduce Engine Noise & Transmission Vibration Staggered bolts enable the element to isolate vibrations and compensate for some misalignment. Reduces Costly Transmission Repairs Absorbs shock loads due to hard gear changes. Fits Most Major Transmissions For engines, 5 to 1,500 horsepower It fits brands such as Borg Warner, ZF-Hurth, Twin Disc, Volvo, Yanmar, Technodrive, and more. Under Compression Load In Both Forward & Reverse The aft steel strap bolted to the transmission acts as a backing plate to prevent reverse thrust from pulling the element apart. Quick & Easy Installation The R & D Marine Flexible Coupling requires no machining and comes supplied with bolts to connect between the two existing shaft flanges. Extremely Durable Impervious to saltwater, diesel, and lubrication oils. The Flexible Couplings are made from a polyester elastomer not affected by saltwater, diesel, or lubrication fluids. Fail-Safe Design A fail-safe design is incorporated in the R & D Flexible Shaft Coupling that prevents the two couplings from pulling apart in the event of an impact or element failure, whereas other couplings do not. This fail-safe design is accomplished by using two steel straps and thru-bolts going into both the shaft coupling and transmission output flange. The aft steel strap is bolted to the transmission output flange, and the front strap is bolted to the shaft coupling. In the event of an impact, the aft steel strap (bolted to the transmission) will catch the front steel strap (bolted to the shaft coupling) and prevent the drivetrain from pulling apart. The R & D element will absorb the shock load (reducing or eliminating damage to the transmission) and will maintain contact between the two couplings. The steel straps also keep the R & D Flex-Coupling under a compression load in both forward and reverse operation (the aft strap bolted to the transmission acts as a backing plate). Machined Not Molded The Drivesaver is molded, while the R & D Flexible Shaft Coupling is machined. Both designs suggested that you first set your alignment by drawing the two couplings up to each other and then adding the flex-coupling. The machined part will have MUCH tighter tolerance than a molded part. Checking Alignment The R & D Flexible Shaft Coupling allows for alignment inspection after the element is bolted in place. There is one bolt head that is machined and painted red. After the R & D Flexible Shaft Coupling is bolted into place, a feeler gauge can be slipped between the red bolt head and the coupling. This process is repeated with the same bolt four times at 90-degree intervals by rotating the shaft. If the gap is within .010" (0.25mm), the engine is accurately aligned. To calculate the power of the coupling required: Horse Power of Engine x Reduction Ratio x 100 = HP/100RPM       Engine Speed   Example: Ford 150 HP at 2500 RPM with Borg Warner Velvet Drive 72C 2:1 Reduction Ratio Engine Horse Power is 150 HP, Max Rated RPM is 2500, Reduction Ratio is 2:1 150/2500 x 2 x 100 = 12 HP per 100RPM The coupling required is 910-009 Specifications: Manufacturer: B/W, Hurth, Volvo Diameter (inches/mm): 5 / 127 # of Bolts: 4 Diameter of Holes (inches/mm): 0.44 / 11.2 Bolt Pitch Circle (inches/mm): 4.25 / 107.9 Register (inches/mm): 2.5 / 63.5 Diameter (inches/mm): 5.63 / 143 Length (inches/mm): 2.06 / 52.4 Bolt Diameter: 7/16 UNF HP per 100 RPM (hp / kW): 25 / 18.64

Little Giant Pump 506055 Little Giant WRS-6 Sump Pump 5 gallon Tank made of Polypropylene it is lightweight and corrosion-resistant the cover is designed with O-rings for water tight seal the cover includes removable filter for easy cleaning and it is Pre-assembled and ready to install. Cover includes 1/1/2" FNPT (38 mm) discharge and intake opening, and 2" FNPT (5 cm) vent opening IAPMO listed   506055 Removes water from laundry trays, lavatory sinks, wet bar sinks, dehumidifiers, air conditioners (condensate), water softeners, etc. Installs above floor, no need to dig a sump. Unit is pre-assembled and ready to install

Little Giant Pump 506065 Little Giant WRSC-6 Sump Pump 3.5 gallon Tank made of Polypropylene, lightweight, corrosion-resistant, it's designed with O-rings for water tight seal. The cover includes removable filter for easy cleaning. Cover includes 1/1/2" FNPT (38 mm) discharge and intake opening, and 2" FNPT (5 cm) vent opening and it is Pre-assembled, ready to install IAPMO listed   Pump Features 1/3 hp. 115 Volt Multiple switch options cCSAus listed (pump only)   506065 Removes water from laundry trays, lavatory sinks, wet bar sinks, dehumidifiers, air conditioners (condensate), water softeners, etc. Installs above floor, no need to dig a sump. Unit is pre-assembled and ready to install.