Ampco Ac216Md14T-S, Viton Pump End Only with Max Impeller

Ampco AC114MD14T-S, Viton Pump End Only, with Max Impeller  

Ampco Pumps AC216MD14T-S Peo 2 X 1 1/2 Kit Ampco's AC Series pumps have standard stainless steel adapters and type D,DG & E seals available. The Ampco AC Series pumps are in conformance with 3A Sanitary Standards for centrifugal and positive rotary pumps for milk and milk products. # 02-10 This Ampco AC Series pumps also have a standard 32RA (150 grit) finish on all product surfaces.

Ampco Pumps AC114MD14T-S/VITON Peo Full Size Impeller

Ampco Pumps AC114MD56C-S/VITON Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps AC216MD56C-S/VITON Peo 2 X 1 1/2 Kit

Ampco Fluid End Aluminum Bronze Full Impeller for KC2 1 X 3/4

Ampco Pumps 216D-24B-316L Retainer (Impeller)

Ampco Pumps BI8202801-4.25 Bronze Impeller for KC2 1X3/4

Tuthill 1LEV-C-7 Pump 3.2 Gpm Cast Iron Rotary Gear Pump Pump End Only Tuthill L Series Pump Cast Iron Construction Has Internal Relief Valve Relief valve is set at 55 PSI (can be adjusted in field). Clockwise rotation only (from shaft end view) Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Tuthill 4105V-CC-A-7 Pump Tang Shaft Viton Cast Iron Rotary Gear Pump Pump End Only 5.6 GPM 4105 Series Pump Cast Iron Construction Has Internal Relief Valve Relief valve is set at 55 PSI (can be adjusted in field) COUNTER Clockwise rotation only (from shaft end view) Tang Shaft Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT

Tuthill 4108-V-CC-A-7 Pump Tang Shaft Gear 1" Tuthill 4108V-CC-A-7, Cast Iron Rotary Gear Pump. Pump End Only. 13 GPM 4108 Series. Cast Iron Construction NO motor. Has Internal Relief Valve. Relief valve is set at 55 PSI (can be adjusted in field). COUNTER Clockwise rotation only (from shaft end view). Tang Shaft. Inlet Port is 1 inch NPT, Discharge Port is 1 inch NPT.   Features Pump Body: Cast Iron Relief Valve: Relief valve is factory set to 55 PSI for adjustment between 40-70 PSI. Other PSI ranges available. Shaft Seal :Mechanical Seal Viton Port Size: Inlet Port is 1 inch NPT Discharge Port is 1 inch NPT.

Tuthill 4C2FV-C-A-7 Gear Pump (505000) Tuthill 4C2FV-C-A-7, Cast Iron Rotary Gear Pump. Pump End Only. 36 GPM C Series. Cast Iron Construction NO motor. Flange mount. Has Internal Relief Valve. Relief valve is set at 90 PSI (can be adjusted in field). Clockwise rotation only (from shaft end view). Tang Shaft. Inlet Port is 1-1/2 inch NPT, Discharge Port is 1-1/2 inch NPT.   Features : Pump Body:Cast Iron  Relief Valve:Relief valve is factory set to 90 PSI for adjustment between 30-225 PSI. Other PSI ranges available.  Shaft Seal:Sleeve Bushing Lip Seal Viton  Port Size:Inlet Port is 1-1/2 inch NPT Discharge Port is 1-1/2 inch NPT.

Bosworth 2800 Guzzler Aluminum Pump Bosworth Diaphragm Pump End Only Guzzler Aluminum, 13.4GPM, 2” Smooth Ports, 56C Motor Flange, Buna Flapper Valves and Diaphragm   2800 Requires a 1/2HP Motor this is the pump only

Oberdorfer N13HDM-E24 Clutch Pump 1.5"24V Oberdorfer N13HDM-E24 is a Bronze pedestal Gear Pump with 24 Volt DC Clutch Bronze Gears Buna Mechanical Seal Stainless Steel shaft 1-1/2 Inch NPT Ports Pump end only no Motor   This pump is self-priming, and the maximum suction lift for this pump is 20 feet, however, the suction line should be as short as possible. The recommended discharge pressure limits for this pump are 100 PSI for water and non-lubricants, 150 PSI for oil and other lubricants, as the high pressure will accelerate wear.    A relief valve is necessary to protect the pump and system if the discharge line becomes blocked or closed.