|
Micro 4-Way Instrument Drop
The Actisense 4-way drop makes it easier to reach up to four devices with a single cable.
Typically, when four devices need to be connected to an NMEA 2000 backbone, a T-piece and individual cable is required for each one. This can either mean excessive cabling demands or moving the backbone closer to your devices.
The 4-way drop makes it possible to shorten the length of each cable needed before reaching a T-piece.
|
130.09 |
|
|
N2K Micro 4 Way T-Piece
The Actisense 4 Way T-Piece is for use where multiple drops or ‘ports’ are required from the NMEA 2000 backbone. It’s as quick and easy to install as a single T-Piece, uses less space than two individual T-pieces, and costs less than four.
The Actisense range of NMEA 2000 connectors and cables has been designed using our specialist interconnect and NMEA knowledge.
Features:
NMEA 2000 Approved
RoHS Compliant
Specifications:
Rated Current: 4A
Rated Voltage: 60V DC
Male Contact: Brass, gold plated
Female Contact: Phosphor bronze, gold plated
Contact Carrier: PA66 (30% Glass filled), black
Contact Polarization: Standard M12 -“A”- polarization
Mating Thread: M12
Screw Cap: Brass, nickel plated
O-Ring Seal: Rubber, Black
Housing: TPU, flame retardant to UL94V-0, Halogen Free
Internal Housing Shield: Copper Foil
Weight: 105g
Protection: IP67 (when mated)
Operating Temperature: -20°C to +70°C
Storage Temperature: -40°C to +85°C
|
127.42 |
|
|
Splash Proof Panel - 4 Way - White
Features:
Compact panel size
Sprayproof inline fuse holders with fuses included
Waterproof power receptacles (16A) in five and three way models
Waterproof to IP56
Switches rated at 20A DC
LxWxH is 3.75'x4.25'x2.9' (95x107x75 mm)
Panel supplied with label LBL-WP
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
29.99 |
|
|
Circuit Breaker Panel - 4-Way
BEP Marine uses the highest quality materials in its range of Control Panels, from the marine grade aluminium base plates to the Airpax magnetic hydraulic circuit breakers.
Features
Marine Grade powder coated aluminium
Airpax circuit breaker
Stylish Contour Design fascia
Green LED backlit labels
Red LED indicates systems on
Panels meet ABYC standards
Specifications
Total Positions: 4 Loads
Circuit Breakers: 1X 5A, 2X 10A, 1X 15A
Nominal Voltage: 12V
Maximum Amperage: 80A
Dimensions: 4.5" X 5" X 2.5"
Neg Bus: 6 Way
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
136.90 |
|
|
4-Way Nylon Heavy-Duty Ratchet Mount with Cable Slot & Built-In Coax Cable Feed-Thru 1"-14 Thread
4 way ratchet mount in reinforced nylon UV resistant design with handle for deck or bulkhead. Hole for GPS and feed-thru for coax cable. Usable with antennas no longer than 9' in self supporting mode. Standard 1" x 14 thread.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
16.79 |
|
|
AC Circuit Breaker Panel without Meters, 4 Way Panel 2 Mains - 110V
Ideal for AC shore power installations and on board inverter installations.
Specifications:
Nominal Voltage: 110V AC
Total Positions: 4 Loads + 2 Inputs
Circuit Breakers (Single + Double Pole): 2x 15A, 2x 20A, + 2x 30A
Maximum Aperage: 30A
H x W x 2.5": 4.5" x 9.4"
Neg Bus: IS-6mm-2
Label Sheet: 5
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
346.18 |
|
|
AC Circuit Breaker Panel without Meters, 4 Way Panel 2 Mains - 240V
Ideal for AC shore power installations and on board inverter installations.
Specifications:
Nominal Voltage: 240V AC
Total Positions: 4 Loads + 2 Inputs
Circuit Breakers (Single + Double Pole): 2x 10A, 2x 15A, + 2x 20A
Maximum Aperage: 20A
H x W x 2.5": 4.5" x 9.4"
Neg Bus: IS-6mm-2
Label Sheet: 5
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
366.30 |
|
|
4-Way Block for NMEA 2000 Networks
Navico's 4-Way Block accessory for NMEA 2000 Networks should be used where
multiple drop-cables are required in close proximity to make a more
cost-effective and streamlined solution compared to installations that use
multiple T-connectors.
|
49.51 |
|
|
OPTO-4 Isolated NMEA to RS232 Adapter
Isolate an RS232 (PC) port to protect against ground loops...
The Actisense OPTO-4 is a bi-directional NMEA 0183 (RS422) to RS232 interface cable which provides a safe method of connecting an NMEA 0183 system to a laptop PC or any device with a standard RS232 9-pin port. The isolation protects the connected device, so any potentially hazardous voltages on the NMEA 0183 bus do not cause damage to the PC hardware, offering the user complete peace of mind.
The OPTO-4 is particularly suited to 'noisy' or commercial environments, as it provides a complete solution for system builders who require all components to be shielded. As it is port-powered (from the PC), the OPTO-4 is quick and trouble-free to install.
The unique Actisense design integrates an over-moulded case for excellent water resistance and a small footprint to ease installation into tight spaces.
Features:
NMEA 0183 & RS232 compliant
Full duplex (two-way) communication
All baud rates up to 115200 Baud
Overmoulded case with a narrow profi le for installing in small spaces
Transient protection on the PC output line
Opto-isolation providing 2000 volt protection on the PC input line
Reverse voltage protection on the PC input line
Current limited to protect against cable faults
Port-powered; takes power from the PC port
Fully shielded for superior noise rejection
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
120.71 |
|
|
Standard Support w/4-Way Base - 1.5" Collar
A perfect blend of form and function, Antenna Mounting Systems by Rupp combine good looks with innovative designs. The locking collar holds antenna securely, yet unlocks conveniently for lowering. Made of forged and anodized aluminum for strength and long lasting beauty. Standard supports are designed for easy mounting to cabin sides.
Features:
Base: Oval 4-Way
Spacer: No
Bolts: No
|
169.76 |
|
|
Threaded Antenna Support w/6" Pipe Mount, Oval 4-Way Base & 1.5" Collar
A perfect blend of form and function, Antenna Mounting Systems by Rupp combine good looks with innovative designs. Our locking collar holds the antenna securely, yet unlocks conveniently for lowering. Made of forged and anodized aluminum for strength and long lasting beauty. Threaded mounting packages are ideal for tuna towers and tops.
Features:
Mount Type: Pipe
Base: Oval 4-Way
Pipe: 6"
|
215.65 |
|
|
Threaded Antenna Support w/6" Flat Mount, Oval 4-Way Base & 1.5" Collar
A perfect blend of form and function, Antenna Mounting Systems by Rupp combine good looks with innovative designs. Our locking collar holds the antenna securely, yet unlocks conveniently for lowering. Made of forged and anodized aluminum for strength and long lasting beauty. Threaded mounting packages are ideal for tuna towers and tops.
Features:
Mount Type: Flat
Base: Oval 4-Way
Pipe: 6"
|
215.65 |
|
|
Standard Support w/4-Way Base w/Spacer & 1.5" Collar
A perfect blend of form and function, Antenna Mounting Systems by Rupp combine good looks with innovative designs. The locking collar holds antenna securely, yet unlocks conveniently for lowering. Made of forged and anodized aluminum for strength and long lasting beauty. Standard supports are designed for easy mounting to cabin sides.
Features:
Base: Oval 4-Way
Spacer: 4.5"
Bolts: 2-6"
|
206.47 |
|
|
Multi Purpose Buss Bar - 4 Way 1/4" Studs/150A
Pro Installer Bus bars offer the installer greater flexibility to select buss bars to match their load and space requirements. Compact footprints and modular designs allow for space saving and scalability. Robust construction, thicker copper conductors and additional mounting holes provide the basis for secure, reliable, electrical installations. The covers feature snap-out side skirts providing additional cable entry as required, while the label recess provides the perfect landing for handheld-printer labels. it is easy linking to other Pro Installer products because of the common interconnection height, and the radiused busbbar ends improve cable routing options for large cables.
Bus Type: 4 way
Output screws: 1 x 4
Input studs: 4 x 6 mm (1/4 stud)
Rating (A): 150
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
36.66 |
|
|
Standard 4-Way Junction Box
The OceanLED Standard Junction Box is a robust interconnect module that houses and protects electrical connections. This multi-outlet unit allows up to 4 underwater lights to be connected and is vDC powered. The box provides the transition from conduit to multi-cable via easy cable gland connector.
Features:
12/24v DC
IP66
4x Fused DMX outputs (10a max per output)
Robust Polycarbonate Design
Semi-transparent LID
|
160.69 |
|