Waterproof IP66 DC Battery Charger 10A, 24V Out, 30-80V In, Ruggedized The BCH10 Step Down series of Battery Chargers supply up to 10 amps of charging current at 12, 24, 36 or 48 volts from any higher voltage between 20 and 80 volts DC in an IP66 rated watertight and EMC shielded enclosure for use in automotive, heavy equipment, marine, industrial, rail or alternative energy environments. The output voltage is configured to allow permanent connection to the battery. The standard BCH10W model offers a Deutsch connector on a pigtail input/output cable, and the military grade BCH10MW features separate bayonet style MIL connectors for input and output. The all surface mount high frequency design offers higher reliability, higher efficiency (more than 91%), more power (up to 544 watts at 48 VDC Out) and minimum size. The BCH10MW is rated for operation from -40 to +55 degrees C and has been tested and confirmed to meet MIL-STD-461F for radiated and conducted emissions. It is designed to meet MIL-STD-810G for shock and vibration. The unit has reverse input protection, reverse battery connection protection, output over-voltage protection and features spark free connection to the battery. Smart Ideal Diode output circuitry prevents any reverse current flowing from the battery back into the converter. Features: Watertight O-ring sealed and EMC gasketed enclosure ‘Output ON’ and “Charging” LED indicators Up to 80V input Compact size and easy mounting Deutsch DT04-4P connector on pigtail or MIL connectors Heavy duty ruggedization with wide temperature range Custom output voltages available Custom connector arrangements Input and output EMC filters Two year warranty (parts and labor)

Waterproof IP66 DC Battery Charger 10A, 12V Out, 20-80V In, Ruggedized The BCH10 Step Down series of Battery Chargers supply up to 10 amps of charging current at 12, 24, 36 or 48 volts from any higher voltage between 20 and 80 volts DC in an IP66 rated watertight and EMC shielded enclosure for use in automotive, heavy equipment, marine, industrial, rail or alternative energy environments. The output voltage is configured to allow permanent connection to the battery. The standard BCH10W model offers a Deutsch connector on a pigtail input/output cable, and the military grade BCH10MW features separate bayonet style MIL connectors for input and output. The all surface mount high frequency design offers higher reliability, higher efficiency (more than 91%), more power (up to 544 watts at 48 VDC Out) and minimum size. The BCH10MW is rated for operation from -40 to +55 degrees C and has been tested and confirmed to meet MIL-STD-461F for radiated and conducted emissions. It is designed to meet MIL-STD-810G for shock and vibration. The unit has reverse input protection, reverse battery connection protection, output over-voltage protection and features spark free connection to the battery. Smart Ideal Diode output circuitry prevents any reverse current flowing from the battery back into the converter. Features: Watertight O-ring sealed and EMC gasketed enclosure ‘Output ON’ and “Charging” LED indicators Up to 80V input Compact size and easy mounting Deutsch DT04-4P connector on pigtail or MIL connectors Heavy duty ruggedization with wide temperature range Custom output voltages available Custom connector arrangements Input and output EMC filters Two year warranty (parts and labor)

Waterproof IP66 DC Converter 10A, 24V Out, 30-80V In, Ruggedized The VCH10 Step Down series of Voltage Converters supply up to 10 amps of output current at 12, 24, 36 or 48 volts from any higher voltage between 20 and 80 volts DC in an IP66 rated watertight and EMC shielded enclosure for use in rugged environments. The standard VCH10W model offers a Deutsch connector on a pigtail input/output cable, and the military grade VCH10MW features separate bayonet style MIL connectors for input and output. The all surface mount high frequency design offers higher reliability, higher efficiency (more than 92%), more power (up to 544 watts at 48 VDC Out) and minimum size. The VCH10MW is rated for operation from -40 to +55 degrees C and has been tested and confirmed to meet MIL-STD-461F for radiated and conducted emissions. It is designed to meet MIL-STD-810G for shock and vibration. The unit has reverse input protection, output current limiting and output over-voltage protection. Features: Watertight O-ring sealed and EMC gasketed enclosure MIL connectors ‘Output ON’ and ‘Overload’ LED indicators Compact size and easy mounting Up to 80V input Heavy duty ruggedization with wide temperature range Paralleling diodes Custom output voltages available Two year warranty (parts and labor)

Waterproof IP66 DC Converter 25/35A 12VDC Out/20-45VDC In This single board design incorporates state of the art switchmode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. Extra features include adjustable output voltage, audible and visual indicators for low input voltage, low output voltage, over temperature and overload. Safety features include reverse input protection, over-temperature shutdown, current limiting, short circuit shutdown, a dry contact alarm relay output and output overvoltage crowbar. Optional features include a remote panel monitoring with On-Off control. Features: Ultra-quiet Power sensitive electronics without interference Rugged and reliable to ensure years of safe and trouble free operation Adjustable output voltage Audible & visual indicators for constant current, low input voltage, low output voltage & over-temperature Extremely rugged and well suited for marine and other demanding environments High tolerance for shock and vibration Ultra-quiet low EMI operation Current limiting protection Reverse input protection Output over-voltage crowbar Dry contact output fail relay Remote control option Wide Temperature operation Available Parallel output diodes available Conformal Coating and/or Harsh Environment Ruggedization available Three year parts and labour warranty

Waterproof IP66 DC Converter 10A, 12V Out 20-80V In, Ruggedized The VCH10 Step Down series of Voltage Converters supply up to 10 amps of output current at 12, 24, 36 or 48 volts from any higher voltage between 20 and 80 volts DC in an IP66 rated watertight and EMC shielded enclosure for use in rugged environments. The standard VCH10W model offers a Deutsch connector on a pigtail input/output cable, and the military grade VCH10MW features separate bayonet style MIL connectors for input and output. The all surface mount high frequency design offers higher reliability, higher efficiency (more than 92%), more power (up to 544 watts at 48 VDC Out) and minimum size. The VCH10MW is rated for operation from -40 to +55 degrees C and has been tested and confirmed to meet MIL-STD-461F for radiated and conducted emissions. It is designed to meet MIL-STD-810G for shock and vibration. The unit has reverse input protection, output current limiting and output over-voltage protection. Features: Watertight O-ring sealed and EMC gasketed enclosure MIL connectors ‘Output ON’ and ‘Overload’ LED indicators Compact size and easy mounting Up to 80V input Heavy duty ruggedization with wide temperature range Paralleling diodes Custom output voltages available Two year warranty (parts and labor)

AC Charger 2-Bank, 60A, 24V Out, 110/220 In, IP66 Rated, Ruggedized & Wide Temp The BCA1550 Series battery charger provides up to 1000 watts of charging power to a one or two-bank battery system at 12, 24, 32, 36, 48, or 72 (Rail) VDC from an 85 – 264 VAC source. The BCA1550 Series chargers (BCA) and power supplies (PWS) are designed to supply a DC load or charge a battery at 12, 24, 32, 36, 48, or 72 (Rail) VDC. The 1550 family provides up to 1500 watts of precision power (the 1050 family supplies up to 1000 watts). The 1550 and 1050 families are identical to their previous models (1505 and 1005, respectively) in form, fit, and function as a direct drop-in replacement. Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60Hz with a Power Factor of 0.99 or better from 10% to 100% load. Heavy input filtering reduces EMI to extremely low levels to prevent interference with nearby sensitive electronics. These units are constructed from heavy-duty extruded aluminum chassis and aluminum ventilated front and rear panels with thermostatically controlled cooling fans and all stainless steel fasteners for rugged duty. Reliability features include LED status indicators, input circuit breaker, thermal shutdown, current limiting, reverse polarity connection protection, and output short circuit shutdown with automatic recovery. Features: Power Factor Corrected AC Input Fast and accurate charging Can function as a power supply Visual indicators for operation and errors Five-year parts and labor warranty Specifications: Input Voltage (AC): 85-265 VAC Input Current (Max Amps): 60 A Output Voltage (DC): 24 VDC Nominal Output VDC: 24 VDC Charging Current: 60 A Number of Battery Banks: 2 IP Rating: IP66 Mounting: Panel Approvals: CSA, UL Net Weight: 12 lbs Gross Weight: 12 lbs

AC Charger 2-Bank 55A 24V Out/110/220V In AC Chargers are available as two-stage or two and three-stage chargers capable of charging one or two banks of 12, 16, 24, 28, 32, 36, 48, 72V (rail) or other voltage battery banks, and are designed to quickly and accurately charge and condition batteries.

BatteryLink® Charger - 10Amp - 2-Bank Charge two batteries at or away from the dock with a 10A multistage battery charger and integrated 65A Automatic Charging Relay (ACR) AC charging at the dock: Use AC shore power to charge two isolated battery banks with the 3 Stage 10 Amp battery charger DC charging away from the dock: Share the DC power from the alternator with both the Start and the Auxiliary battery through the integrated 65A ACR Battery Temperature Compensation prolongs battery life Start isolation protects sensitive electronics from voltage sags and spikes Includes LED remote indicator for charge status at the helm Snap-on insulating cover One-piece stainless flange nuts ensure safe and secure connections Specifications Total Output Current: 10A Nominal Voltage: 12V DC Number of Outputs: 1 negative / 2 positive Terminal Stud Torque: 60 in-lb (6.78 Nm) Continuous Rating:65A Intermittent Rating:115A Universal AC Input Voltage: 90-265V AC AC Input Frequency: 50/60Hz Typical Float Voltage:13.5V DC Battery Types: AGM / Flooded / TPPL - Do not mix battery types Cable Size to Meet Ratings:10 AWG Negative Cable / 6 AWG Positive Cable Maximum Battery CCA: 850CCA Maximum Cable Size: 1/0 AWG (50mm) Operating Current: 10mA (No AC Power, ACR Open) / 60mA (No AC Power, ACR Closed) Recommended Battery Bank Sizes: 60Ah Minimum Terminal Stud Size:1/4"-20 (accepts M6 ring terminal) Warranty: 5 Year Combine 30 sec: 13.5V Combine 2 Min: 13.0V Open 10 sec: 12.35V Open 30 sec: 12.75V WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

On-Board Battery Charger 10A / 12V - 1 Bank - 120V Input Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process. Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

On-Board Battery Charger 10A / 12V - 2 Bank - 120V Input Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process. Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sportsman Series Battery Charger - 10A - 1-Bank - 12V Our customers asked for a series of chargers that were smaller, lighter and economically affordable. The Sportsman Series of chargers answers these needs. This line of chargers is designed for all types of battery applications. Sportsman chargers have all the safety and reliability features that have made PRO Charging Systems chargers the #1 choice of most boat manufacturers, dealers and over 750,000 customers across the country. Advanced microprocessors and LED readings make the units even easier to use. Battery Charging System Designed for Use On Land and in Fresh and Salt Water The “Green” Charger: Totally “Repairable” Not a Throw-Away Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Fully Automatic and Totally Waterproof Features: Approved for Wet Cell and AGM batteries Models also available for Gelled Electrolyte batteries Designed for use in fresh and saltwater DeltaVolt® Intuitive Charging Technology Waterproof, dependable, rugged construction Independent outputs Fully automatic / multi stage charging Zero spark technology Battery maintenance mode On-board diagnostic codes Temperature compensated Advanced microprocessor controlled Battery systems available: 12V – 48V LED lights indicate the state of charge Reverse polarity protected No installation restrictions FCC Parts A & B interference compliant DC charge cables = 5' AC power cord = 3' Approved and meets ISO 8846 Marine standards Ignition protected (US Coast Guard 33 CFR 183.410 May be used in many types of sporting applications including: Inland Watercraft Salt Water Watercraft Motorcycles Golf Carts Utility Vehicles… This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

AC Power Supply 10/13A, 24V Out, 85-265V In The PWI320 Intelligent Power Supply delivers a full 300 watts of output power for communications, control or a wide variety of other devices. It is fully Digital Signal Processor controlled and feature Universal Input Voltage from 85 to 265 VAC at 50 or 60 Hz with Active Power Factor Correction for the most efficient use of AC power. The Power Supply is preset to the same voltage as a fully charged battery of the nominal output voltage (ie. 13.6V for a 12V model, etc.). The voltage can be adjusted over a reasonable range using the front panel controls, or the PowerWizard software that is free to download from www.analyticsystems.com. Seven dual color LEDs clearly indicate output current levels as well as indicating faults with the Power Supply. Safety features include Power Supply over temperature shutdown, current limiting, short circuit protection, input under voltage shutdown and output overvoltage protection all with automatic recovery.  PWI320MW model available with MIL connectors, extra input and output filtering and sealed to IP66. Features: Digital Signal Processor controlled Universal worldwide AC input Computer programmable Simple front panel controls Easy connection to loads High Vibration Rugged Duty Dry Contact Output Fail Relay Carrying Handle Canbus / RS232 / Remote Control port Five year parts and labour warranty

Non Iso DC/DC Converter 22A, 24V Out, 11-15V In Step up a 12 VDC battery to between 13.5 and 17.0 or 24.0 and 27.5 DC in 0.5 VDC increments (via 3 position DIP switch), or stabilize a 12 or 24 VDC power system. Safety features include reverse input protection, low input voltage alarm, low output voltage alarm, over temperature shutdown and alarm, a dry contact alarm relay output and output overvoltage crowbar. If the input voltage exceeds the regulated output voltage, the unit simply passes the voltage through with full LC filtering and a single schottky diode drop (0.5 VDC or less). Optional features include remote panel monitoring with On/Off control. Applications include temporarily brightening 12 volt headlights or work lights, increasing voltage into an automotive or marine ignition system for hotter spark and/or prevention of failures due to voltage drop during engine start, stabilizing 12V and 24 VDC power systems in marine, automotive or aeronautical environments and more. Features: Ultra-quiet power sensitive electronics without interference Rugged and reliable to ensure years of safe and trouble free operation Power sensitive electronics without interference Simple operation Paralleling Diodes European ROHS Compliant (Lead Free Manufactured) Electric Fork Lift (Filtering and Surge Suppression) Open Frame (No chassis just heat sink bars) Safety Special Inspection (CSA/UL) Heavy duty ruggedization with wide temperature range Custom input/output available Three year parts and labour warranty

Non Iso DC/DC Converter 13A, 24V Out, 11-15V In Step up a 12 VDC battery to between 13.5 and 17.0 or 24.0 and 27.5 VDC in 0.5 VDC increments (via 3 position DIP switch), or stabilize a 12 or 24 VDC power system. Safety features include reverse input protection, low input voltage alarm, low output voltage alarm, over temperature shutdown and alarm, and output overvoltage crowbar. If the input voltage exceeds the regulated output voltage, the unit simply passes the voltage through with full LC filtering and a single schottky diode drop (0.5 VDC or less). Optional features include a dry contact alarm relay output, and remote panel monitoring with On/Off control. Applications include temporarily brightening 12 volt headlights or work lights, increasing voltage into an automotive or marine ignition system for hotter spark and/or prevention of failures due to voltage drop during engine start, stabilizing 12 and 24 VDC power systems in marine, automotive or aeronautical environments and more.  Features: Ultra-quiet Rugged and reliable to ensure years of safe and trouble free operation Simple operation Current limiting protection Paralleling Diodes European ROHS Compliant (Lead Free Manufactured) Electric Fork Lift (Filtering and Surge Suppression) Open Frame (No chassis just heat sink bars) Safety Special Inspection (CSA/UL) Heavy duty ruggedization with wide temperature range Custom input/output available Three year parts and labour warranty

AC Charger 2-Bank, 60A, 24V Out, 110/220 In, IP66 Rated, Ruggedized & Wide Temp The BCA1550 Series battery charger provides up to 1000 watts of charging power to a one or two-bank battery system at 12, 24, 32, 36, 48, or 72 (Rail) VDC from an 85 – 264 VAC source. The BCA1550 Series chargers (BCA) and power supplies (PWS) are designed to supply a DC load or charge a battery at 12, 24, 32, 36, 48, or 72 (Rail) VDC. The 1550 family provides up to 1500 watts of precision power (the 1050 family supplies up to 1000 watts). The 1550 and 1050 families are identical to their previous models (1505 and 1005, respectively) in form, fit, and function as a direct drop-in replacement. Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60Hz with a Power Factor of 0.99 or better from 10% to 100% load. Heavy input filtering reduces EMI to extremely low levels to prevent interference with nearby sensitive electronics. These units are constructed from heavy-duty extruded aluminum chassis and aluminum ventilated front and rear panels with thermostatically controlled cooling fans and all stainless steel fasteners for rugged duty. Reliability features include LED status indicators, input circuit breaker, thermal shutdown, current limiting, reverse polarity connection protection, and output short circuit shutdown with automatic recovery. Features: Power Factor Corrected AC Input Fast and accurate charging Can function as a power supply Visual indicators for operation and errors Five-year parts and labor warranty Specifications: Input Voltage (AC): 85-265 VAC Input Current (Max Amps): 41 A Output Voltage (DC): 32 VDC Nominal Output VDC: 32 VDC Charging Current: 41 A Number of Battery Banks: 2 IP Rating: IP66 Mounting: Panel Approvals: CSA, UL Net Weight: 12 lbs Gross Weight: 12 lbs