MP Pumps 36095 PMP HHLF2.0PPKC:CC MTR CDI   MP Pumps 36095, HHLF High Head Low Flow Self Priming Centrifugal Pump End Only, 1-1/2" or 2" x 1-1/2" or 2" High Pressure USCG Secifications Auxilary Fire Control HHLF2.0PPK C: CCMTR 1.12 6.5 HR   MP Pumps High Head PumpPak Cast Iron for "C" Face Electric Electric Motor (Less Motor) # 36095. They are shipped with 6.5" maximum diameter impellers for trimming to pumping condition by customer, Bronze construction and will fit Standard NEMA "C" face motors or 184TC NEMA motors. PumPaks are provided less motors and with 6.5" maximum impeller diameters.   Specifications Rated Capacity 140 GPM Maximum Head: 190 feet (82 PSI) Suction & Discharge Connections: 2" X 2" NPT Impeller Diameter: 6.5" maximum diameter impeller. Construction: Cast Iron housing and impeller; Seals - standard carbon, ceramic, viton elastometers, drive sleeve - 304 stainless steel.  Motor Required 5 HP, 3450 rpm Motor Frames Required "C" NEMA motor, or 184TC NEMA motor. Weight: 63 lbs.

MP Pump 28398 Flomax 8 Pumpak SS: Ccmtr7/8 Specifications Rated Capacity 140 GPM Maximum Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft for 7/8" driver shaft; viton mechanical seal. Motors: Pump water end only less motors Motors Required: 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required: Fit 184C/145TC NEMA motors with feet Weight: 49 lbs. Pump Capacity - MP Pumps Flomax 8 Self Priming Pumps At 0 Suction Lift, 3600 RPM Required Motor HPRequired Impeller TrimCapacity At Total Dynamic Head In FeetShut Off 20'30'40'50'60'70'80'90' Gallons Per Minute (GPM) 1-1/24.10"105856020----54' 24.62"12711090704515--74' 35.0"1501401201008060401596'  

MP Pump 28397 Flomax 8 Pumpak SS: Ccmtr5/8 Rated Capacity 140 GPM Maximum Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit 5/8" driver shaft; viton mechanical seal. Motors: Pump water end only less motors Motors Required: 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required: 56C NEMA motors less feet. Weight: 53 lbs. Pump Capacity - MP Pumps Flomax 8 Self Priming Pumps At 0 Suction Lift, 3600 RPM Required Motor HPRequired Impeller TrimCapacity At Total Dynamic Head In FeetShut Off 20'30'40'50'60'70'80'90' Gallons Per Minute (GPM) 1-1/24.10"105856020----54' 24.62"12711090704515--74' 35.0"1501401201008060401596'  

MP Pumps 36083 High Head PumpPak All Bronze 1-1/2" NPT    MP Pumps High Head PumpPak Bronze for "C" Face Electric Motor 1-1/2" NPT (Less Motor) # 36083. They are shipped with 6.5" maximum diameter impellers for trimming to pumping condition by customer, Bronze construction and will fit Standard NEMA "C" face motors or 184TC NEMA motors.   Rated Capacity 140 GPM Maximum Head: 190 feet (82 PSI) Suction & Discharge Connections: 1-1/2" X 1-1/2" NPT  Impeller Diameter: 6.5" maximum diameter impeller.  Construction: Bronze housing and impeller; Seals - standard carbon,  ceramic, viton elastometers, drive sleeve - 304 stainless steel.   

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

MP Pumps 21339 Flomax 8 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 8 Part # MP 21339 Configuration: Pedestal Mount Port Size: 2 in. NPT Flow-Rate: 150 GPM Head Feet: 100   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial   Marine    

MP Pumps 21366 PUMP FM10 C/I 184TC MT Flomax 10 Pumpaks are liquid-ends less power source. Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Cast iron construction and will fit 184C/145TC NEMA motors with feet. PumPaks are provided less motors and with 5" maximum impeller diameters.   Specifications Rated Capacity 140 GPM Maximum Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8" or 7/8" driver shaft; viton mechanical seal.   Pump water end only less motors. Motors Required: 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required: 184C/145TC NEMA motors with feet.

MP Pumps 21383 FM 15 BRONZE PUMP MP Pumps 21383, FLOMAX 15 Self Priming Centrifugal Pump, Wet End Only FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators and Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   3" X 3" NPT Ports Capacity up to 320 GPM Total Head up to 145 feet Bronze construction 5.75 inch diameter impeller

MP Pumps 25979 FM5-CI-56C PUMP   Flomax 5 Pumpaks are liquid-ends less power source. They are shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. They are available in cast iron and all bronze construction and will fit 56C NEMA motors less feet.   Specifications Rated Capacity 100 GPM Maximum Discharge Pressure: 40 PSI Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8" driver shaft; viton mechanical seal. Pump water end only less motors.   Motors Required 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required 56C NEMA motors less feet   

MP Pumps 26074 Flomax 5 C/I MT 7/8"   Flomax 5 Pumpaks are liquid-ends less power source. They are shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. They are available in cast iron and all bronze construction and will fit 184C/145TC NEMA motors with feet.     Specifications Rated Capacity 100 GPM Maximum Discharge Pressure: 40 PSI Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 stainless steel stub shaft to fit either 5/8" or 7/8" driver shaft; viton mechanical seal.   Pump water end only less motors Motors Required 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required 56C NEMA motors less fit or 184C/145TC NEMA motors with feet.

MP Pumps Flomax 5 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 5 Part # MP 21302 Port Size: 1 1/2 in. NPT Flow-Rate: 145 GPM Head Feet: 100   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

MP Pumps 21327 Flomax 8 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 8 part # MP 21327 Port Size: 2 in NPT Flow-Rate: 150 GPM Head Feet: 100     Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine  

MP Pump 28399 Flomax 8 Pump SS: Ped 5.0 MP Pumps Flomax 8, 2" 140 GPM Stainless Steel Pedestal Mount Self Priming Pump 28399 MP Pumps Flomax 8, 2" NPT self priming centrifugal pumps # 28399. Up to 140 GPM, up to 40 PSI (92'), 3450 RPM, all stainless steel construction. Removable flanges and replaceable wear plates protect the housing and eliminate wear. All fasteners are Stainless Steel. Standard mechanical seal have Viton elastomers. Specifications Rated Capacity 140 GPM Maximum Discharge Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Construction: Stainless Steel housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss, weight 49 lbs.; 304 stainless steel stub shaft; viton mechanical seal. Motor: None Pump Capacity - MP Pumps Flomax 8 Self Priming Pumps At 0 Suction Lift, 3600 RPM HPImp.Capacity At Total Dynamic Head In FeetShut Off 20'30'40'50'60'70'80'90' Gallons Per Minute (GPM) 1-1/24.10"105856020----54' 24.62"12711090704515--74' 35.0"1501401201008060401596'  

MP Pumps 21301 Flomax 5 Pump Pak Bronze 3/4 Eng Mnt, 1-1/2" x 1-1/2" FLOMAX 5 self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line. A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Wash-down Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and more.   Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift

FLOMAX®8 by MP Pump part 26079 2" x 2" Self Priming Centrifugal Pump   FLOMAX® 8 self-priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump’s built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX® 8 PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive.   Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wearplate, and a semi-open dynamically balanced impeller.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.