Rubber Seal Protectant - 3.4oz 303 Rubber Seal Protectant is an easy, convenient way to keep the rubber seals of doors, windows conditioned and pliable.  Helps protect against drying and cracking in extreme temperatures, and rejuvenate color and elasticity to old seals, keeping them looking and performing like new!  Features: Conditions rubber seals on doors, windows, hoods and trunks Protects against drying and cracking in extreme temperatures Rejuvenates color to old seals, restores elasticity Made in the U.S.A. *Sold as an Individual  WARNING: This product can expose you to chemicals including Ethylbenzene which is known to the State of California to cause cancer, and Ethylene Glycol which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Rubber Seal Protectant - 3.4oz *Case of 12* 303 Rubber Seal Protectant is an easy, convenient way to keep the rubber seals of doors, windows conditioned and pliable.  Helps protect against drying and cracking in extreme temperatures, and rejuvenate color and elasticity to old seals, keeping them looking and performing like new!  Features: Conditions rubber seals on doors, windows, hoods and trunks Protects against drying and cracking in extreme temperatures Rejuvenates color to old seals, restores elasticity Made in the U.S.A. *Sold as a Case Pack WARNING: This product can expose you to chemicals including Ethylbenzene which is known to the State of California to cause cancer, and Ethylene Glycol which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Rubber Roof Cleaner - 128oz Keep your RV’s rubber roof lasting longer using 303® Rubber Roof Cleaner. With frequent and proper cleaning of your RV’s rubber roof, you can prevent contaminants from becoming embedded in the surface which causes it to degrade over time. 303® Rubber Roof Cleaner is biodegradable, so it’s perfectly safe to rinse it off the roof and siding of an RV. You also do not need to worry about harming the solar panels on the top of your RV either. Simply clean any residue that might get on the panels with water. For the ultimate longevity of your rubber roof, use a coat of 303® Aerospace Protectant after treating with 303® Rubber Roof Cleaner. Features: Cleans and dissolves dirt on rubber roofs on RVs, Campers, Pop-Ups, and Motorhomes Biodegradable and non-abrasive Will not harm solar panels Won’t damage or dry out siding or rubber seals Great for use prior to 303® Aerospace Protectant Directions: Clean and remove any loose dirt and debris on the roof. Add 5 oz. of 303® Rubber Roof Cleaner to a 5-gallon bucket and fill it with clean water. Clean the roof using a scrubbing tool like a brush or mop, cleaning one 3-4 sq. ft. section at a time. Repeat on all sections of the roof, rinsing tools as necessary. After all, sections have been cleaned, rinse the entire roof with a hose and let dry. Never walk on a wet roof. You may also add to an empty spray bottle and spray on the roof instead of mixing it with water in a bucket. Rinse any residual runoff immediately to prevent streaking/water marks from occurring over the sides. 303® Rubber Roof Cleaner will not harm solar panels, however, we do not recommend cleaning solar panels with this product.

Fusion19™ Swimbait Jighead - 5/0L - 3/4oz - Pearl White Berkley Fusion19™ hooks are for everyone, from the novice to the avid angler. The Swimbait Jig Head features an ultra-realistic look and feel with a custom 40-degree pull point for optimal tracking and natural presentation for swimbaits and other soft plastics. With a variety of sizes and hook combinations, the Fusion19 Swimbait Jig Head offers a solution for many bait styles and sizes. Each package provides ideal bait recommendations.  Features: Needlepoint for easier penetration High-definition detail for a realistic look Conical bait keeper with wire locks baits into place Custom 40-degree hooks for an ideal pull point for a natural presentation Forged hook for increased lateral strength Optimal head design for a variety of Berkley soft plastics The package features innovative resealable clam for tackle management Specifications: Color: Pearl White Hook Size: 5/0L Tackle Size: 3/4oz/21g Package Count: 3

Fusion19™ Swimbait Jighead - 5/0L - 3/4oz - Red Berkley Fusion19™ hooks are for everyone, from the novice to the avid angler. The Swimbait Jig Head features an ultra-realistic look and feel with a custom 40-degree pull point for optimal tracking and natural presentation for swimbaits and other soft plastics. With a variety of sizes and hook combinations, the Fusion19 Swimbait Jig Head offers a solution for many bait styles and sizes. Each package provides ideal bait recommendations.  Features: Needlepoint for easier penetration High-definition detail for a realistic look Conical bait keeper with wire locks baits into place Custom 40-degree hooks for an ideal pull point for a natural presentation Forged hook for increased lateral strength Optimal head design for a variety of Berkley soft plastics The package features innovative resealable clam for tackle management Specifications: Color: Red Hook Size: 5/0L Tackle Size: 3/4oz/21g Package Count: 3

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

Silicone Rubber Sealant Cartridge - Clear An all-purpose, non-corrosive, non-yellowing, mildew resistant, low-odor, 100% marine high quality silicone sealant. Tack-free in 30 minutes or less. *Fully cured in 24 hours. For use above or below the waterline. Will not shrink, crack, or dry out. Superior flexibility and adhesion to fiberglass, plastic, metal, and wood. Retains flexibility and tensile strength even after years of exposure. Acid free cure will not corrode metal.

Silicone Rubber Sealant Cartridge - White An all-purpose, non-corrosive, non-yellowing, mildew resistant, low-odor, 100% marine high quality silicone sealant. Tack-free in 30 minutes or less. *Fully cured in 24 hours. For use above or below the waterline. Will not shrink, crack, or dry out. Superior flexibility and adhesion to fiberglass, plastic, metal, and wood. Retains flexibility and tensile strength even after years of exposure. Acid free cure will not corrode metal.

Silicone Rubber Sealant Cartridge - Black An all-purpose, non-corrosive, non-yellowing, mildew resistant, low-odor, 100% marine high quality silicone sealant. Tack-free in 30 minutes or less. *Fully cured in 24 hours. For use above or below the waterline. Will not shrink, crack, or dry out. Superior flexibility and adhesion to fiberglass, plastic, metal, and wood. Retains flexibility and tensile strength even after years of exposure. Acid free cure will not corrode metal.

G4 Back Pin 0.9" (23mm) LED Light" G4 utilizes High Power LEDs for more than enough light to read and work by. As with all our replacement bulbs the G4 includes a built in Buck Regulator, which produces little heat, making it the most robust on the market today. Compact size Long Life: Up to 50,000 Hours No Fire Hazard Like Halogens

G4 Back Pin 0.9" (23mm) LED Light" G4 utilizes High Power LEDs for more than enough light to read and work by. As with all our replacement bulbs the G4 includes a built in Buck Regulator, which produces little heat, making it the most robust on the market today. Compact size Long Life: Up to 50,000 Hours No Fire Hazard Like Halogens

SS175H-W/0 Stainless Steel Thru-Hull Transducer - 0° - 9-Pin The SS175H-W is a stainless steel, thru-hull CHIRP transducer, ideal for sportfishing and commercial vessels up to 8M (25') in size. This single-channel transducer offers High CHIRP combined with a wide beam for the best resolution and coverage in shallower depths. Features: 130-210 kHz High CHIRP with wide 25° beam for excellent fish targets  Up to 310M (1000') range with High CHIRP 1 internal broadband ceramic Thru-hull with stainless steel housing Suitable for fiberglass and wood hulls Ideal for sportfishing and commercial vessels up to 8M (25') Recommended for use with Simrad NSSevo3 Lowrance HDS Gen3 multifunction displays

Constant Torque Hinge Symmetric Forward Torque 0.9 N-m - Reverse Torque 0.9 N-m - Large Size - Stainless Steel 316 - Polished Southco’s line of Constant Torque Position Control Hinges provide constant resistance throughout the entire range of motion, enabling users to easily position doors, display screens, and other mounted components and hold them securely at any desired angle – fully opened, fully closed, or anywhere in between. Hinges are available in a wide variety of sizes, materials, and torque ranges to satisfy application needs across industries. Specifications: Material: 316 Stainless Steel Finish: Polished Color/Appearance: Polished Forward Torque (Nm): 0.90 Reverse Torque (Nm): 0.90 Access Restriction: No Restriction Torque Type: Symmetric Mounting Style: Screw Mount Installation: Rivet/Screw Series: 400 Series Size Series: Large Size Class: E6/ST - Constant Torque Position Control Hinges

Replacement Vinyl Insert - 0° - 9" - Black Replacement vinyl insert for 9" rod holders

Replacement Vinyl Insert - 0° - 9" - White Replacement vinyl insert for 9" rod holders