Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4222 Cast Iron Convertible Jet Pump 3/4 HP Cast iron convertible jet pumps can be used in shallow or deep well applications in " diameter wells or larger and are pre-set for 30-50 PSI operation. KEY FEATURES Superior performance at depths to water of 100' or less Rugged, heavy-duty pump housing Ready-to-install 230 volt motor - see manual for 115 volt conversion Pressure switch pre-wired with 30-50 PSI pressure setting WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11.9 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  10.8 GPM (shallow setup) MAX LIFT:  25' w/ shallow setup / 100' w/ deep well setup MAXIMUM PRESSURE:  60 psi w/ shallow setup / 54 psi w/ deep setup PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less. KEY FEATURES Superior performance at depths to water of 25' or less Rugged, heavy-duty cast iron pump housing Ready-to-install dual voltage (115v/230v) motor 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8.8 GPM FLOW AT 10' LIFT and 40 PSI:  7.8 GPM MAX PSI:  56 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT MINIMUM SUCTION PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.4 amps VOLTAGE:  115v/230v (preset to 115v), 60 Hz RECOMMENDED BREAKER:  15 amp LIQUID TEMP RANGE:  32°F-140 °F (0°C-60 °C) JET KIT:  included

Flotec FP4112-08 Cast Iron Shallow Well Jet Pump 1/2 HP Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.   KEY FEATURES Superior performance at depths to water of 25' or less Rugged, heavy-duty cast iron pump housing Ready-to-install dual voltage (115v/230v) motor 1-1/4" NPT suction and 1" NPT discharge pipe sizes   WARRANTY 1 year limited warranty   BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8.8 GPM FLOW AT 10' LIFT and 40 PSI:  7.8 GPM MAX PSI:  56 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT MINIMUM SUCTION PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.4 amps VOLTAGE:  115v/230v (preset to 115v), 60 Hz RECOMMENDED BREAKER:  15 amp LIQUID TEMP RANGE:  32°F-140 °F (0°C-60 °C) JET KIT:  included ACCESSORIES INCLUDED:  none

Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4832 Shallow Well Jet Pump 1HP Flotec Shallow Well Jet Pump Stainless Steel Construction 1HP 115/230V 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 18.4GPM at 40psi Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec N76-46P Pump Body This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.   Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.   The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.

Flotec FP4212 Cast Iron Convertible Jet Pump 1/2 HP KEY FEATURES Superior performance at depths to water of 100' or less Rugged, heavy-duty pump housing Ready-to-install dual-voltage 115v/230v motor - see manual for 230 volt conversion Pressure switch pre-wired with 30-50 PSI pressure setting WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  7.9 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  7.1 GPM (shallow setup) MAX LIFT:  25' for shallow setup / 70' for deep setup MAXIMUM PRESSURE:  60 psi (shallow setup) / 54 psi (deep setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1"NPT AMP DRAW (full load):  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4432 Vertical Deep Well Jet Pump 1 HP Vertical deep well jet pump can be used in 4" diameter or larger wells up to 260', or in 2" diameter wells up to 180'. KEY FEATURES Superior performance at depths to water of 50' or more Rugged, heavy-duty cast iron pump housing Ready-to-install 230 volt motor - see manual for 115 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1 MAXIMUM CAPACITY:  12 GPM FLOW AT 50' LIFT and 40 PSI:  11 GPM MAX LIFT:  260' for 4" or larger well / 180' for 2" well PRESSURE SWITCH SETTING:  40/60 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.6 amps on 230v / 19.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v MAXIMUM WATER TEMPERATURE:  140 F (60 C)

FP4432 Overhaul Kit   Use for Flotec model FP4432 deep well jet pump Includes impeller, diffuser, and all needed seals and gaskets Restores like-new performance

Simer 2810E-02 Shallow Well Jet Pump, 3/4HP Simer Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230 Volt Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, Best for Shallow Wells to 20 Feet, Maximum Lift 25 Feet, up to 14.4GPM, Adjustable Pressure Switch Set to 30psi On / 50psi Off

Sta-Rite PND-10 Shallow Well Jet Pump 3/4HP Sta-Rite Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 10.3GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Sta-Rite PWP-01 Shallow Well Jet Pump 3/4HP Sta-Rite Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 10.3GPM at 40psi, No Pressure Switch, up to 25 Foot Water Depth

Simer 3107P Shallow Well Jet Pump, 3/4HP Simer Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 3/4HP 115/230V Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 10.3GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  9 GPM (shallow well setup) FLOW AT 10' LIFT and 40 PSI:  7.8 GPM (shallow well setup) MAX LIFT:  25' w/ shallow well jet kit / 70' w/ deep well jet kit MAX PSI:  62 psi (shallow well setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" MINIMUM SUCTION PIPE SIZE:  1-1/4" DRIVE PIPE SIZE:  1" DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)