Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1 MAXIMUM CAPACITY:  20.7 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  18.3 GPM (shallow setup) MAX LIFT:  25' for shallow setup / 90' for deep setup MAXIMUM PRESSURE:  52 psi for shallow / 56 psi for deep PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW:  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

FP4432 Overhaul Kit   Use for Flotec model FP4432 deep well jet pump Includes impeller, diffuser, and all needed seals and gaskets Restores like-new performance

Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  9 GPM (shallow well setup) FLOW AT 10' LIFT and 40 PSI:  7.8 GPM (shallow well setup) MAX LIFT:  25' w/ shallow well jet kit / 70' w/ deep well jet kit MAX PSI:  62 psi (shallow well setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" MINIMUM SUCTION PIPE SIZE:  1-1/4" DRIVE PIPE SIZE:  1" DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less. KEY FEATURES Superior performance at depths to water of 25' or less Rugged, heavy-duty cast iron pump housing Ready-to-install dual voltage (115v/230v) motor 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8.8 GPM FLOW AT 10' LIFT and 40 PSI:  7.8 GPM MAX PSI:  56 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT MINIMUM SUCTION PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.4 amps VOLTAGE:  115v/230v (preset to 115v), 60 Hz RECOMMENDED BREAKER:  15 amp LIQUID TEMP RANGE:  32°F-140 °F (0°C-60 °C) JET KIT:  included

Flotec FP4832 Shallow Well Jet Pump 1HP Flotec Shallow Well Jet Pump Stainless Steel Construction 1HP 115/230V 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 18.4GPM at 40psi Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4112-08 Cast Iron Shallow Well Jet Pump 1/2 HP Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.   KEY FEATURES Superior performance at depths to water of 25' or less Rugged, heavy-duty cast iron pump housing Ready-to-install dual voltage (115v/230v) motor 1-1/4" NPT suction and 1" NPT discharge pipe sizes   WARRANTY 1 year limited warranty   BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8.8 GPM FLOW AT 10' LIFT and 40 PSI:  7.8 GPM MAX PSI:  56 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT MINIMUM SUCTION PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.4 amps VOLTAGE:  115v/230v (preset to 115v), 60 Hz RECOMMENDED BREAKER:  15 amp LIQUID TEMP RANGE:  32°F-140 °F (0°C-60 °C) JET KIT:  included ACCESSORIES INCLUDED:  none

Flotec FP4105 Cast Iron Jet Pump 1/2 HP New cast iron shallow well jet pump is ideal for wells with pumping levels of 25' or less. Self-priming after the pump housing is initially filled with water. KEY FEATURES Reliable performance at 25' depth to water or less Maximum pressures of 63 PSI and maximum pumping capacities to 5.1 GPM Pump housing is constructed of heavy-duty cast iron and is ready to install 115 volt 1/2 HP Fan cooled, completely enclosed motor 1" Suction Port and 1" Discharge Port WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  5.6 GPM FLOW at 10' LIFT and 40 PSI:  4.5 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  63 PSI PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  7.2 amps VOLTAGE:  115v, 60 Hz RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP5532 Cast Iron Centrifugal Pump 1 HP Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling. FEATURES Superior performance at depths to water of 25' or less Rugged, heavy-duty cast iron pump housing Maximum pumping capacities to 68 GPM Ready-to-install 230 volt motor (dual voltage) 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1 MAXIMUM CAPACITY:  47 GPM MAXIMUM LIFT:  25' MAXIMUM DISCHARGE PRESSURE:  49 psi MAXIMUM INLET PRESSURE:   MAXIMUM TOTAL PRESSURE:   SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v , 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v LIQUID TEMP RANGE:  140 °F (60 °C)  

Flotec FP5230 Cast Iron Sprinkler Pump 1 HP Powerful 1 HP cast iron sprinkler pump moves up to 45 gpm. Perfect for sprinkler systems or water transfer applications. FEATURES Superior performance at depths-to-water of 25' or less Ideal for larger sprinkler systems and water transfer Rugged cast iron construction Voltage-selectable to run on 115v or 230v 1 year limited warranty BODY CONSTRUCTION: Cast Iron HORSEPOWER: 1 MAXIMUM CAPACITY: 45 GPM FLOW at 10' LIFT and 30 PSI: 35 GPM MAX LIFT:  25' MAXIMUM PRESSURE: 50 psi SUCTION PIPE SIZE: 1-1/4" NPT DISCHARGE PIPE SIZE: 1" NPT AMP DRAW (full load): 8.8 amps on 230v / 16.6 amps on 115v VOLTAGE: 230v / 115v , 60 Hz RECOMMENDED BREAKER: 15 amp on 230v / 25 amp on 115v MAXIMUM WATER TEMPERATEURE: 140 F (60 C)

Flotec N76-46P Pump Body This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.   Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.   The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.

Flotec FP4855 Shallow Well Jet Kit Ejector Jet Package converts FP4200 series convertible jet pumps for use with shallow well

Flotec FP4875 Shallow Well Jet Kit Use on FP4300 series Flotec convertible jet pump Bolts to nose of pump to convert for shallow well use

Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years. KEY FEATURES Superior performance at depths to water of 25' or less Heavy-duty, stainless steel pump housing for highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11 GPM FLOW at 10' LIFT and 40 PSI:  11 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  52 psi MAXIMUM INLET PRESSURE:   PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v MAXIMUM WATER TEMPERATURE:  122°F (50 °C)

Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)