|
Flotec FP4212 Cast Iron Convertible Jet Pump 1/2 HP
KEY FEATURES
Superior performance at depths to water of 100' or less
Rugged, heavy-duty pump housing
Ready-to-install dual-voltage 115v/230v motor - see manual for 230 volt conversion
Pressure switch pre-wired with 30-50 PSI pressure setting
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 7.9 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 7.1 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 70' for deep setup
MAXIMUM PRESSURE: 60 psi (shallow setup) / 54 psi (deep setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"NPT
AMP DRAW (full load): 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
509.25 |
|
|
Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor - see manual for 115 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 20.7 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 18.3 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 90' for deep setup
MAXIMUM PRESSURE: 52 psi for shallow / 56 psi for deep
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW: 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
698.25 |
|
|
Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP
This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8 GPM
FLOW at 10' LIFT and 40 PSI: 6.4 GPM
MAX LIFT: 25'
MAX PRESSURE: 77 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.4 amps
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
432.90 |
|
|
Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP
Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.
KEY FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install dual voltage (115v/230v) motor
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8.8 GPM
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM
MAX PSI: 56 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
MINIMUM SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.4 amps
VOLTAGE: 115v/230v (preset to 115v), 60 Hz
RECOMMENDED BREAKER: 15 amp
LIQUID TEMP RANGE: 32°F-140 °F (0°C-60 °C)
JET KIT: included
|
433.55 |
|
|
Flotec FP4105 Cast Iron Jet Pump 1/2 HP
New cast iron shallow well jet pump is ideal for wells with pumping levels of 25' or less. Self-priming after the pump housing is initially filled with water.
KEY FEATURES
Reliable performance at 25' depth to water or less
Maximum pressures of 63 PSI and maximum pumping capacities to 5.1 GPM
Pump housing is constructed of heavy-duty cast iron and is ready to install
115 volt 1/2 HP
Fan cooled, completely enclosed motor
1" Suction Port and 1" Discharge Port
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 5.6 GPM
FLOW at 10' LIFT and 40 PSI: 4.5 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 63 PSI
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.2 amps
VOLTAGE: 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
381.42 |
|
|
Flotec FP4112-08 Cast Iron Shallow Well Jet Pump 1/2 HP
Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.
KEY FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install dual voltage (115v/230v) motor
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8.8 GPM
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM
MAX PSI: 56 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
MINIMUM SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.4 amps
VOLTAGE: 115v/230v (preset to 115v), 60 Hz
RECOMMENDED BREAKER: 15 amp
LIQUID TEMP RANGE: 32°F-140 °F (0°C-60 °C)
JET KIT: included
ACCESSORIES INCLUDED: none
|
465.00 |
|
|
Flotec FP4222 Cast Iron Convertible Jet Pump 3/4 HP
Cast iron convertible jet pumps can be used in shallow or deep well applications in " diameter wells or larger and are pre-set for 30-50 PSI operation.
KEY FEATURES
Superior performance at depths to water of 100' or less
Rugged, heavy-duty pump housing
Ready-to-install 230 volt motor - see manual for 115 volt conversion
Pressure switch pre-wired with 30-50 PSI pressure setting
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 3/4
MAXIMUM CAPACITY: 11.9 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 10.8 GPM (shallow setup)
MAX LIFT: 25' w/ shallow setup / 100' w/ deep well setup
MAXIMUM PRESSURE: 60 psi w/ shallow setup / 54 psi w/ deep setup
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 6.1 amps on 230v / 12.2 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
68.64 |
|
|
Flotec FPPM3600D Thermoplastic Pedestal Sump Pump 1/3 HP
The pedestal design is engineered for the easy installation and replacement of most other brands of pedestal pumps.
FEATURES
Replaces any existing brand of 1/3 HP pedestal pump
Long lasting thermoplastic construction
Quick, easy installation
Fits in a 12" diameter basin and offers a 1-1/4" discharge
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/3
MAXIMUM CAPACITY: 3000 GPH
FLOW AT 10' LIFT: 2460 GPH
SWITCH TYPE: Vertical
SWITCH ON LEVEL: 10-1/2"
SWITCH OFF LEVEL: 2-1/2"
MINIMUM SUMP DIAMETER: 12"
MINIMUM SUMP DEPTH: 12"
DISCHARGE PIPE SIZE: 1-1/4" FNPT
MINIMUM PIPE SIZE: 1-1/4"
MAXIMUM SOLID HANDLING SIZE:
CORD LENGTH: 6'
AMP DRAW: 3.5 amps
VOLTAGE: 115V, 60 HZ
RECOMMENDED BREAKER: 15 amps
LIQUID TEMP RANGE: 32°F to 70°F(0°-21°C)
|
178.62 |
|
|
Flotec FPZS50T Submersible Thermoplastic Sump Pump
Flotec's 1/2 HP sump pump with energy-efficient design that produces high-output performance. Constructed from engineered composites providing dependable, corrosion-resistant service for years to come. Tethered on/off float switch.
Thermoplastic construction - resists corrosion
Zinc motor housing - dissipates heat quickly and extends motor life
Stainless steel fasteners and hardware - for long life
Smooth Flow Hydraulics - delivers high performance for demanding applications
Switch Type: Tethered - Operates in 14" basins or larger
Horse Power: 1/2 HP
GPH: 4,200
Max Lift: 22'
Solids Handling: 3/16"
Discharge: 1/5" NPT
Power Cord: 8', Grounded
|
286.26 |
|
|
Flotec FPZS50V Submersible Thermoplastic Sump Pump 1/2 HP
Flotec's 1/2 HP sump pump with energy-efficient design that produces high-output performance. Constructed from engineered composites providing dependable, corrosion-resistant service for years to come. Vertical on/off float switch can be used in smaller sump basins.
FEATURES
Thermoplastic construction - resists corrosion
Zinc motor housing - dissipates heat quickly and extends motor life
Stainless steel fasteners and hardware - for long life
Smooth Flow Hydraulics - delivers high performance for demanding applications
1 Year Limited Warranty
Switch Type: Vertical - Operates in 10" basins or larger
Horse Power: 1/2 HP
GPH: 4,200
Max Lift: 22'
Solids Handling: 3/16"
Discharge: 1.5" NPT
Power Cord: 8', Grounded
|
296.40 |
|
|
Flotec FPSE3601A Cast Iron Sewage Pump 1/2 HP
Rugged, sewage and effluent pumps are capable of handling solids up to 2". Available in cast iron design for a variety of wastewater applications.
Heavy-duty, rugged cast iron automatic submersible sewage pump
Capable of handling 2" solids - ideal for basement installations, pumping below grade toilets, laundry facilities, underground parking, grain storage and construction sites
Includes by-pass float switch for automatic or manual operation
BODY CONSTRUCTION: CAST IRON
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9000 GPH
FLOW AT 10' LIFT: 5400 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2" NPT
MINIMUM PIPE SIZE: 2" for sewage applications / 1-1/2" for effluent applications
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 10'
AMP DRAW: 13 amps
VOLTAGE: 115v. 60 Hz
RECOMMENDED BREAKER: 20 amp
|
699.00 |
|
|
Flotec FP5512 Cast Iron Centrifugal Pump 1/2 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install 230 volt motor (dual voltage)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 22 GPM
MAX LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 36 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 4.7 amps on 230v / 9.4 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
RECOMMENDED BREAKER: 15 amp on 230v / 15 amp on 115v
|
440.70 |
|
|
Flotec FPP1511-P2 Overhaul Kit
Use with model FP4312 convertible jet pump
Includes impeller, diffuser, and all seals and gaskets required to overhaul pump
Restores like-new performance
|
85.54 |
|
|
Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP
This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 3/4
MAXIMUM CAPACITY: 12 GPM
FLOW at 10' LIFT and 40 PSI: 9.7 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 78 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 6.1 amps on 230v / 12.2 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
511.50 |
|
|
Flotec FP4855 Shallow Well Jet Kit
Ejector Jet Package converts FP4200 series convertible jet pumps for use with shallow well
|
103.74 |
|