Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years. KEY FEATURES Superior performance at depths to water of 25' or less Heavy-duty, stainless steel pump housing for highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11 GPM FLOW at 10' LIFT and 40 PSI:  11 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  52 psi MAXIMUM INLET PRESSURE:   PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v MAXIMUM WATER TEMPERATURE:  122°F (50 °C)

Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  9 GPM (shallow well setup) FLOW AT 10' LIFT and 40 PSI:  7.8 GPM (shallow well setup) MAX LIFT:  25' w/ shallow well jet kit / 70' w/ deep well jet kit MAX PSI:  62 psi (shallow well setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" MINIMUM SUCTION PIPE SIZE:  1-1/4" DRIVE PIPE SIZE:  1" DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4432 Vertical Deep Well Jet Pump 1 HP Vertical deep well jet pump can be used in 4" diameter or larger wells up to 260', or in 2" diameter wells up to 180'. KEY FEATURES Superior performance at depths to water of 50' or more Rugged, heavy-duty cast iron pump housing Ready-to-install 230 volt motor - see manual for 115 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1 MAXIMUM CAPACITY:  12 GPM FLOW AT 50' LIFT and 40 PSI:  11 GPM MAX LIFT:  260' for 4" or larger well / 180' for 2" well PRESSURE SWITCH SETTING:  40/60 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.6 amps on 230v / 19.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec N76-46P Pump Body This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.   Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.   The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.

Flotec FP4122 Well Pump 3/4Hp 115/230V Flotec Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 14.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4832 Shallow Well Jet Pump 1HP Flotec Shallow Well Jet Pump Stainless Steel Construction 1HP 115/230V 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 18.4GPM at 40psi Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

FP4432 Overhaul Kit   Use for Flotec model FP4432 deep well jet pump Includes impeller, diffuser, and all needed seals and gaskets Restores like-new performance

Sta-Rite SNC-L Shallow Well Jet Pump 1/2HP 1/2 HP - 115/230 Volt - Shallow Well Jet Pump The ProJet SN Series Pumps provide excellent performance with good pressure for wells to 25 feet deep. Self-priming after the priming chamber has been filled with water. APPLICATIONS Water systems and sprinkling   FEATURES Quality Construction Close grained cast iron body. Drain port provided for easy winterizing. Built-in Jet High strength Lexan nozzle and venturi for maximum resistance to corrosion and abrasion. Clean out plug provided for ease of service. Noryl Impeller Precision-molded for perfect balance ultra-smooth for highest performance and efficiency. Precision Molded Diffuser Pump primes faster, handles more air, with multi-port, precision-molded, reinforced polypropylene diffuser. Mechanical Shaft Seal Precision lapped and highly polished carbonceramic, stainless steel construction. Internal design guarantees continuous water lubrication. Motor Windings Superior insulation materials protect against excessive moisture and contaminants assure prolonged motor life. Balanced Rotor Die cast under high pressures for uniform performance and greater efficiency, dynamically balanced. Heavy-duty Ball Bearings Shielded, permanently lubricated bearings, extensively tested to ensure extended life and smooth, quiet operation. Pump and Motor Shaft Stainless steel for maximum corrosion resistance; one-piece threaded shaft for positive impeller drive and alignment. Dustproof Cover All electrical components are protected from dirt, dust and insects by a dustproof canopy; ventilating air cannot contaminate vital switching components. Pressure Switch Professional quality, allows cut-in adjustments. SPECIFICATIONS Max. Liquid Temperature: 140°F Max. Inlet Pressure: 50 PSI

Flotec FPSC1725X-03 Cast Aluminum Water Removal Utility Pump 1/4 HP 1250 GPH Cast Aluminum construction provides years of service for those emergency water removal situations. FEATURES Heavy-duty, epoxy coated, cast aluminum construction Portable pump for emergency water removal or emptying shallow flooded areas Draws water down to 1/8" Switch for automatic operation sold separately 3-year limited warranty BODY CONSTRUCTION:  Cast Aluminum HORSEPOWER:  1/4 HP MAXIMUM CAPACITY:  1320 GPH FLOW AT 10' LIFT:  1020 GPH DISCHARGE SIZE:  1¼" (male) NPT VOLTAGE:  115v AC, 60 Hz CORD LENGTH:  8' with 3-prong grounded plug MAXIMUM WATER TEMPERATURE:  120°F (50°C)

Simer 2800 Shallow Well Jet Pump, 1/2HP Simer Shallow Well Jet Pump, Cast Iron Construction, 1/2HP TEFC Motor 115Volt only, 1” NPT Ports, up to 5.1GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Simer 2805E-02 Shallow Well Jet Pump, 1/2HP Simer Shallow Well Jet Pump, Cast Iron Construction, 1/2HP 115/230Volt Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, Best for Shallow Wells to 20 Feet, Maximum Lift 25 Feet, up to 8.5GPM, Adjustable Pressure Switch Set to 30psi On / 50psi

Sta-Rite PNC-10 Shallow Well Jet Pump 1/2HP Sta-Rite Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1/2HP 115/230V, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 7GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Simer 3105P Shallow Well Jet Pump, 1/2HP Simer Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1/2HP 115/230V Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 7.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth