|
3" Clamp Insert - 1.9" Inner Diameter
This clamp insert is to change the fitting size to the tower for the Roswell 3′′ clamps.
Specifications:
Inner Diameter: 1.9 in.
Material: Nylon
|
12.00 |
|
|
3" Clamp Insert - 2.5" Inner Diameter
This clamp insert is to change the fitting size to the tower for the Roswell 3′′ clamps.
Specifications:
Inner Diameter: 2.5 in.
Material: Nylon
|
12.00 |
|
|
3" Clamp Insert - 2.25" Inner Diameter
This clamp insert is to change the fitting size to the tower for the Roswell 3′′ clamps.
Specifications:
Inner Diameter: 2.25 in.
Material: Nylon
|
12.00 |
|
|
3" Clamp Insert - 2.85" Inner Diameter
This clamp insert is to change the fitting size to the tower for the Roswell 3′′ clamps.
Specifications:
Inner Diameter: 2.85 in.
Material: Nylon
|
12.00 |
|
|
3" Clamp Insert - 2" Inner Diameter
This clamp insert is to change the fitting size to the tower for the Roswell 3′′ clamps.
Specifications:
Inner Diameter: 2 in.
Material: Nylon
|
12.00 |
|
|
Primer Bulb - 1/4" Inner Diameter Hose
This Atwood Primer Bulb is engineered and constructed to deliver the most reliable priming and long-term leak-free performance. The exclusive three-layer construction prevents collapse under vacuum and prevents ballooning or bursting under pressure. The low-permeation material prevents fuel evaporation, and this bulb delivers 60 percent more output per pump than leading competitors.
Features:
It is intended for use with a 1/4-inch interior diameter hose
Exclusive high-efficiency check-valves deliver faster priming and low fuel restriction (less than 1kPa restriction at 50 liters/hour)
Engineered hose barbs and stainless steel stepless clamps ensure leak-free performance
This bulb is compatible with Ethanol blended fuels, and it is EPA and CARB certified
|
19.30 |
|
|
Stainless Steel Thru-Hull Short Straight Barbed - 1-1/8" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Short Thread is a more compact size, which allows installation near corners and in confined areas
Specifications:
Hose size: (inch) 1-1/8" inner diameter
Flange Diameter: (inch) 2-1/4"
Thread O.D. (outside diameter): (inch) 1-3/8"
Thread Length: (inch) 1-1/4"
Barb Length: (inch) 1"
Total Length: (inch) 2-1/2"
Install Hole Saw Size: (inch) 1-1/2"
Thread NPSM: (inch) 1"
Max Hull Thickness: (inch) 5/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
29.50 |
|
|
Stainless Steel Thru-Hull Short Straight Barbed - 1-1/4" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Short Thread is a more compact size, which allows installation near corners and in confined areas
Specifications:
Hose size: (inch) 1-1/4" inner diameter
Flange Diameter: (inch) 2-1/4"
Thread O.D. (outside diameter): (inch) 1-5/8"
Thread Length: (inch) 1-1/4"
Barb Length: (inch) 1"
Total Length: (inch) 2-5/8"
Install Hole Saw Size: (inch) 1-3/4"
Thread NPSM: (inch) 1-1/4"
Max Hull Thickness: (inch) 5/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
38.69 |
|
|
Stainless Steel Thru-Hull Short Straight Barbed - 1-1/2" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Short Thread is a more compact size, which allows installation near corners and in confined areas
Specifications:
Hose size: (inch) 1-1/2" inner diameter
Flange Diameter: (inch) 3"
Thread O.D. (outside diameter): (inch) 1-7/8"
Thread Length: (inch) 1-1/4"
Barb Length: (inch) 1-1/2"
Total Length: (inch) 3-1/8"
Install Hole Saw Size: (inch) 2"
Thread NPSM: (inch) 1-1/2"
Max Hull Thickness: (inch) 5/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
44.12 |
|
|
Stainless Steel Thru-Hull Standard Straight Barbed - 1-1/8" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Standard Thread model has a full-length thread for thick hulls and easy tightening
Specifications:
Hose size: (inch) 1-1/8" inner diameter
Flange Diameter: (inch) 2-1/4"
Thread O.D. (outside diameter): (inch) 1-3/8"
Thread Length: (inch) 2-3/8"
Barb Length: (inch) 1-1/4"
Total Length: (inch) 3-7/8"
Install Hole Saw Size: (inch) 1-1/4"
Thread NPSM: (inch) 1"
Max Hull Thickness: (inch) 1-3/4"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
29.40 |
|
|
Stainless Steel Thru-Hull Standard Straight Barbed - 1-1/4" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Standard Thread model has a full-length thread for thick hulls and easy tightening
Specifications:
Hose size: (inch) 1-1/4" inner diameter
Flange Diameter: (inch) 2-1/4"
Thread O.D. (outside diameter): (inch) 1-5/8"
Thread Length: (inch) 2-1/2"
Barb Length: (inch) 1-1/4"
Total Length: (inch) 4-1/4"
Install Hole Saw Size: (inch) 1-3/4"
Thread NPSM: (inch) 1-1/4"
Max Hull Thickness: (inch) 1-7/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
37.92 |
|
|
Stainless Steel Thru-Hull Standard Straight Barbed - 1-1/2" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Standard Thread model has a full-length thread for thick hulls and easy tightening
Specifications:
Hose size: (inch) 1-1/2" inner diameter
Flange Diameter: (inch) 3"
Thread O.D. (outside diameter): (inch) 1-7/8"
Thread Length: (inch) 2-1/2"
Barb Length: (inch) 1-1/4"
Total Length: (inch) 4-1/8"
Install Hole Saw Size: (inch) 2"
Thread NPSM: (inch) 1-1/2"
Max Hull Thickness: (inch) 1-7/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
42.83 |
|
|
White Plastic 90 Degree Thru-Hull Connector - 1-1/8" Inner Diameter
90° Thru-Hulls are ideal for tight installations, such as livewell overflow drains. The angled design also eliminates hose kinking.
Specifications:
Fits Hose Size: (inch) 1-1/8"inner diameter
Max Hull Thickness: (inch) 1-7/8"
Flange Diameter: (inch) 2-7/16"
Installation Hole Size: (inch) 1-5/16"
Drain Plug: (inch) 7/8"
Color: White
*Plastic Thru-Hull Connectors are designed for installation above the water line only
|
11.71 |
|
|
White Plastic Thru-Hull Fitting - 1-1/8" Inner Diameter
This thru-hull fitting is made with a durable, thermoplastic construction, which prevents electrolysis.
Specifications:
Hose Size: (inch) 1-1/8" Inner diameter
Stem Length: (inch) 3-1/4"
Max Hull Thickness: (inch) 1-1/4"
Flange Diameter: (inch) 2-1/4"
Installation Hole Size: (inch) 1-3/8"
Drain Plug: (inch) 7/8"
Construction: Polypropylene
Color: White
*Plastic thru-hull connectors are designed for installation above the water line only
|
7.25 |
|
|
316 SS T-Bolt Clamp - 3/4" Band - 1.78"-2.09" Range - 10-Pack
Very strong and secure clamp for critical installations. Trident Marine T-Bolt Clamps are built with safety in mind. With a 3/4" (19 mm) wide band, this clamp ensures a greater area of coverage for a positive and strong union.
Recommendations:
For our Silicone and PVC products
Can be used on any hose connection with peace of mind that they will last you a very long time
It is recommended that two clamps be used on each end of a wet exhaust installation.
Construction:
Band & Housing: 316 stainless steel 3/4” wide band
T-Bolt and Nut: 18-8 stainless steel with nylon insert
Specifications:
Hose Inner Diameter (inch): 1-3/8" - 1-1/2"
Hose Outer Diameter (inch): 1.78" - 2.09"
|
79.39 |
|