White Vertical Cup & Cap for Scandvik Part Number 1075 This is a white replacement cap and cup for the vertically mounted recessed showers. This part is a kit (one #10030 cap and one #10031 cup). Features: These showers are typically mounted on the side of a center console or any vertical surface You can distinguish the vertically mounted unit by the Scandvik logo on the cap Specifications: Mounting Hole: 2-1/4 in. *The "P" within the part number indicates retail packaging

White Container & Cap for Scandvik Part Numbers 10055,10275,10298, & 10826 This is a replacement cap and cup for horizontally mounted recessed showers. Horizontally mounted showers can be distinguished by the shower on the cap. This specific model is a kit (one #10252 cap and one #10253 cup). Note: Pull-out shower/sprayer handle uses cups #10253 (white) or #10264 (black) and a white cap #10252 or a black cap #10263 Mixer valves use the white cup #10335 and the same white cap, #10252 *The "P" within the part number indicates retail packaging

Replacement White Cup & Cap for Recessed Shower This recessed cap and cup design is made with Dupont™ Zytel® Nylon Resin for greater strength and UV exposure resistance. A rubber gasket under the cap will keep water out when the cap is closed.  Features: Requires a 2-3/4 in. mounting hole.    Single white cap and cup NOTE: If you currently have a Scandvik recessed shower with a rubber cap, this latest design version will NOT fit your hole size. You will need to enlarge your current 2 1/4-in. hole to a larger 2 3/4-in. *The "P" within the part number indicates retail packaging

Recessed T-Handle Mixing Valve - Stainless Steel with White Cup This recessed mixer and shutoff valve features a 316 stainless steel cap. Can be used as a mixer for recessed showers in both vertical and horizontal installations. Features: White composite cup with mixer This cap design for recessed showers and valves will add a touch of elegance to a boat The friction-lock hinge holds the cap open Mounting hardware is included Water Connection: Mixers: Flexible supply lines with 1/2 in. NPS-F fittings 3/8 in. BSP-M output connection to shower hose Shut-off Valves: 3/8 in. BSP threaded shaft with M 1/2 in. NPS adapter included Specifications: Material: 316 stainless steel Cap and composite cup Mounting Hole: 2-3/4 in. Shipping Weight: 5 lbs.

Recessed Shower with 6' White Hose - Push-Button This part is part of the fifth generation of Scandvik recessed showers. Also, this recessed shower has an easy-to-use push-button. Features: White handle, cup, and cap with a 6 ft. white hose Improved UV protection and a better water seal when the cap is closed Built-in grab ring for easy deployment Mounts vertically or horizontally Mounting hardware is included Specifications: Water connection: 3/8 in. BSP-F threaded fitting Material: ABS and chrome-plated brass (push-button) Mounting Hole: 2-3/4 in. Shipping Weight: 4 lbs. *The "P" within the part number indicates retail packaging

Recessed Shower with 6' White Hose - Euro Trigger Sprayer This part is part of the fifth generation of Scandvik recessed showers. Also, this recessed shower has an easy-to-use Euro trigger sprayer handle. Features: White handle, white cup & cap with 6’ white nylon hose Improved UV protection and a better water seal when the cap is closed Built-in grab ring for easy deployment Mounts vertically or horizontally Mounting hardware is included Specifications: Water connection: 3/8 in. BSP-F threaded fitting Material: ABS and chrome-plated brass (push-button) Mounting Hole: 2-3/4 in. Shipping Weight: 4 lbs. *The "P" within the part number indicates retail packaging

White & Stainless Steel Recessed Transom Shower Handle/Hose - Vertical/Horizontal Mount - 6' Hose This recessed shower cap with composite cup mounts vertically or horizontally. Ideal as a deck or transom shower. Features: Push-Button sprayer ABS handle with an attached lanyard for easy pull-out Mounting hardware is included White with 6 ft. black nylon hose Specifications: Water Connection: 3/8 in. BSP-F threaded fitting on the hose  Mounting Hole: 2-3/4 in. diameter Shipping Weight: 4 lbs.

Utility Light - Cool White - 10-30V This is a surface-mount, low-profile E-330 LED compact engine room light. The white plastic end cap features a notch on the wire side to allow side access for the connection wires. A low-profile fixture extends a mere 5/8" from the mounting surface. Features: 12/24 Volt (10-30 VDC) - 10 Watt 33 x 0.5-watt 2835 LEDs Cool white (5700-6300K) Polycarbonate lens with plastic housing IP67 Meets requirements and standards for SAE J1171 USCG, ABYC & NMMA Specifications: Lumens: 727 Beam Angle: 120° Surface Mount (wire can exit from the bottom or end of the fixture) *The "P" within the part number indicates retail packaging

K-Cup Holder 4-Capsule - Teak The Whitecap Teak K-Cup Holder looks good and helps organize any kitchen. This K-Cup holder is completely constructed of durable teak that resists warping, rotting, termites, and other insects. Teak's naturally high oil content makes it resistant to salt, sun, snow, and rain, making it a favorite for marine use. Features: Suitable for indoor or outdoor use No assembly required Finish: Oiled Lifetime warranty on teak

K-Cup Holder 6-Capsule - Teak The Whitecap Teak K-Cup Holder looks good and helps organize any kitchen. This K-Cup holder is completely constructed of durable teak that resists warping, rotting, termites, and other insects. Teak's naturally high oil content makes it resistant to salt, sun, snow, and rain, making it a favorite for marine use. Features: Suitable for indoor or outdoor use No assembly required Finish: Oiled Lifetime warranty on teak

K-Cup Holder 12-Capsule - Teak The Whitecap Teak K-Cup Holder looks good and helps organize any kitchen. This K-Cup holder is completely constructed of durable teak that resists warping, rotting, termites, and other insects. Teak's naturally high oil content makes it resistant to salt, sun, snow, and rain, making it a favorite for marine use. Features: Suitable for indoor or outdoor use No assembly required Finish: Oiled Lifetime warranty on teak

30° EPA Pull-Up Deck Fill Angled 1-1/2" (Water) Features: 1/4-turn pull-up cap with safety chain EPA approved for audible/visual open/close of cap Color-coded and imprinted with international standard symbols For use with carbon canister Pressure test cap available, PN 6062PC Chain Included Specifications: Type: Water Dimensions: Flange: 3" Hose: 1-1/2" Fastener: #10(3) 316 Stainless Steel

30° EPA Pull-Up Deck Fill Angled 1-1/2" (Waste) Features: 1/4-turn pull-up cap with safety chain EPA approved for audible/visual open/close of cap Color-coded and imprinted with international standard symbols For use with carbon canister Pressure test cap available, PN 6062PC Chain Included Specifications: Type: Waste Dimensions: Flange: 3" Hose: 1-1/2" Fastener: #10(3) 316 Stainless Steel

Suction Cup Mount Navigate with your zūmo® device in your vehicle with this suction cup mount. Take advantage of zūmo® 350LM's versatility. Move your zūmo from your motorcycle to your car dashboard or windshield with this automotive suction cup mount.1 1 Notice regarding windshield mounting legal restrictions: Before using the suction cup mount on your windshield, check the state and local laws and ordinances where you drive. Some state laws prohibit drivers from using suction mounts on their windshields while operating motor vehicles. Other state laws allow the suction mount to be located only in specific locations on the windshield. Many other states have enacted restrictions against placing "non-transparent material" on the windshield or placing objects on the windshield in locations that obstruct the driver's vision. Compatible Devices: zūmo® 350LM WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Cap for Round Plastic Rod Holders Features For use with P1000B, P1000DW, P1015DB and P1015DW For plastic rod/cup holders with round top