|
FINISH THOMPSON STTS-40 USDA SS PUMP 40"
Sealed, Medium Viscosity/Flow
TT Series pumps offer light to medium viscosity fluid handling. Drum pumps in this series are ideal for liquids containing small particulate or solvents.
Features include:
316 stainless steel or CPVC tube materials
Tubes interchangeable with motors
Up to 2000 cP with M6X air motor
Available Lengths:
40 in (102 cm)
Tube Diameter:
1-1/2 in (3.81 cm)
Discharge Size:
1 in (2.54 cm)
Discharge Types:
Hose barb or tri-clamp
Hose Size:
1 in (2.54 cm)
Electric Motor
Air Motor
Maximum Flow:
10 gpm (38 lpm)
16 gpm (61 lpm)
Maximum Head:
10 ft (3 m)
30 ft (9 m)
Maximum Specific Gravity:
1.8
1.8
Maximum Viscosity:
500 cP
2000 cP
Tube Material:
FDA-compliant 316 stainless steel
Shaft Material:
FDA-compliant 316 stainless steel
Spacer Material:
FDA-compliant FEP
Impeller/Compressor Material:
FDA-compliant PTFE with stainless steel pin
Maximum Temperature:
150º F (66º C)
Minimum Temperature:
-10º F (-23º C)
|
1485.90 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6
CE
80-100psi@15-32cfm
400
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. Drum pump motors are available as electric or air pneumatic motors. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES) without the static protection kit .
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Please allow about two weeks for delivery.
|
467.81 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6X
CE
80-100psi@15-32cfm
600
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. This drum pump motor is a air pneumatic motor. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES without the static protection kit.)
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Air motor performance will depend upon user's compressor and system setup.
Please allow about two weeks for delivery.
|
581.25 |
|
|
FINISH THOMPSON DB22-P
Finish Thompson DB22P Pump End Only FTI DB22 Magnetic Drive Centrifugal DB Series Sealless Pumps, 2" Suction, 2" Discharge, FKM O-Ring, Polypropylene, 221 GPM, 90 PSI Max Pressure, 201 Max Feet of Head.
Bushing: Carbon
Connection Type: NPT
Discharge NPT (Inches): 2"
Heads To (Feet): 201
Impeller Size (Inches): 7.25" (7 1/4")
Magnet: 8-pole
Material:Polypropylene (PPG)
Maximum Flow (GPM): 221
Maximum Operating Temperature: 180°F (82°C)
Maximum Pressure (PSI): 90 PSI
Motor Frame Size: 184TC
Pressure Rating BAR: 6.2 bar
Spec. Gravity: up to 1.8
Suction NPT (Inches): 2"
Valve/Seat/O-Ring: FKM
Applications
Chemical transfer
Anodizing
Rinse water & waste water
Pickling chemicals
Pulp and paper
|
3788.96 |
|
|
FINISH THOMPSON AC8SJS1V700B0121- 2"X1.5"x7" 316 SS VTN PMP HD
Applications
Chemical processing
Printed circuit boards
Pharmaceutical
Waste water treatment
Port Sizes
(Suction x Discharge) &
Connection Types:
2 in x 1.5 in NPT or BSP
2.5 in x 2 in NPT or BSP
2.5 in x 2 in ANSI 150# Flanges
2 in x 1.5 in ANSI 150# Flanges
2 in x 2 in ANSI 150# Flanges
2.5 in x 1.5 in ANSI 150# Flanges
3 in x 2 in ANSI 150# Flanges
3 in x 3 in ANSI 150# Flanges
2.5 in x 1.5 in Electropolished Tri-clamps
2.5 in x 2 in Electropolished Tri-clamps
3 in x 2 in Electropolished Tri-clamps
Maximum Specific Gravity:
up to 1.8
Maximum Working Pressure:
120 psi (8.3 bar)
@3450 RPM
@2900 RPM
Flow Range*:
20 to 321.2 gpm
4.54 to 58.3 m3/h
Maximum Head:
247 ft
53.2 m
Power Range**:
5.5 to 15 hp
1.8 to 9.1 kW
*See Performance tab for individual impeller diameter capability
**Smallest to largest impeller on 1.0 s.g.
Type:
Stainless Steel Mechanically Sealed
Configuration:
Horizontal
Construction Materials:
316 Stainless Steel
O-ring Materials:
FKM, EPDM, Buna, or PTFE Encapsulated Silicone
Seal Type:
Bellows Type 21
Seal Materials:
Carbon, Ceramic, FKM, EPDM, SiC, Buna, or Kalrez®
Maximum Temperature:
300º F (149º C)
Kalrez® is a registered trademark of DuPont Performance Elastomers
|
2721.36 |
|
|
FINISH THOMPSON DB6V-T PUMP END PVDF/TEFLON 56C
|
1085.40 |
|
|
FINISH THOMPSON DB7V-T PUMP END, PVDF/TEFLON 56C
Pulp & Paper
Chemical Processing
Heat Exchanger
Circuit Board Printing
Magnetic Drive Pump, 3/4 HP,
Voltage 208-230/460,
Full Load Amps 2.4-2.3/1.15, 1-1/2 In.
FNPT Inlet, 1-1/2 In.
MNPT Outlet,
Motor Type Induction, Motor Enclosure TEFC,
69 GPM of Water @ 3 Ft. of Head,
69 GPM of Water @ 6 Ft. of Head,
69 GPM of Water @ 9 Ft. of Head,
64 GPM of Water @ 15 Ft. of Head,
58 GPM of Water @ 18 Ft. of Head,
50 GPM of Water @ 24 Ft. of Head,
Length 17-19/64 In.,
Width 7-1/2 In.
|
1107.90 |
|
|
FINISH THOMPSON DB8V-T PUMP END, PVDF/TEFLON 56C
|
1133.10 |
|
|
FINISH THOMPSON DB9V-T PUMP END, PVDF/TEFLON 56C
|
1143.90 |
|
|
FINISH THOMPSON DEFP004 DRUM PUMP 48" POLY/316
|
331.50 |
|
|
FINISH THOMPSON DEPP001 DRUM PUMP 27" POLY/316
|
160.88 |
|
|
FINISH THOMPSON GP22PEB016018 2" POLY PUMP SEALED 184 JM
|
1931.40 |
|
|
FINISH THOMPSON GP22PEB01601806 2" POLY PUMP 184JM 5HP 230-
|
3450.86 |
|
|
FINISH THOMPSON BTS-40 40" HIGH VISC SS DRUM PUMP
Finish Thompson Drum/Barrel Pump - BTS Model
Outer Material:
316 stainless steel
Diameter:
2" (51 mm)
Seal:
graphite filled PTFE
Shaft Material:
316 stainless steel
Internals:
PTFE
Hose Size:
1 1/2" (40 mm)
Max Temperature:
200° F (93° C)
ELECTRIC
AIR
Max Flow:
10 gpm
2.3 m3/hr
10 gpm
2.3 m3/hr
Max Head:
200'
61 m
200'
61 m
Max Viscosity:
15,000 cP
15,000 cP
Length
Weight
Part No.
Box Dim.
40" (102 cm)
11 lbs (5 kg)
DBTS037
47" × 4" × 9"
(119 × 10 × 23 cm)
PART NO.
DESCRIPTION
DBTS037
BTS-40
|
1357.20 |
|
|
FINISH THOMPSON DB10P PUMP END POLY/CARB/VIT/56C
Applications
Water and wastewater
Electronics
Pharmaceuticals
Wet scrubber
Pulp and paper
Finish Thompson DB Series Pump
FTI's DB Series Magnetic Drive Pumps are the product of advanced engineering CFD design software and superior magnetic flux technology. Using powerful neodymium magnetic technology, the DB sealless mag drive pumps are an ideal replacement for mechanical sealed pumps in corrosive duty applications.
Finish Thompson Pumps: Centrifugal - DB10 Model
Motor @ 3450 RPM:
0.33 HP
Motor @ 2900 RPM:
0.34 kW
Max specific gravity:
1.8
Suction Port:
1.50 in
Discharge Port:
1.50 in
Impeller Diameter:
3 in (8.9 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
67.0 gpm
16.9 m3/hr
Max head
28.0 ft
9.8 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 63, 71, 80, 90, w/B14 or B5
Connection type:
NPT, BSP, Flange, Union
Magnet set:
6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW)
Max pressure:
80 psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
PART NO.
DESCRIPTION
DB10P
Pump End (PP)
DB10PW
Wet End (PP)
DB10V
Pump (PVDF)
DB10VW
Wet End (PVDF)
|
929.70 |
|