Flojet G575235 Air Pump Sp1 3/8Hbe 3/8Hbe The Flojet G575235 is a Flojet G57 Series Air Operated Diaphragm Pump, with Polypropylene housing, Santoprene Diaphragm, Santoprene Check Valve, EPDM O-Rings, Hastelloy Springs, and is driven by an internal air motor. This small air operated double diaphragm pump is designed to be the ultimate in performance and reliability. The robust design combines innovative features and relentless testing to offer a pump that has a long, trouble free service life.  This Air Operated duplex Diaphragm pump has leak resistant radial seals, eliminating the need for critical o-ring seals. It is is capable of passing 1/8 inch (3.2 mm) diameter solids easily with large clog free check valves. It has a unique shuttle valve that combines a long life ceramic slide valve with a unique spring design that eliminates stalling.   The Flojet G575235 Duplex Diaphragm Pump is designed for a wide range of applications and is constructed from a selection of materials suitable for handling a broad range of chemicals. Typical pump uses are Chemical Transfer and Dispensing, Solvent Applications, Parts Washers, Ink Transfer, and Car Wash Systems. When starting this pump, regulate the gas pressure to desired setting. For most installations 20 PSI 1.4 bar inlet will be adequate, although DO NOT go below 20 PSI. Pump will operate according to air supply.

Flojet I304010110 Pump 115V 3.5/45 Psv Sw  Flojet- Diaphragm Pump Duplex II 115V, 3/8”FNPT Ports, 3.5GPM, 45psi Switch, Polypropylene, Viton Valves, Santoprene Diaphragm, 6' Power Cord

Flojet 01740-003S Strainer 3/8" Barb X 3/8" Barb Flojet Strainer with 3/8” Hose Barb Inlet and 3/8” Hose Barb Outlet, In-Line Design, Fine 40 Mesh Stainless Steel Screen   Strainers for In-Line Applications. FDA Approved for Potable / Drinking Water.   Strainer Body made of Polypropylene with Clear Polysulfane Cap and Buna-N FDA O-Rings. Suitable for Fresh or Salt Water use. Easily Cleaned with See Through Thread-On Cap.   Course 20 Mesh Screens are typically used for Washdown, Bilge and Toilet Rinse Applications. Fine 40 Mesh Screens are typically used for Potable / Drinking Water Applications.   Maximum Flow Rates: With 3/4" Hose Barb Fittings: 7.0 GPM (27 LPM) With 1/2" Hose Barb Fittings: 4.0 GPM (15 LPM) With 3/8" Hose Barb Fittings: 2.1 GPM (8 LPM)   Maximum Water Temperature: 160F (70C) Maximum Pressure: 70 PSI (5 bar)   The Strainers that are Equiped with a "Direct Plug-In Quad Port" will fit into the Snap-In Quad Ports on Flojet Diaphragm Pumps and Jabsco Diaphragm Pumps sized under 6 GPM.

Flojet 04300-529A Mpu 115V S/V 3C Sw40 Flojet 04300529A Electric Quad Series Diaphragm Pump With 6 Ft. Cord - 3.5 GPM, 35 PSI, 115VAC Polypropylene Pump & Motor Assembly   The Flojet 04300529A pump is part of the Flojet 4300 Quad Series. This versatile pump cam be used for low-pressure car wash services, water treatment, filtering, and more. It is made with chemical resistant materials including a Polypropylene body, a Viton check valve, and a Santoprene diaphragm. The Flojet 04300529A pump includes 1/2" snap-in hose barb style ports and a 6' power cord. It has a 35 PSI maximum pressure rating and a flow rate of 3.5 GPM. Quiet, smooth, and safe operation! Specifications and Benefits: 3.5 GPM 35 PSI 115 volt AC 1.8A maximum amps Continuous duty induction motor 1/2" hose barb inlet 1/2" hose barb outlet Polypropylene housing Viton check valve Santoprene diaphragm 6' power cord Snap-in ports for easy installation 130° Fahrenheit maximum fluid temperature Can run dry without damage Excellent self-priming capability (up to 8 feet vertical) Powerful magnet motor with low current draw 4 piston design delivers high flow rates Handles water-like and viscous liquids up to 250 cP CE Certified

Flojet 02100-895 Pump 24V Santo 0Cam  Flojet- Diaphragm Pump Duplex 24V, 3/8"FNPT Ports, 1.4GPM, 50psi Max, Polypropylene, EPDM Valves, Santoprene Diaphragm, no Switch, no Bypass

Tuthill 000LEV-C-7 Pump 0.5Gpm 3/8 Ports Pump Body: Cast Iron  Relief Valve: Relief valve is factory set to 55 PSI with adjustment between 55-120 PSI Shaft Seal: Mechanical Seal Viton Port Size: Inlet Port is 3/8 inch NPT, Discharge Port is 3/8 inch NPT Product Specs : Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 0.5 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Flojet 20381-060 Ports 3/8"OD Straight Push Flojet Fitting 20381-060 Port x 3/8 inch O.D. Straight Push in Tube Fitting O-Ring Material of Viton (2) per package Used with Flojet and Hanna

Flojet 01720-375B Strainer 3/8 Brb 20 Mesh Strainers for In-Line Applications. FDA Approved for Potable Drinking Water. Strainer Body made of Polypropylene with Clear Polysulfane Cap and Buna-N FDA O-Rings. Suitable for Fresh or Salt Water use. Easily Cleaned with See Through Thread-On Cap. Course 20 Mesh Screens are typically used for Washdown, Bilge and Toilet Rinse Applications. Fine 40 Mesh Screens are typically used for Potable / Drinking Water Applications. Maximum Flow Rates: With 3/4" Hose Barb Fittings: 7.0 GPM (27 LPM) With 1/2" Hose Barb Fittings: 4.0 GPM (15 LPM) With 3/8" Hose Barb Fittings: 2.1 GPM (8 LPM)

Flojet G57520GA Air Pump 5Gpm 3/8" The Flojet G57520GA is a Flojet G57 Series Air Operated Diaphragm Pump, with Polypropylene housing, Santoprene Diaphragm, Santoprene Check Valve, EPDM O-Rings, Hastelloy Springs, and is driven by an internal air motor. This small air operated double diaphragm pump is designed to be the ultimate in performance and reliability.  The robust design combines innovative features and relentless testing to offer a pump that has a long, trouble free service life. This Air Operated duplex Diaphragm pump has leak resistant radial seals, eliminating the need for critical o-ring seals. It is is capable of passing 1/8 inch (3.2 mm) diameter solids easily with large clog free check valves. It has a unique shuttle valve that combines a long life ceramic slide valve with a unique spring design that eliminates stalling.    Applications The Flojet G57520GA Duplex Diaphragm Pump is designed for a wide range of applications and is constructed from a selection of materials suitable for handling a broad range of chemicals. Typical pump uses are Chemical Transfer and Dispensing, Solvent Applications, Parts Washers, Ink Transfer, and Car Wash Systems. When starting this pump, regulate the gas pressure to desired setting. For most installations 20 PSI 1.4 bar inlet will be adequate, although DO NOT go below 20 PSI. 

Flojet G57-3208 Pump Aod Viton 3/8" Ports Flojet Diaphragm Pump AOD Air Powered, 3/8" Hose Barb Snap-In Ports, 4.5GPM Max, Polypropylene, Viton Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Plastic Air Inlet Capable of Air or CO2 drive pressures up to 100PSI (6.9bar) Highest flow rate for any air pump of comparable size Robust Design with durable integral mounting Patented Shuttle Valve, eliminates stalling Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves Corrosion Resistant materials capable of handling a wide range of chemicals Sanitary design with insert molded diaphragm (Santroprene only) Leak Resistant radial seals, no critical o-ring seals Quiet Operation with large exhaust muffler Ease of Installation with all quick disconnect ports Stall-proof design with patented shuttle valve   Automotive Cleaning and Recycling;Chemical Transfer and dispensing;Bag-In-Box chemicals Parts Washers ;Car Wash Systems   Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.

Flojet G57-5215 Pump Air 5.5/100 Santo 1/2 Flojet Diaphragm Pump AOD Air Powered, 1/2” Hose Barb Snap-In Ports, 5.5GPM Max, Polypropylene, Santoprene Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Brass Air Inlet   Model No.: G57 Series Capable of Air or CO2 drive pressures up to 100PSI (6.9bar) Highest flow rate for any air pump of comparable size Robust Design with durable integral mounting Patented Shuttle Valve, eliminates stalling Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves Corrosion Resistant materials capable of handling a wide range of chemicals Sanitary design with insert molded diaphragm (Santroprene only) Leak Resistant radial seals, no critical o-ring seals Quiet Operation with large exhaust muffler Ease of Installation with all quick disconnect ports Stall-proof design with patented shuttle valve   Automotive Cleaning and Recycling; Chemical Transfer and dispensing; Bag-In-Box chemicalsParts Washers; Car Wash Systems   Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.

Flojet N5100020A Apu Viton 2.5Gpm  Flojet- Diaphragm Pump APU AOD Air Powered, 3/8” Hose Barb Snap-In Ports, 2.5GPM Max, Viton Check Valve and Diaphragm, 1/4” Hose Barb Air Ports

Flojet N5100050A Apu Geolast 2.5Gpm  Flojet- Diaphragm Pump APU AOD Air Powered, 3/8” Hose Barb Snap-In Ports, 2.5GPM Max, Geolast Check Valve and Diaphragm, 1/4” Hose Barb Air Ports

Flojet G57-3218 Pump Aod Viton 1/2" Ports Flojet Diaphragm Pump AOD Air Powered, 1/2" Hose Barb Snap-In Ports, 5.5GPM Max, Polypropylene, Viton Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Plastic Air Inlet   Model No.: G57 Series Capable of Air or CO2 drive pressures up to 100PSI (6.9bar) Highest flow rate for any air pump of comparable size Robust Design with durable integral mounting Patented Shuttle Valve, eliminates stalling Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves Corrosion Resistant materials capable of handling a wide range of chemicals Sanitary design with insert molded diaphragm (Santroprene only) Leak Resistant radial seals, no critical o-ring seals Quiet Operation with large exhaust muffler Ease of Installation with all quick disconnect ports Stall-proof design with patented shuttle valve   Automotive Cleaning and Recycling; Chemical Transfer and dispensing; Bag-In-Box chemicals Parts Washers; Car Wash Systems   Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.

Flojet 04524-500A Pump 115V S/E 4.5Gpm 45Psi Flojet- Diaphragm Pump Quad, Water Pressure System, VSD, 115V, Automatic Variable Speed for Constant 45PSI Pressure at Up To 5GPM, Santoprene Diaphragm, EPDM Valves, No Accumulator Tank Required, Includes Power Cord and 10/13mm (1/2") Hose Barb Snap-In Port Fittings Features: 4524 Series AC Quad Pump with VSD Module The AC Variable Speed Drive constant pressure pump system matches motor speed to system demand. As more liquid is needed, the motor responds to increase flow. Conversely, as the demand lessens, the motor slows to a "super quiet" speed, always retaining a constant system pressure. The result is exceptionally stable flow and reduced apm draw. The Flojet AC VSD sensorcontrolled pumps provide stable, constantpressure operation on any AC application. Operation from no flow to maximum flow is proportionally controlled, eliminating unwanted pump switch cycling and the need for an accumulator tank. Model No. 4524 Series AC Quad VSD • Maintains steady fluid pressure in response to variable flow demand • No pressure switch • Conserves energy, low amp draw • Quiet running under normal use • Automatically adjusts motor speed to maintain pressure • Improves overall system performance • Eliminates bulky accumulator tank for limited SPACErequirements