BURKS 10CS5M, Turbine Pump 32.5 gpm 115/230v Burks close coupled 32.5 gpm turbine pump having 1-1/4" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1 hp power rating.   Burks exclusive unique regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. Compact space saving size No coupling - eliminates misalignment problems Dependable carbon ceramic mechanical shaft seal for temperatures to 225 deg F (107 deg C) Bronze impeller with monel blades - the only moving part Bronze raceway with cast-in vortex pockets - will not vapor lock 303 stainless steel pump shaft Easy to service Every pump factory tested

BURKS 3CR6M, Turbine Pump 230VAC Burks 3CR6M Turbine Pump. Close Coupled 230 Volts 60 Hz, Single Phase, 3450/2850 RPM, 1/3 Horsepower. ODP Motor Enclosure.   UNSPSC Code: 40150000

BURKS 3CR6M-V-SP, Turbine Pump 230v with Plug and Ground Wire Turbine Pump and Motor unit. Close Coupled to a 1/3 Horsepower, 3450 RPM, 230 HZ , 60 Volt, 1 Phase, ODP Motor. Ports are 1/2 Inches NPT Inlet, 1/2 Inches NPT Outlet.   UNSPSC Code: 40150000

Flojet 04300-242 Pump 230V 4.7/30 Pse Sw  Flojet- Diaphragm Pump Quad 230V, 1/2” Hose Barb Snap-In Ports, Open Flow 3.7GPM, 30psi Switch, Polypropylene, EPDM Valves, Santoprene Diaphragm

Flojet 04300-242 Tfe Pump 230V 4.7/30 Pse Sw  Flojet- Diaphragm Pump Quad 230V, 1/2” Hose Barb Snap-In Ports, 4.7GPM, 30psi Switch, Polypropylene, EPDM Valves with Teflon O-Ring, Santoprene Diaphragm

BURKS A3CR6M, Turbine Pump 4 gpm 230v Application: Carpet Cleaning Machines, Small Steam Generators, Solar Heating Systems, Booster Pump, Injector Venturi Operation, Cleaning and Flushing   Frame/Raceway : Bronze Impeller : Bronze (Monel Blades) Shaft : #316 Stainless Steel Front Cover : Bronze Shaft Seal : Carbon-Ceramic / S. Steel / Buna-N   MAXIMUM OPERATING CONDITIONS TEMPERATURE (For Standard Buna-N Seal) : 225°F (107°C) INLET PRESSURE : 50 PSI (344kpa) CASING WORKING PRESSURE : 150 PSI (1034kpa) VISCOSITY : 200 SSU   FEATURES • Compact Size-Ideal for OEM Applications • All Bronze Construction with Monel Impeller Blades • Carbon/Ceramic Shaft Seal for Temperatures to 225°F (107°C) • #316 Stainless Steel Shaft • Close Coupled Design - No Couplings or Alignment Problems • Motors have ball/ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof. Rated for continuous duty operation at all ratings shown. • Capacitor Start Motors Have Built-In Automatic Overload Protection • Furnished with UL Recongnized Motor Lead • Field Adjustable Impeller for Extented Service Life   Motors have ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof. Compact size: only 10 1/2" long x 4" wide x 6 1/4" high.)   UNSPSC Code: 40150000

BURKS 3CR6M-V, Turbine Pump 1/3HP 1PH 230V Viton Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction w/ Viton seal & O-Ring. Close Coupled to a 1/3 Horsepower, 3450 RPM, 230 Volts, 1 Phase Motor. Ports are 1/2 Inches NPT Inlet, 1/2 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 20CS6M Close Coupled Turbine Pump BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.   BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.   Self-Priming Pump Compact and Space-saving size No coupling so this eliminates misalignment problems Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C). Bronze impeller with Monel blades, therefore the only moving part Bronze raceway with cast-in vortex pockets – will not vapor lock #303 Stainless Steel pump shaft Every pump is factory tested     Motor Information 4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.     CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.   High Temperature   For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. 

BURKS 24CT6M, Turbine Pump 115/230v 1"Ports Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 1/4 Horsepower, 1750 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 24CT7MJAB, Turbine Pump 8gpm 1" NPT Ports 115/230VAC Burks close coupled 8 gpm turbine pump having 1" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1/2 hp power rating.

BURKS 5CT6M, TURBINE PUMP 115/230V 1/2HP 1PH Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 5CT6M-FE, TURBINE PUMP 115/230V 1PH 1/2HP BF Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower , 3450 RPM, 115/230 HZ , 60 Volt, 1 Phase, ODP Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.

BURKS 5CT7M, TURBINE PUMP 1/2HP 1PH 115/230V Bronze Fitted Cast Iron Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   FEATURES Cast Iron/Bronze/ Stainless Steel construction Low Flow - High Pressure   FOUR POSITION CASING Discharge can be located in any of four positions. Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates the need to disturb piping should the pump ever require service - the casing stays in the line.   ENCLOSED BRONZE IMPELLER Of the latest hydraulic design for maximum efficiency, impeller is balanced for vibration-free operation and threaded onto stainless steel motor shaft.   ENCLOSED GLASS FILLED NORYL® IMPELLER Of the latest hydraulic design for maximum efficiency, impeller has molded in brass insert threaded onto stainless steel motor shaft. *Noryl® Impeller is not designed for use with hydrocarbons.   MECHANICAL SHAFT SEAL Standard self-adjusting shaft seal for temperatures to 225°F (107°C) and pressures to 150 psi (1034 kpa). Ceramic seat and carbon seal face for long trouble-free service. Special seals are available for higher temperatures and fluids other than water.   MOTORS Standard pump motors are of open drip proof (ODP) construction and are rated with jet pump service factors for continuous duty operation. Motors are 56 frame size with NEMA standard mounting flange, one piece threaded stainless steel shaft and ball/ball bearing construction.   FACTORY TESTED After careful assembly and inspection, EVERY pump is factory tested and meets Hydraulic Institute standards.   UNSPSC Code: 40150000

Burks 5CT7MAB, Turbine Pump 115/230v 1Ph 1/2Hp All BRONZE Construction. Close Coupled to a 1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 10CS6M, TURBINE PUMP 115/230v 1PH 1HP BF Close Coupled to a 1 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.