|
Goulds GT10 Self-Prime Centrifugal Pump 1Hp 115/230
|
832.50 |
|
|
BURKS 10GA5-1 1/4AB, Centrifugal Pump 1HP 115/230v
All BRONZE Construction.
Close Coupled to a 1 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet.
Impeller Diameter is 4.13 Inches.
|
2368.43 |
|
|
BURKS 15WA6, Centrifugal Pump Self Priming 115/230v
Bronze Fitted Cast Iron Construction w/ Plastic Impeller. Close Coupled to a 1-1/2 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet.
|
2122.20 |
|
|
BURKS 7G5-1 1/4, CENTRIFUGAL PUMP 1PH 3/4HP 115/230V
Bronze Fitted Cast Iron Construction.
Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4 Inches.
|
1432.80 |
|
|
BURKS 30WA6, Centrifugal Pump 115/230v 3HP
Burks 30WA6 Centrifugal Pump, Self Priming, 60 Hz, Single Phase, 3500 RPM, 3 Horsepower, ODP Motor Enclosure.
Close Coupled to a 3 Horsepower 115/230 Volts motor
Bronze Fitted Cast Iron Construction w/ Plastic Impeller.
Ports are 1-1/2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet.
Please contact us for a shipping quote at http://www.clrmarine.com/Contact_Us
|
2650.46 |
|
|
Shurflo 8090-902-248 Pump 230V 100psi
The 8000 series diaphragm pump is the most widely used Shurflo industrial pump.
Shurflo 8090-902-248, Diaphragm Pump with 230 Volt AC Motor and 100 PSI Automatic Demand Switch. Nylon Pump Body, EPDM Valves, Santoprene Diaphragm. Inlet Port is 3/8 Inch-18 NPT Female, Discharge Port is 3/8 Inch-18 NPT Female. 1.4 GPM open flow.
|
237.71 |
|
|
March Mag-Drive Centrifugal Pump Plastic 230V Hi Speed Beer Pump
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
Unit System 60Hz 50Hz Max Flow
6 GPM
18.9 LPM
Max Head
12.1 FT
2.5 M
Power
.04 HP
.029 KW
Electrical
230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F
Materials are FDA Food Compliant
With 6 Foot Cord and Plug
Components are UL Recognized
American Made
|
358.80 |
|
|
Berkeley S39518 CP High Head
Berkeley S39518 is a high head, series CP, centrifugal pump with a noryl impeller. The CP series pumps have a heavy-duty cast iron construction and feature a heavy-duty motor with easy service design and four-position discharge.
Features
3/4 HP
Motor Voltage: 115/230
Pipe Tapping Sizes: Suction 1-1/4 in, Discharge 1 in.
Drain port provided for easy winterizing
All models include replaceable wear ring and feature back pull-out design for easy serviceability
CP Series with Noryl impellers are abrasion-resistant for normal applications with working temperatures to 140°F
Applications
Water systems and sprinkling for homes, farms and industry
This item has a warranty of 12 months from date of original installation, or 18 months from date of manufacture.
|
1059.84 |
|
|
BERKELEY B82456-01, SSHM-2 SERIES PUMP
Berkeley B82456-01 SSHM-2 Series Stainless Steel Centrifugal Pump, 2 HP, 230 Volts, Single Phase, 1-1/2" Suction, 1-1/4" Discharge.
Contact us for shipping cost at www.clrmarine.com/Contact_Us
|
2081.52 |
|
|
Iwaki MD-100RLT, 1 inch MPT in/outlet 1986gph 120v
Iwaki MD-100RLT Water Pump
Mag Drive Centrifugal Pump and Motor Assembly, GFRPP Polypropylene Construction, close coupled to a 1/3 Horsepower, 115 Volts AC, 1 Phase, TEFC Electric Motor. 1 Inch NPT Threaded Port Connections.
Japanese pressure rated flow pump.
1 inch MPT inlet and outlet.
1/3 HP Motor output.
3300 RPM motor speed.
120 volts
3.4 amps.
Max flow 35.6 GPM.
1986 GPH at 6 feet of head.
Max head 39.0 ft.
Max system pressure 25.6 psi.
Twin bearing system handles thrust loads, extends service life
Hollow rotating / internal cooling circuit reduces bearing temperature.
Compact / Quiet energy for easy maintenance.
Few moving parts for easy maintenance
WMD pumps have American Made Motors
MD pumps have Japanese Made Motors
RLT pumps are for pressure applications
RZT pumps are for very high pressure applications
RLXT pumps are for circulation and wet or dry return
Iwaki America Inc. of Holliston, Massachusetts, is a joint venture which grew from a 15 year association between Walchem Corp. of Holliston, MA and Iwaki Co. Ltd. of Tokyo, Japan. Combining Walchems 30 years of chemical injection and control experience with Iwakis 50 years of pump design engineering, Iwaki America offers the best chemical handling equipment for use in Chemical Process, O.E.M., Industrial and Semiconductor applications.
|
748.00 |
|
|
Oberdorfer 405M-04-M26 Pump 3/4Hp 1725Rpm 115/230
NSN: 1304038-18-5
FEATURES
Pump Body:
Bronze
Ports:
1" NPT and 1 1/2" Hose
Flow:
24 GPM at 20 feet of head
Impeller:
Neoprene Standard, Buna Optional
Shaft Seal:
Mechanical
Shaft:
Stainless Steel
Motor / Drive:
Close coupled Rubber Impeller Pumps are mounted directly onto the motor without the use of a shaft coupling. This pump is designed to be coupled to a Nema C 56C faced motor. It uses an aluminum adapter plate to accommodate the pump. The gas engine mount has its own adapter. We can supply additional motors and assemble for you.
APPLICATIONS / CHARACTERISTICS
RUBBER IMPELLER PUMP BRONZE CLOSE COUPLED
Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counterbored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. Suction lifts of 15 ft. are possible when pump is fully primed. Portable. Compact. Easy Impeller Replacement. Vacuum Switch Shut-off Optional.
Oberdorfer Flexible Impeller Utility Pump, 1"NPT Ports, Neoprene Impeller, 3/4HP 115/230V ODP Motor
|
1623.96 |
|
|
March Mag-Drive Pump 115/230V Cast Iron Flanged Ports
Applications for the 830-CI Magnetic Drive Pump include hot water and hot oil systems.
March Pump's industrial 830-CI is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 15 gallons per minute at 11 feet, and its maximum head is 30.5 Feet (or around 13PSI). The standard wet end (the materials that come into contact with the solution) is composed of Cast Iron, Stainless Steel, Ceramic, Ryton/Teflon/Carbon, and Nitrile/Fibre. The inlet connection is a flange, and the outlet is a flange. The standard motor is a 1 Phase 115/230V 0.2 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Unit System 60Hz 50Hz Max Flow
15 GPM
52.9 LPM
Max Head
30.5 FT
6.5 M
Power
.2 HP
.149 KW
Electrical
115/230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
Flange
Outlet
Flange
Wet End
Cast Iron (Front Housing), Stainless Steel (Rear Housing, Shaft), Ceramic (Thrust Washer), Ryton/Teflon/Carbon (Impeller), Nitrile/Fibre (Gasket)
|
978.30 |
|
|
March Pump- Mag-Drive Centrifugal 115V Pump 1X3/4 Smooth Ports
• March AC-4C-MD and BC-4C-MD series pumps can deliver a maximum flow of 14 GPM (50 LPM), and are capable of serving applications with a maximum head of 21.5 ft. (4.7 m) (49 ft. [15.6 m] when driven by an air motor).
• Applications include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets and food heating cabinets.
• Standard construction is of polypropylene, with optional wetted materials that include Ryton or Kynar. Other materials include: Ceramic, Buna N rubber, and Viton for total chemical compatibility.
• Drive choices are a 1/12 HP (.062 kw), 3450 rpm air cooled or a 1/10 HP (.074 kw) 3450 rpm blast-cooled, 115-volt single phase, 50/60 Hz. motor. 230 volt optional.
March Pump Mag-Drive Centrifugal Pump 115V Air Cooled 14GPM 1" Hose Inlet, 3/4" Hose Outlet
|
506.86 |
|
|
BURKS 3CT5M, Turbine Pump 1/3HP 1PH 115/230 volt
Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/3 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
1918.80 |
|
|
Little Giant Submersible Pump 523112
Little Giant P-AAA Submersible 230 Volt Pump
Motor 230 Volt 50/60 Hz 1/160 HP Permanently Lubricated Oil Filled Motor, 120 GPH at 1 Foot Head, Shutoff Head 4.6 Feet, Inlet: Screened, Outlet: 1/4" MNPT or 1/2" Tubing with Elbow Fitting, Nylon Body, Fluid Temperature Up to 120F (49C), 12 Foot Power Cord.
523112 For commercial, industrial, and home use worldwide where liquid must be transferred or recirculated. Applications include aquariums, swimming pools, water displays, ice makers, air conditioners, boat bailing, fuel oil transfer, circulating water for welding and pipe threading machines, pumping mild chemicals such as soap solutions, acids, plating solutions and fertilizers.
|
164.58 |
|