|
AMT Pump HP02-99-09 Piston Drum Pump 3/4 Poly
Model HP02-99 Features:
Polypropylene Construction with Kynar Seals and Ryton® Piston Ring
Delivers 13 oz. per Stroke
Polypropylene Construction with Stainless Steel Components
• Kynar Seals and Ryton® Piston Ring
• Maximum Temperature 130° F
• 13 oz. per Stroke
• 3/4" NPT Discharge Port
• 3/4" x 40" Polypropylene
Suction Tube Assembly
• 2" Polypropylene Bung Adapter
Polypropylene Drum pump is designed for transfer and dispensing of liquids within a pH range of 4 to 11. Liquid types include many organic acids, alcohols and water soluble inorganic chemicals, which are compatible with pump component materials.
|
204.46 |
|
|
AMT 5750-99, Piston Drum Pump 1" NPT Discharge Port
PISTON DRUM PUMP
• All Polyethylene Construction
• Upper Temperature Rating: 158 degrees fahrenheit
|
74.59 |
|
|
Amt 2850-99 Cast Iron 1 1/4" Self Priming Pedestal Pump
AMT Self-Priming Centrifugal Pedestal pumps are designed for a wide range of industrial, agricultural and commercial applications. Dual volute design reduces radial load on bearings and motor. Heavy duty cast iron construction with Buna-N seals or stainless steel with Viton® seals. Pumps are fitted with a self-cleaning, semiopen impeller and are coupled to a heavy duty cast iron bearing housing with a CNC machined keyed shaft extension and sealed ball bearings. The pump has been designed for either direct connection or belt drive. The maximum recommended RPM is 4,000.
• Cast Iron & Stainless Steel Construction
• Buna-N Mechanical Seals on Cast Iron Models
• Viton® Mechanical Seals on Stainless Steel Models
• Optional Silicon Carbide Mechanical Seals Available
• 1-1/4˝, 1-1/2˝ or 2˝ NPT Suction and Discharge Port Sizes
• Dual Volute Design Reduces Radial Load on Motors
• Maximum Temperature
◆ Buna-N 180° F
◆ Viton® 200° F
• Self-Cleaning, Semi-Open Impeller
• Heavy Duty Cast Iron Pedestal Drive with Sealed Ball Bearings
|
41.92 |
|
|
AMT 4942-99, Rotary Drum Pump
ROTARY DRUM PUMP
Type: Rotary
Inlet: 1"
Outlet: 1"
Bung Adapter: Yes
Construction: Ryton
Seal: Teflon
|
208.85 |
|
|
AMT 3682-95 Straight Centrifugal Pedestal Pump
Mechanical Seal: Buna-N
Maximum Temperature: 180° F
3/4 in. NPT Suction Ports
1/2 in. NPT Discharge Ports
Maximum Working Pressure: 75 PSI
Self-cleaning Impeller on General Service Models
Maximum Flow 35 GPM
Maximum Head 148 Ft.
Epoxy Coated Pedestal Drive and Discharge Port Rotates in 90° Increments on High Head Models
All pumps have Cast Iron Casing with Stainless Steel Impeller
AMT Straight Centrifugal Pedestal pumps are designed for continuous-duty OEM, Industrial/Commercial and processing applications including circulation, chemical processing, liquid transfer, heating and cooling. The high head models are ideal for sprinkler systems and pressure boosting.
Pull-from-the-rear design permits easy servicing without disturbing any piping. Pedestals feature CNC machined shafts with sealed ball bearings. AMT Straight Centrifugal Pedestal pumps are reliable, cost effective and low maintenance. For use with nonflammable liquids compatible with pump component materials.
|
380.84 |
|
|
AMT Pump 5272-98 SS Rotary Drum Pump
Drum Pump, Stainless Steel, 1" NPT Suction x 3/4" NPT Discharge Port
Rotary drum pump for transfer of chemicals and liquids including many acids, acetones, trichloroethylene, solvents, photographic chemicals and ketones.
Hand-operated rotary lever action
304 stainless steel construction with carbon vanes and a Teflon (PTFE) seal for resistance to chemicals and corrosion
Flow rate of 12 oz. per stroke (5 gpm at 70 rpm)
1" female NPT inlet port and 3/4" female NPT outlet port
|
736.60 |
|
|
AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v
Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts
NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor
Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet
Cast Iron base and adapter
1 inch NPT cast iron flanges
304 series stainless steel components with Teflon wear rings
EPDM-Tungsten Carbide Seal that is easy to remove and replace
The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output. This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems. These pumps have NOT been investigated for use in drinking water systems.
|
1465.20 |
|
|
AMT Pump 5760-95 1Hp 2"Npt 115V CI-SS
Submersible Shredder Sewage Pump 5760-95, 130 GPM, 1.0 HP, Carbide Tipped
Cast Iron construction with stainless steel motor housing
1.0 HP, 14 Amps, 115 volts, continuous duty, single phase electric motor
Can handle solids up to 1 inch
Triplex seal system
2 inch output port with a discharge rate of 7800 gallons per hour
The AMT by Gorman-Rupp 5760-95 is an industrial grade shredder sewage pump that is designed to handle sludge and dirty water applications. Features an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging when pumping sludge type waste. Liquid content still must be above 85% to keep from damaging the pump and possibly void the warranty.
|
1244.98 |
|
|
AMT Pump 4822-95 Rotary Hand Pump
AMT Rotary Drum Pump
1" Suction & 3/4" Discharge
Buna-N Shaft Seal
Includes: Bung Adapter & Suction Tube Included
Material: Cast Iron
|
133.38 |
|
|
AMT Pump 3891-99 Threaded Shaft Pedestal
|
251.85 |
|
|
Amt 3693-013-09 Impeller For Am 3693-95/97
|
41.92 |
|
|
Amt 4891-010-09 Impeller For Am 4891-95/97
|
84.75 |
|
|
Amt 4901-010-09 Impeller For Am 4901-95/97
|
148.95 |
|
|
Amt 5351-95, Cast Iron Coolant Pump 230/460volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motor (TEFC)
Three Phase Motor
230/460 volts 0.8/0.4 amps
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
Delivers up to 56 GPM and 26 PSI
3/4" FNPTOutlet
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.
|
507.94 |
|
|
AMT 5390-95, Immersion Coolant Oil Pump 23gpm 115volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motors (TEFC)
115/230 volts, 3.0/1.5amps
Single or Three Phase Motors
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
1/2 inch FNPT Ports
Delivers up to 23 GPM and 26 PSI
Replacement For The Following Standard Machine Tool Industry Pumps
Fuji: VKP-063A
Old Fuji: VKN-061A
Mitsubishi: NQ100J
Toshiba: OPF-100M
Hitachi: CPD-100M
Yasukawa: VFPC-100
Graymills: IMV-25
Gusher: VBV-14
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
|
502.04 |
|