|
Amt 5764-95 Sub Shredder Pump 3" Npt
SUBMERSIBLE SHREDDER SEWAGE PUMP
Cast Iron with Stainless Steel Motor Housing
Carbide-Tipped Shredder Impellers
Spiral Shredder Mechanism Plate Surface Hardened for Enhanced Cutting Ability
Silicon Carbide Lower Seal
3" NPT Port Sizes
Max. Temperature 104° F
3 HP
230 Volt
AMT Submersible Shredder Sewage pumps feature an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging and reduce maintenance when cutting through stringy, fibrous and sludge type waste. Applications include sewage pumping stations, septic tanks, sewage treatment plants, dirty water drainage, flood and emergency. Also ideal for grinder type solids reduction application. Motors are rated continuous duty and single phase models have thermal overload protection.
AMT Submersible Shredder Sewage Pumps are reliable, cost effective and low maintenance.
|
1824.94 |
|
|
AMT Pump 5760-95 1Hp 2"Npt 115V CI-SS
Submersible Shredder Sewage Pump 5760-95, 130 GPM, 1.0 HP, Carbide Tipped
Cast Iron construction with stainless steel motor housing
1.0 HP, 14 Amps, 115 volts, continuous duty, single phase electric motor
Can handle solids up to 1 inch
Triplex seal system
2 inch output port with a discharge rate of 7800 gallons per hour
The AMT by Gorman-Rupp 5760-95 is an industrial grade shredder sewage pump that is designed to handle sludge and dirty water applications. Features an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging when pumping sludge type waste. Liquid content still must be above 85% to keep from damaging the pump and possibly void the warranty.
|
1244.98 |
|
|
AMT 3682-95 Straight Centrifugal Pedestal Pump
Mechanical Seal: Buna-N
Maximum Temperature: 180° F
3/4 in. NPT Suction Ports
1/2 in. NPT Discharge Ports
Maximum Working Pressure: 75 PSI
Self-cleaning Impeller on General Service Models
Maximum Flow 35 GPM
Maximum Head 148 Ft.
Epoxy Coated Pedestal Drive and Discharge Port Rotates in 90° Increments on High Head Models
All pumps have Cast Iron Casing with Stainless Steel Impeller
AMT Straight Centrifugal Pedestal pumps are designed for continuous-duty OEM, Industrial/Commercial and processing applications including circulation, chemical processing, liquid transfer, heating and cooling. The high head models are ideal for sprinkler systems and pressure boosting.
Pull-from-the-rear design permits easy servicing without disturbing any piping. Pedestals feature CNC machined shafts with sealed ball bearings. AMT Straight Centrifugal Pedestal pumps are reliable, cost effective and low maintenance. For use with nonflammable liquids compatible with pump component materials.
|
380.84 |
|
|
Amt 5351-95, Cast Iron Coolant Pump 230/460volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motor (TEFC)
Three Phase Motor
230/460 volts 0.8/0.4 amps
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
Delivers up to 56 GPM and 26 PSI
3/4" FNPTOutlet
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.
|
507.94 |
|
|
Amt 2850-99 Cast Iron 1 1/4" Self Priming Pedestal Pump
AMT Self-Priming Centrifugal Pedestal pumps are designed for a wide range of industrial, agricultural and commercial applications. Dual volute design reduces radial load on bearings and motor. Heavy duty cast iron construction with Buna-N seals or stainless steel with Viton® seals. Pumps are fitted with a self-cleaning, semiopen impeller and are coupled to a heavy duty cast iron bearing housing with a CNC machined keyed shaft extension and sealed ball bearings. The pump has been designed for either direct connection or belt drive. The maximum recommended RPM is 4,000.
• Cast Iron & Stainless Steel Construction
• Buna-N Mechanical Seals on Cast Iron Models
• Viton® Mechanical Seals on Stainless Steel Models
• Optional Silicon Carbide Mechanical Seals Available
• 1-1/4˝, 1-1/2˝ or 2˝ NPT Suction and Discharge Port Sizes
• Dual Volute Design Reduces Radial Load on Motors
• Maximum Temperature
◆ Buna-N 180° F
◆ Viton® 200° F
• Self-Cleaning, Semi-Open Impeller
• Heavy Duty Cast Iron Pedestal Drive with Sealed Ball Bearings
|
41.92 |
|
|
AMT 285P-95, Self-Priming Centrifugal Pump 3/4 HP, 3 PH, 230/460 V
Cast Iron Construction
Buna-N Mechanical Seal and O-Ring with optional Viton? or Silicon Carbide Mechanical Seal and O-ring
1" & 1-1/4" NPT Suction and Discharge Ports
Dual Volute Design Reduces Radial Load on Motor
Maximum Working Pressure 75 PSI
Maximum Temperature 180 F
Self-cleaning, Semi-open Impeller
|
595.69 |
|
|
AMT 5390-95, Immersion Coolant Oil Pump 23gpm 115volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motors (TEFC)
115/230 volts, 3.0/1.5amps
Single or Three Phase Motors
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
1/2 inch FNPT Ports
Delivers up to 23 GPM and 26 PSI
Replacement For The Following Standard Machine Tool Industry Pumps
Fuji: VKP-063A
Old Fuji: VKN-061A
Mitsubishi: NQ100J
Toshiba: OPF-100M
Hitachi: CPD-100M
Yasukawa: VFPC-100
Graymills: IMV-25
Gusher: VBV-14
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
|
502.04 |
|
|
AMT 5391-95, Immersion Coolant Oil Pump 23gpm 230/460volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT/OIL PUMPS
Cast Iron Construction
1/4 HP 230/460V 3 Phase Immersion Type
Shaft Seal Material: Sealless Design
Speed (RPM): 3450
Type: IMM
Voltage: 230/460
Fluid Port: 0.5"
HP:1/4
Impeller Material: Stainless Steel
GPM: 23
Replacement for Standard Machine Tool Industry Pumps
Fuji: VKP-063A
Old Fuji: VKN-061A
Mitsubishi: NQ100J
Toshiba: OPF-100M
Hitachi: CPD-100M
Yasukawa: VFPC-100
Graymills: IMV-25
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.
|
487.69 |
|
|
AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v
Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts
NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor
Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet
Cast Iron base and adapter
1 inch NPT cast iron flanges
304 series stainless steel components with Teflon wear rings
EPDM-Tungsten Carbide Seal that is easy to remove and replace
The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output. This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems. These pumps have NOT been investigated for use in drinking water systems.
|
1465.20 |
|
|
AMT Pump 4821-95 Rotary Hand Pump Cast Iron
Heavy-duty Cast Iron body with Buna-N seal
5 GPM @70 RPM (11 oz./stroke)
Carbon vanes
0.75" suction x 1" discharge ports
0.75-Inch NPT steel discharge spout assembly (included)
1-Inch NPT x 40-Inch steel suction tube assembly (included)
2-Inch Cast Iron Bung adapter
Maximum Temperature 160F
Self-Priming
Capable of handling compatible fluids with a maximum of 5,000 SSU viscosity at a minimum of 70 degrees F liquid temperature (roughly equivalent to SAE 40 motor oil)
Liquids must be free of debris and solids for proper operation
|
83.37 |
|
|
AMT 5381-95, Immersion Coolant Pump Cast Iron 10gpm
INTERCHANGEABLE IMMERSION & SUCTION COOLANT/OIL PUMPS
1/8 HP Totally Enclosed Motor (TEFC)
Three Phase Motor
230/460 volts, 0.3/0.19 amps
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
Delivers up to 10 GPM
3/8 inch outlet diameter
Able to pump liquid down to 2 inches
Replacement for to following Standard Machine Tool Industry Pumps
Fuji: VKP-053A
Old Fuji: VKN-051A
Mitsubishi: NQ-60J
Toshiba: OPF-60M
Hitachi: CPD-060M
Yasukawa: VFPC-061DIF
Graymills: IMV-08
Gusher: VBV-18
|
250.97 |
|
|
AMT Pump 368B-95 Strt Cent Pmp Iron 1/2Hp
Engine/Motor Type: Total Enclosed Fan Cooled
Horsepower: 0.5 HP
Phase: Single-Phase
Pump Voltage: 115 Volt (Single-Phase), 230 Volt (Single-Phase)
Frequency: 60 Hz
Rated Current: 9/5 Amps
Pump RPM: 3450
Thermal Overload Protect: Yes
Motor Frame: 56J
Pump Type: Straight Centrifugal Pump
Pump Style: Electric Centrifugal Pump
Inlet Diameter: 3/4"
Outlet Diameter: 1/2"
Discharge Port Rotation: 90 Degree Increments
Max Gallon Per Min (GPM) : 38.0
Max Total Head (Static): 57 Feet
Maximum Pressure (PSI): 25
Max Working Pressure: 75 PSI
Solids Handling: Yes
Max Solids Handling (Inches): 0.125"
Self Priming Pump: No
Pump Housing Drain: Yes
Housing Material: Cast Iron
Impeller Type: Self-Cleaning, Semi-Open
Impeller Material: Stainless Steel
Seal Material (Mechanical Or Other): Buna-N
Temperature RangeTo 180 F
Port Type: NPT
Altitude Affected: Yes
|
510.48 |
|
|
AMT Pump 2825-95 Pump Cast Iron Self Prime 3/4Hp 1Ph
Pump Body: Cast Iron
Shaft Seal: Buna-N Shaft Seal
Port Size: 1-1/2 inch x 1-1/2 inch NPT Ports.
Motor Specs : 3/4 Horsepower, 115/230 Volts, Single Phase, ODP (Open Drip Proof) NEMA 56J Frame Electric.
Product Specs :
Cast Iron Construction with Buna-N Seals
Handles 3/8 Inch Diameter Semi-solids
NEMA 56J Motors with Stainless Steel Shaft
Maximum Working Pressure 75 PSI
Self-primes to 20 Ft.
Self-cleaning, Clog Resistant Impeller
Steel Base and Handle Included
Dual Volute Design
|
695.25 |
|
|
AMT Pump 2P7XZR Hatz Diesel Fire Pump
2" Engine Driven Portable High Pressure pump is cast aluminum construction with cast iron volute and male NPT ports. Pump applications include fire protection and irrigation. These pumps are available with a wide choice of standard and heavy duty gasoline or diesel fueled engines. These pumps feature high efficiency closed cast aluminum impeller. All models come equipped with EPDM/EPR elastomers and seals. Most models include a heavy duty steel roll frame.
Features
Removable/Replaceable Cast Iron Suction & Discharge Flanges
Discharge Port Rotates in 90 Increments
One Tool Serviceability, Tool Included with Engine Driven Models (Not with Kits)
Includes Strainer and Rubber Foot Mounting
Maximum Temperature 180 F
Specifications
Type: High Pressure Pumps
Series: 2" Engine Driven Portable High Pressure Pumps
Driver: Hatz Diesel 1B30
Seal Type & Elastomer/Faces: EPDM/EPR/CAR/CER
Tank Size (Gal/Ltr): 1.32 / 5.0
Run Time (Hr.): 2.7
Mounting: Roll Cage
HP: 5 HP
SUCTION: 2" NPT
DISCHARGE: 2" NPT
L 31" X W 22.5" X H 23.6"
Warranty: 1 Year
Product images are a representation only
|
6150.23 |
|
|
AMT 3201-96, Laundry Tray Pump 1/4 HP 115V
GENERAL PURPOSE LAUNDRY TRAY PUMP
Cast Aluminum Construction
Buna-N Mechanical Seal and O-Ring
1-1/4" NPT Suction and Discharge Port
Self-cleaning, Semi-open Impeller
Continuous Duty Motor 1725 RPM, 1/4 HP 115VAC Single Phase Open Drip Proof (ODP) 48Z Frame
The AMT Laundry Tray pump is a single stage, multi-vane open impeller unit. It is designed as a laundry tray pump but can be used for most gravity fed general service pumping applications. The open impeller design makes it particularly adaptable to dirty as well as clean liquids and is inherently resistant to clogging.
The AMT Laundry Tray pump is readily available “Off-the-Shelf” for fast 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.
|
282.56 |
|