The Original Wishbone Outrigger Holder The Original Wishbone Style Outrigger Holder has been in production for over 45 years. Setting the standard for the industry, our "Junior" outrigger holder has often been imitated, but never equaled. Its ease of operation, adjustable fishing angle, ability to lay down for bridges and small footprint makes it the ideal holder for a multitude of boats. Durability was the watchword at its conception. You won't find plastic parts in this holder. Constructed of heavy duty brass forgings, heavy wall brass pipe and a stainless steel main tube, it epitomizes strength and reliability. The three point mounting system provides maximum strength and distributes the stress to the mounting surface over a wide area. This holder can be mounted vertically or angled toward the stern. Somewhere between twenty to thirty five degrees is normal. Model OH226S is for use with our deluxe 19ft. single spreader poles and non-spreader poles up to 22ft. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Ampco Pumps AC114MD14T-S Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps AC114MD18T-S Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps AC114MD56C-S Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps CB+114MB56C-S Peo 1 1/2 X 1 1/2 Kit

MX7000CR Adjustable Angle holders MX7000CR (1-1/2" ID) are our strongest and most versatile holders. The three point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18". Recomended poles for MX7000CR AO8716CR - 16 ft Center Rigger (Mk II) AO8718CR - 18 ft Center Rigger (Mk II) MX8712CR - 12 ft MX Step- Tube Style MX8715CR - 15 ft MX Step- Tube Style MX8718CR - 18 ft MX Step- Tube Style MX8716CX - 16 ft MX Step- Tube Style - Single Spreader MX8720CX - 20 ft MX Step- Tube Style - Double Spreader

MX8000CR Adjustable Angle holders MX8000CR (1-5/8" ID) are our strongest and most versatile holders. The three-point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18". Recommended poles for MX8000CR MX8719CR - 19 ft MX Step- Tube Style MX8716CX - 16 ft MX Step- Tube Style - Single Spreader MX8719CX - 19 ft MX Step- Tube Style - Single Spreader MX8720CX - 20 ft MX Step- Tube Style - Double Spreader MX8722CX - 22 ft MX Step- Tube Style - Single Spreader or Double Spreader

Hypro 1510-0002, Base Plate 9 1/2 X 18 9 1/2" X 18" with 10 gauge steel See picture (A) for reference

Roller Bucket Gunwale Tie-Down - 2" x 18' This is a 2" x 18' Roller Gunwale Tie-down. This economical style gunwale features a roller buckle and two zinc chromate S Hooks for simple cinching that holds extremely tight. 1,000 lb. capacity.

Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim

Spreader Kit for AP3519XS Poles Spreader Kit SP4919SL/XS Silver for AP3519XS & AP3522 Heavy Duty Poles. Includes all spreader hardware and instructions. Not shown in picture: 1-3/8" x 18" Reinforcing Tube - 2 Each.

Little Giant Submersible Pump 527176 Little Giant NK-2 with 18' cord Submersible Pump Motor 115 Volt 60 Hz 1/40 HP Permanently Lubricated Oil Filled Motor, 325 GPH at 1 Foot Head, Shutoff Head 12.3 Feet, Inlet: Screened, Outlet: 1/4" MNPT or 1/2" Tubing with Elbow Fitting and Garden Hose Adaptor, Nylon Body, Fluid Temperature Up to 120F (49C), 18 Foot Power Cord   527176 For commercial, industrial, and home use worldwide where liquid must be transferred or recirculated. Applications include aquariums, swimming pools, water displays, ice makers, air conditioners, boat bailing, fuel oil transfer, circulating water for welding and pipe threading machines, pumping mild chemicals such as soap solutions, acids, plating solutions and fertilizers

Ampco Pumps AC114MD56C-S/VITON Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps CB+114M14T-S-3.75 Peo 1 1/2 X 1 1/2 Kit

Ampco Pumps AC216MD14T-S Peo 2 X 1 1/2 Kit Ampco's AC Series pumps have standard stainless steel adapters and type D,DG & E seals available. The Ampco AC Series pumps are in conformance with 3A Sanitary Standards for centrifugal and positive rotary pumps for milk and milk products. # 02-10 This Ampco AC Series pumps also have a standard 32RA (150 grit) finish on all product surfaces.