Gunnel Mount Outrigger Holders OH2016S Size: 1.75" Dimensions: 3 1/2 x 6 Attractive, Strong, and Bullet Proof all describe our Gunnel Mount Outrigger Holders. One piece flange construction. Plate, Tube and Bar-Pin are all cast simultaneously for the ultimate in strength. Curved Tube has Solid End Plug with Deep Slots to assure long service and reliability. Tubes are made with Port and Starboard slot orientation to optimize fishing angle. Flange mounts flush with gunnel. When tube is removed, gunnel is unobstructed. Unit has three positions, straight up Running, angled out Trolling and straight back for Bridge Clearing. Originally designed by Lee's in the 50's and copied by nearly all our competition. However, no one rivals our durability, fit & finish. Chrome on Brass construction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Side Mount Outrigger Holders OH2018S Size: 1.75" Dimensions: 4 1/2 x 7 1/2 Side Mount Bracket utilizes same curved tube as Gunnel Mount. One piece Bracket construction. Tube, Feet and Bar-Pin are all cast simultaneously for the ultimate in strength. Unit provides same three positions as Flush Mount. Same rugged Chrome on Brass Cosntruction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Gunnel Mount Outrigger Holders Size: 2.0" Dimensions: 4 x 6 1/2 Attractive, Strong, and Bullet Proof all describe our Gunnel Mount Outrigger Holders. One piece flange construction. Plate, Tube and Bar-Pin are all cast simultaneously for the ultimate in strength. Curved Tube has Solid End Plug with Deep Slots to assure long service and reliability. Tubes are made with Port and Starboard slot orientation to optimize fishing angle. Flange mounts flush with gunnel. When tube is removed, gunnel is unobstructed. Unit has three positions, straight up Running, angled out Trolling and straight back for Bridge Clearing. Originally designed by Lee's in the 50's and copied by nearly all our competition. However, no one rivals our durability, fit & finish. Chrome on Brass construction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Side Mount Outrigger Holders OH2020S Size: 2.0" Dimensions: 4 3/4 x 7 1/2 Side Mount Bracket utilizes same curved tube as Gunnel Mount. One piece Bracket construction. Tube, Feet and Bar-Pin are all cast simultaneously for the ultimate in strength. Unit provides same three positions as Flush Mount. Same rugged Chrom on Brass Cosntruction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flush Mount 30° Nylon Rod Holder - White  Corrosion-free nylon rod holder. These 30° light-duty fishing rod holders are an economical way to add more rod storage. Molded in one piece from UV-resistant Nylon, these rod holders are tough and corrosion-free. 10" tube. Cap is 4" long x 3-1/2" wide. Installs into a 2-1/16" hole. Mount with 3/16" screws (not included).

SnapIt! Marine P003 Flush Mount Pontoon Quad Drink Holder This Quad Drink Holder is sized to fit can drinks with insulated sleeves and many mugs. The mug opening diameter is 3.625”. Interior Dimension are 3.895x8.12”. Overall Height 3.86”. Overall Width 18.4”. Cutouts on top ring can be useful for hanging sunglasses, etc. Flush mount unit not suited for use in combination with P0011 tables. Mounts permanently to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included. Color: White

Flush Mount 30° Nylon Rod Holder - Black  Corrosion-free nylon rod holder. These 30° light-duty fishing rod holders are an economical way to add more rod storage. Molded in one piece from UV-resistant Nylon, these rod holders are tough and corrosion-free. 10" tube. Cap is 4" long x 3-1/2" wide. Installs into a 2-1/16" hole. Mount with 3/16" screws (not included).

MB-75 Flush Mount Kit For flush-mounting to a flat surface, such as a control panel. Compatible Devices: M424 M502 M504 M506 M602 M604 M605 M802 MA500TR

1-1/4" Flush Mount Flag Pole Socket Made from beautiful long lasting T316 polished stainless steel Insets nearly flush to the deck 60° angle

Ampco Pumps CB+114M14T-S-3.75 Peo 1 1/2 X 1 1/2 Kit

Swivel Base Flush Mount Rod Holder Part #: RH-5365SS Medium 30 Stainless Steel Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Flush Mount Rod Holder Part #: RH-5367SS Medium 0 Degree Stainless Steel Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Flush Mount Rod Holder Medium, 15 Degree, Stainless Steel Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip's roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

Extra Strong 20' Telescoping Carbon Fiber Outrigger Poles for Sidewinder Mount Advanced Carbon Composite Telescoping outriggers.  Lee's carbon fiber poles are by far stronger and lighter than any other aluminum pole on the market today.  Made "Extra Strong" by utilizing the lower four sections of a five section outrigger pole for an increased outer diameter and stronger pole. The perfect solution for trolling a variety of baits.  Features: Light Weight – Makes deployment, retrieval, raising, and lowering a breeze Strength – Spreaders become unnecessary A glossy clear coat finish is standard Technical Specifications: Length - 20' Number of Sections - Four (4) Mounting Base - Lee's Sidewinder 1-5/8" Rigging – Double rigging  Line  Strength – 400 lb. black monofilament Line Length -  *Sold as a Pair

4" Marine Flush Mount Spreader Light - Black Housing - Pro Series 3.0 With the increasing size of boats and the major popularity of Black Oak's 4" Marine Scene Spreader Lights, Black Oak's 4 Inch Flush Mount Marine Spreaders were born. Perfect for larger center consoles, sportfish yachts, and many other applications. This light gives off a whopping 3,120 raw lumens and a very widespread 120-degree light pattern.  Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market. Features: Spreader light 360° Ceramic Protection against UV, Salt Water & Corrosion 2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar Heavy-duty Dynamax housing for a 4x stronger frame Activities & Uses:  Spreader Light Aft deck fishing lights Foredeck lights Accent lighting Game fishing lights Boat wake lights Technical Specifications: Total Wattage: 40W Amp. Draw: 2.8 LED Quantity: 4 Weight: 0.35 lbs. Raw Lumens: 3,120 Warranty: Lifetime IP Rating: IP69K     Dimensions (Length x Height x Depth): 6-3/8" x 3-3/16" x 2-1/4”  Mounting Holes: 5-5/8” apart horizontally In the Box: 4” marine black flush mount spreader light Wiring pigtail  Stainless steel mounting kit *Sold as an Individual