Here is a list of some of the new items we have added ofer the last few days at CLR Marine.   Part Number              Product Title   10992    LILLY 406 SHIM/LONG TAPER 13762    INTERPHASE T1-1200-032 BT 200K HOR/VERT SCAN F/ TWIN PC/VIEW 16561    STANDARD HX471SS SILVER VHF HH AM002N005 17598    C-MAP AF-M204 SD CARD FORMAT SOUTHERN AFRICA 19030    BLUE SEA 7114 CIRCUIT BREAKER 80A 20216    BLUE SEA 2207 BLACK TERMINAL FEED-THROUGH 25433    MINN KOTA MK-330 3 BANK X 10 AMPS 27937    MUSTANG LIL' LEGENDS INFANT'S FLOATER VEST UP TO 30 lbs. 28704    SIMRAD TM NYLON D/S/T 600W TRI-DUCER 50/200 FOR NX40,45 31398    MINN KOTA PONTOON 55/HAND 12V 55LB 52" 33308    PROMARINER PRONAUTIC REMOTE DISPLAY HELM CONTROL / REMOTE 34940    FULTON 3200# CABLE WINCH 2-SPD W/ BRAKE HP SERIES 35446    NAVPOD PP4301 POWERPOD PRECUT FOR RAYMARINE ST60 39439    AQUATIC 6.5" WATERPROOF STEREO SPEAKER BLACK GRILL-PAIR 39892    OTTERBOX DEFENDER SERIES CASE HTC DESIRE 41017    OTTERBOX COMMUTER SERIES NOKIA E7 42050    MIDLAND NT3 5 WATT HANDHELD VHF RADIO W/ BELT CLIP 42531    JABSCO PAR-MAX WASHDOWN PUMP KIT 4.0GPM 60PSI 12VDC 42532    ONYX 7501 FLOTATION JACKET LARGE NAVY BLUE 42533    ONYX 7501 FLOTATION JACKET LARGE RED/GREY 42534    ONYX 7501 FLOTATION JACKET X-LARGE NAVY BLUE 42535    ONYX 7501 FLOTATION JACKET X-LARGE RED/GREY 42576    TIMEX IRONMAN 10 LAP MID SIZE WATCH BRIGHT GREEN 42577    TIMEX IRONMAN 30 LAP OVERSIZE WATCH BLUE/BLACK/SILVER 42584    TIMEX IRON KIDS DIGITAL WATCH BLUE/SILVER   42462    HUMMINBIRD FISHFINDER 570 42505    GARMIN NUVI 3450 42508    GARMIN GTM 60 DIGITAL 3D TRAFFIC RX 2400 3400 SERIES 42509    GARMIN NUVI 2455LT 42511    GARMIN NUVI 2475LT 42513    GARMIN NUVI 2555LT 42521    JABSCO AUTOMATIC WATER SYSTEM PUMP 4.0GPM 50PSI 12VDC 42522    JABSCO AUTOMATIC WATER SYSTEM PUMP 4.0GPM 50PSI 24VDC 42523    JABSCO AUTOMATIC WATER SYSTEM PUMP 4.0GPM 25PSI 12VDC 42524    JABSCO AUTOMATIC WATER SYSTEM PUMP 4.0GPM 25PSI 24VDC 42525    JABSCO AUTOMATIC WATER SYSTEM PUMP 5.0GPM 50PSI 12VDC 42526    JABSCO AUTOMATIC WATER SYSTEM PUMP 5.0GPM 50PSI 24VDC 42527    JABSCO AUTOMATIC WATER SYSTEM PUMP 5.0GPM 25PSI 12VDC 42528    JABSCO AUTOMATIC WATER SYSTEM PUMP 5.0GPM 25PSI 24VDC 42529    JABSCO AUTOMATIC WASHDOWN PUMP 5.0GPM 70PSI 12VDC 42551    TIMEX HEALTH TOUCH HRM WATCH SILVER/BLACK/RED 42552    TIMEX HEALTH TOUCH HRM WATCH BLACK/SILVER 42553    TIMEX HEALTH TRACKER WATCH BLUE/GRAY FLOWER 42554    TIMEX HEALTH TRACKER WATCH BLACK/GRAY FLOWER 42559    TIMEX IM ALLDAY 50 LAP PLUM SILICONE MS WATCH   37676    NAVIONICS PLATINUM SOUTH AMERICA EAST ON SD/MICRO SD 37679    NAVIONICS PLATINUM SOUTH AMERICA EAST ON CF CF/909P-2 42306    KESTREL RH CALIBRATION KIT RELATIVE HUMIDITY 42588    POWERHOUSE ICE EATER 1 HP 115V WITH 100FT CORD 42589    POWERHOUSE ICE EATER 1 HP 230V WITH 100 FT CORD 42590    POWERHOUSE TIMER 115V    

March LC-2CP-MD Mag Drive Pump 230V The most common application for the LC-2CP-MD Magnetic Drive Pump is for marine air conditioning and fountains. This pump will handle up to a 6,000 BTU Air Conditioner. March Pump's industrial LC-2CP-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (or around 5.5PSI).  The LC-2CP-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Buna N, and the Cord are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread and 0.75 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.028 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 25PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-2CP-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 5 GPM 18.5 LPM Max Head 13 FT 2.7 M Power .028 HP .021 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Stainless Steel (Shaft, Cooling Tube), Ceramic (Thrust Washer), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Buna N, Cord

Applications for the AC-2CP-MD Mag Drive include etching equipment, photographic processing equipment, ice makers, ice flakers, plate processors, and marine air conditioning.    March Pump's industrial AC-2CP-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 5 gallons per minute at 2 feet, and its maximum head is 13 Feet (or around 5.5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ceramic, and Ceramic Magnet. The inlet connection is 0.375 female pipe thread and 0.75 male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.025 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-2CP-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 5 GPM 18.5 LPM Max Head 13 FT 2.7 M Power .025 HP .018 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 3/8"FPT & 3/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washer), Ceramic Magnet

March LC-5C-MD Magnetic Drive Pump 230V The most common application for the LC-5C-MD Magnetic Drive Pump is for marine air conditioning and fountains. This pump will handle up to a 48,000 BTU Air Conditioner March Pump's industrial LC-5C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (or around 11PSI).  The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Stainless Steel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-5C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 14.5 GPM 54.8 LPM Max Head 27 FT 6 M Power .125 HP .097 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Shaft, Thrust Washers), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cord

March LC-3CP-MD Magnetic Drive Pump 230V The most common application for the LC-3CP-MD Magnetic Drive Pump is for marine air conditioning and fountains. This unit will handle up to a 24,000 BTU Air Conditioner March Pump's industrial LC-3CP-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (or around 8PSI).  The LC-3CP-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Cupric Nickel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Stainless Steel, Polysulfone, and the Cord are also in contact with the solution. The inlet connection is .075 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 25PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-3CP-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 8.5 GPM 31 LPM Max Head 19 FT 4.3 M Power .05 HP .037 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 3/4"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Cupric Nickel (Cooling Tube), Buna N (O-Ring, Cooling Tube Seal), Ceramic (Shaft, Thrust Washer), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Stainless Steel, Polysulfone, Cord

March TE-5.5C-MD Mag-Drive Centrifugal Pump single phase with 115/230V Motor   Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   The TE-5.5C-MD pumps Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Nitric Acid, Phosphoric Acid, Potassium Chloride, Potassium Hydroxide, Sodium Hydroxide (Caustic Soda), Sodium Chloride, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.   Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V                3PH 230/460V 50/60HZ   Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)  

March 0150-0250-0100 Marine Pump LC-5M-MD March Pump’s industrial LC-5M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI). The LC-5M-MD pump may be used submerged or not submerged. It is capable of 45,000 BTU a hour.   Max Flow: 54.9 LPM Max Head: 8.2 M Power: 0.093 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.125HP/0.0093kW, 0.9AMPS, 3450 RPM 50Hz: 1Ph 0.125HP/0.0093kW, 0.5AMPS, 2850 RPM   Inlet: 1"FPT Outlet: 1/2"MPT   Submersible: Yes   Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Carbon (Impeller Bushing), Ceramic (Thrust Washers), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Noryl, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Liquid Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP67   This pump is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI).  It is capable of 45,000 BTU a hour.  The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene,  Noryl, Buna N, Stainless Steel, Carbon, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius.     The pump is Ignition Protected per SAE J1171 and ISO 8846.  The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.  

March 1A-MD 3/8 Mag Drive Pump March Pump's industrial 1A-MD-3/8 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1A-MD-3/8 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 3/8 inch smooth, and the outlet is 3/8 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-3/8 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Perfect for Applications Including Applications for the 1A-MD-3/8 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   Great for Chemicals Including The 1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The 1A-MD-3/8 may have been modified to handle these chemicals.    Type: Centrifugal Mag Drive Inlet: 3/8"OD Outlet: 3/8"OD Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft) Uses: Submersible or Open Air When submerged, the following is also in contact with the solution, Epoxy, Noryl, SJT Cord    

March 0130-0178-0100 Marine Pump LC-3M-MD March Pump’s industrial LC-3M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (8PSI). The LC-3M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 24,000 BTU a hour.   System: 230v 50/60Hz Max Flow: 31 LPM Max Head: 4.3 M Power: 0.037 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.05HP/0.037kW, 1 AMPS, 3450 RPM 50Hz: 1Ph 0.05HP/0.037kW, 1 AMPS, 2850 RPM   Inlet: 3/4"FPT Outlet: 1/2"MPT   Submersible: Yes   Wet End: Polypropylene (Front and Rear Housing, Impeller), Cupric Nickel (Cooling Tube), Buna N (O-Ring, Cooling Tube Seal), Carbon (Impeller Bushing) Ceramic (Shaft, Thrust Washer), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Stainless Steel, Polysulfone, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Liquid Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP 67 UL Listed Motor: Note: Product image may be different than actual product received.

March 0125-0142-0100 Marine Pump LC-2M-MD March Pump’s industrial LC-2M-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (5.5PSI). The LC-2M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846.  It is capable of 12,000 BTU a hour. Max Flow: 18.5 LPM Max Head: 2.7 M Power: 0.014 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.025HP/0.019kW, 0.53 AMPS, 3450RPM 50Hz: 1Ph 0.18HP/0.014kW, 0.72 AMPS, 2850RPM   Inlet: 3/8"FPT & 3/4"MPT Outlet: 1/4"MPT   Submersible: Yes   Wet End: Polypropylene (Front Housing, Impeller), Nylon (Rear Housing) Viton (O-Ring), Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Thrust Washer), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Buna N, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Internal Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP67

Applications for the TE-5.5K-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   The TE-5.5K-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Hydrofluoric Acid, Hydrogen Peroxide, Nitric Acid, Phosphoric Acid, Potassium Chloride, Sodium Chloride, Sodium Hypochlorite, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals..  The TE-5.5K-MD may have been modified to handle these chemicals.     March Pump's industrial TE-5.5K-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), Viton, Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-5.5K-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 30 GPM 102 LPM Max Head 41 FT 9 M Power .33 HP .248 KW Electrical 1PH 115/230V      3PH 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1"FPT Outlet 3/4"MPT Wet End Carbon Filled Kynar (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)

March LC-2CP-MD Pump W/ 115V Motor

March 809 815 Series Mag-Drive Centrifugal Pumps The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports  

March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet