|
Flotec FP5162 Thermoplastic Sprinkler Pump 1 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 55 GPM
FLOW at 10' LIFT and 30 PSI: 28 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 42 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
593.25 |
|
|
Flotec FP5532 Cast Iron Centrifugal Pump 1 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Maximum pumping capacities to 68 GPM
Ready-to-install 230 volt motor (dual voltage)
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1
MAXIMUM CAPACITY: 47 GPM
MAXIMUM LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 49 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
LIQUID TEMP RANGE: 140 °F (60 °C)
|
531.75 |
|
|
Flotec FP5182 Thermoplastic Sprinkler Pump 2 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 2
MAXIMUM CAPACITY: 69 GPM
FLOW AT 10' LIFT and 30 PSI: 45 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 50 psi
SUCTION PIPE SIZE: 2" NPT
DISCHARGE PIPE SIZE: 2" NPT
AMP DRAW: 12 amps on 230v / 24 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 30 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
732.96 |
|
|
Flotec FP5172 Thermoplastic Sprinkler Pump 1.5 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1-1/2
MAXIMUM CAPACITY: 67 GPM
FLOW at 10' LIFT and 30 PSI: 45 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 47 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 9.6 amps on 230v / 19.2 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 25 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
621.00 |
|
|
Flotec FP5512 Cast Iron Centrifugal Pump 1/2 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install 230 volt motor (dual voltage)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 22 GPM
MAX LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 36 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 4.7 amps on 230v / 9.4 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
RECOMMENDED BREAKER: 15 amp on 230v / 15 amp on 115v
|
440.70 |
|
|
Flotec FPSE3601A Cast Iron Sewage Pump 1/2 HP
Rugged, sewage and effluent pumps are capable of handling solids up to 2". Available in cast iron design for a variety of wastewater applications.
Heavy-duty, rugged cast iron automatic submersible sewage pump
Capable of handling 2" solids - ideal for basement installations, pumping below grade toilets, laundry facilities, underground parking, grain storage and construction sites
Includes by-pass float switch for automatic or manual operation
BODY CONSTRUCTION: CAST IRON
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9000 GPH
FLOW AT 10' LIFT: 5400 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2" NPT
MINIMUM PIPE SIZE: 2" for sewage applications / 1-1/2" for effluent applications
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 10'
AMP DRAW: 13 amps
VOLTAGE: 115v. 60 Hz
RECOMMENDED BREAKER: 20 amp
|
699.00 |
|
|
Flotec FP4105 Cast Iron Jet Pump 1/2 HP
New cast iron shallow well jet pump is ideal for wells with pumping levels of 25' or less. Self-priming after the pump housing is initially filled with water.
KEY FEATURES
Reliable performance at 25' depth to water or less
Maximum pressures of 63 PSI and maximum pumping capacities to 5.1 GPM
Pump housing is constructed of heavy-duty cast iron and is ready to install
115 volt 1/2 HP
Fan cooled, completely enclosed motor
1" Suction Port and 1" Discharge Port
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 5.6 GPM
FLOW at 10' LIFT and 40 PSI: 4.5 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 63 PSI
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.2 amps
VOLTAGE: 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
381.42 |
|
|
Flotec FP4432 Vertical Deep Well Jet Pump 1 HP
Vertical deep well jet pump can be used in 4" diameter or larger wells up to 260', or in 2" diameter wells up to 180'.
KEY FEATURES
Superior performance at depths to water of 50' or more
Rugged, heavy-duty cast iron pump housing
Ready-to-install 230 volt motor - see manual for 115 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1
MAXIMUM CAPACITY: 12 GPM
FLOW AT 50' LIFT and 40 PSI: 11 GPM
MAX LIFT: 260' for 4" or larger well / 180' for 2" well
PRESSURE SWITCH SETTING: 40/60
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.6 amps on 230v / 19.2 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
1017.36 |
|
|
Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor - see manual for 115 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 20.7 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 18.3 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 90' for deep setup
MAXIMUM PRESSURE: 52 psi for shallow / 56 psi for deep
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW: 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
698.25 |
|
|
OBERDORFER CB9000L CAST IRON GEAR PUMP 1"
FEATURES:
• Flows to 24.8 GPM
• Max. RPM: 1725
• Max. PSI: 100
• Suction lift to 19.5 ft.*
• Maximum viscosity to 100,000 SSU at reduced speed
(max. input torque of 160 in.-lbs.)
• Housing gasket: Vellomoid
• Construction: Cast Iron housing, Steel gears, Steel shafts
• Shaft Seals: Synthetic Braided compression packing with Teflon dispersion
• Shaft Bearing Journals: Grease lubricated Cast Iron
• Temperature range: -20 to 210° F
• Maximum working pressure: 130 PSI
• Pumps can operate bidirectionally (reversible)
This Oberdorfer CB9000L is the drop in replacement for models C4K and C4V. It can also be considered as replacements for models 4KHK4 and 4KHJ7.
This self-priming, positive displacement, external rotary gear pedestal pump is ideal for oil based fluids in a wide
range of light-duty commercial, industrial, marine, and agricultural applications.
It is for use with particulate free and non-abrasive high lubricating oil-based fluids compatible with iron and steel.
Not to be used with water-based fluids. Line mounted pressure relief valves are recommended to protect downstream
equipment.
The pump should be mounted on a rigid base and properly aligned with the motor. Direct drive via flexible shaft coupling is the preferred method. When a belt drive is needed, additional support is necessary to absorb the added pulley load.
|
522.19 |
|
|
Myers Pumps ME40P-1 Effluent Pump 4/10Hp 115V
Myers ME40P-1 Cast Iron Effluent Pump Specifications
VOLTAGE: 1ø, 115V, 60 Hz
HORSEPOWER: 0.4 HP
AMP DRAW (full load): 12.0
MOTOR TYPE: Permanent Split Capacitor (PSC)
RPM: 1650
MAXIMUM HEAD: 32'
MAXIMUM CAPACITY: 80 GPM
SWITCH TYPE: Tethered Automatic
MINIMUM SUMP DIAMETER: Simplex 24" Duplex 36"
DISCHARGE PIPE SIZE: 1-1/2" FNPT
MAXIMUM SOLIDS HANDLING SIZE: 3/4" Spherical Solids
IMPELLER TYPE: Cast Iron, Two-Vane Enclosed
CORD LENGTH: 10'
CORD SIZE: 16-3; Type: SJTW
BODY CONSTRUCTION: Cast Iron
MAXIMUM LIQUID TEMPERATURE: 140°F (60°C)
|
673.56 |
|
|
Flotec FPSE2800A Thermoplastic Effluent Pump
The FPSE2800A provides the answer to many effluent/dewatering situations where 3/4" solids handling is all that is needed.
Automatic submersible effluent/dewatering pump
Capable of handling 3/4" solids - ideal for basement installations, laundry facilities, underground parking, grain storage and construction sites
Thermoplastic construction
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/3
MAXIMUM CAPACITY: 3600 GPH
FLOW AT 10' LIFT: 2700 GPH
SWITCH TYPE: Tethered
SWITCH ON LEVEL: 11-1/2"
SWITCH OFF LEVEL: 4-1/2"
DISCHARGE PIPE SIZE: 2"
MINIMUM PIPE SIZE: 1-1/2"
MAXIMUM SOLID HANDLING SIZE: 3/4"
CORD LENGTH: 15'
AMP DRAW: 7 amps
VOLTAGE: 115v, 60 Hz
|
436.80 |
|
|
BURKS 320GA5-1 1/4, Bronze Fitted Cast Iron Centrifugal Pump 230/460v
Bronze Fitted Cast Iron Construction. Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.88 Inches.
Burks end suction, three phase, close-coupled, bronze fitted, centrifugal pump with mechanical seal. They are ideal for booster service, recirculation, general water supply, and washer lines.
Construction: Casing and bracket are close grain cast iron. Enclosed 4-7/8" bronze impeller, 302 stainless steel motor shaft, single mechanical seal, carbon faces, buna elastomers, 304 stainless steel metal parts.
Connections: 1-1/2" X 1-1/4" female NPT suction and discharge Motor: 2 HP, 3450 RPM, Open drip proof, three phase, 208/230/460 volts, 60 Hz, ball bearings front and back, built-in overload protection.
Clockwise rotation, when facing back of motor. Maximum working pressure: 200 PSI Maximum inlet pressure: 70 PSI Maximum working temperature: 180 degrees Fahrenheit Carton dimension: 14" high, 12" wide, 24" long.
Please Contact us for shipping quote at http://www.clrmarine.com/Contact_Us
|
1794.60 |
|
|
Flotec FP5230 Cast Iron Sprinkler Pump 1 HP
Powerful 1 HP cast iron sprinkler pump moves up to 45 gpm. Perfect for sprinkler systems or water transfer applications.
FEATURES
Superior performance at depths-to-water of 25' or less Ideal for larger sprinkler systems and water transfer
Rugged cast iron construction Voltage-selectable to run on 115v or 230v
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1
MAXIMUM CAPACITY: 45 GPM
FLOW at 10' LIFT and 30 PSI: 35 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 50 psi
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 8.8 amps on 230v / 16.6 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 25 amp on 115v
MAXIMUM WATER TEMPERATEURE: 140 F (60 C)
|
761.04 |
|
|
Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP
Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.
KEY FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install dual voltage (115v/230v) motor
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8.8 GPM
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM
MAX PSI: 56 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
MINIMUM SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.4 amps
VOLTAGE: 115v/230v (preset to 115v), 60 Hz
RECOMMENDED BREAKER: 15 amp
LIQUID TEMP RANGE: 32°F-140 °F (0°C-60 °C)
JET KIT: included
|
433.55 |
|