|
Flotec Portable Utility Booster Pump
Manages a variety of home applications including sprinkling, pressure boosting and dewatering.
Can be used as a portable sprinkler pump
Ideal for boosting pressure to wash cars, boats and farm equipment
115V air cooled motor and has a 1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2 HP
MAXIMUM PRESSURE: 62 PSI
MAXIMUM CAPACITY: 10.3 GPM
FLOW at 10' SUCTION LIFT and 30 PSI: 5.1 GPM
SWITCH TYPE: No Switch (Manual Operation)
SUCTION SIZE: 1" (ships with garden hose adapter)
DISCHARGE SIZE: 1" (ships with garden hose adapter)
MAXIMUM SOLIDS HANDLING SIZE: .06"
AMP DRAW (full load): 7 Amps
CORD LENGTH: 6' w/ 3-prong grounded plug
VOLTAGE: 115v AC, 60 Hz
|
386.88 |
|
|
For many years, Jabsco Water Pressure Pumps have been the preferred system for cleaning marine vessels, making it an industry standard. That's because all Jabsco products are specifically designed to fit the expressed needs of boat builders and enthusiasts alike.
Features:
-High pressure jet blasts mud and silt from anchor chain and decks
-Waterproof, sealed motors
-Dry running capability
-Thermal overload protection automatically stops the motor if it overheats
Specials Closeouts Remanufactured Rebates
|
|
|
Jabsco's NEW VFlo Water Pressure Pump, Quiet With A Constant Flow
The new variable flow, constant water pressure pump now featuring the revolutionary new technology, designed to automatically diagnose and monitor all aspects of your pump and water pressure system performance to prevent system failure. V-FLO is powered by a new variable speed drive that delivers the exact amount of water flow needed to perform the variety of onboard delivery tasks.
Specials Closeouts Remanufactured Rebates
|
|
|
Flotec FP2211 2-Wire 4 Inch Submersible Well Pump, 115 Volts 1/2 HP
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 150ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
WARRANTY
3 year limited warranty
HORSEPOWER: 1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 115v, 60 Hz
NUMBER OF WIRES: 2 plus ground
BODY CONSTRUCTION: Stainless Steel and Thermoplastic
MAXIMUM CAPACITY: 13.6 GPM
OPERATION RANGE: 20' to 150'
MAXIMUM DEPTH-TO-WATER: 150'
MAX PSI: 105 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4" NPT
RECOMMENDED BREAKER: 25 amp
|
573.75 |
|
|
Flotec FP2212 2-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 150ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
3 year limited warranty
HORSEPOWER: 1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 2 plus ground
BODY CONSTRUCTION: Stainless Steel
MAXIMUM CAPACITY: 13.6 GPM
OPERATING RANGE: 20' to 150'
MAXIMUM DEPTH-TO-WATER: 150'
MAX PSI: 105 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4" NPT
RECOMMENDED BREAKER: 10 amp
|
593.25 |
|
|
Flotec FP3212 3-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP, 10 GPM
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 150ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
3 year limited warranty
HORSEPOWER: 1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 3 plus ground
BODY CONSTRUCTION: Stainless steel
MAXIMUM CAPACITY: 14 GPM
OPERATING RANGE: 20' to 150'
MAXIMUM DEPTH-TO-WATER: 150'
MAX PSI: 105 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4" NPT
RECOMMENDED BREAKER: 10 amp
|
588.75 |
|
|
Flotec 3-Wire 4 Inch Submersible Well Pump, 230 Volts 1.5 HP, 10 GPM
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 300ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
WARRANTY
3 year warranty
HORSEPOWER: 1-1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 3 plus ground
BODY CONSTRUCTION: Stainless Steel
MAXIMUM CAPACITY: 16 GPM
OPERATION RANGE: 40' to 300'
MAXIMUM DEPTH-TO-WATER: 300'
MAX PSI: 170 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4"
|
1510.56 |
|
|
Flotec Stainless Steel Waterfall Utility 1/2 HP
Stainless Steel construction with a ceramic seal design marks the FPOS4100X as the top of the line in the Flotec Waterfall/utility series of pumps.
KEY FEATURES
Complete stainless steel construction - superior corrosion resistance
Seal design - allows for continuous operation
High performance - ideal for waterfalls and streams
WARRANTY
2 year limited warranty
BODY CONSTRUCTION: Stainless Steel
HORSEPOWER: 1/2
MAXIMUM LIFT: 30'
MAXIMUM CAPACITY: 4100 GPH
FLOW at 10' LIFT: 3000 GPM
SWITCH TYPE: No Switch (Manual Operation)
DISCHARGE PIPE SIZE: 1-1/4" (ships with Adapter Fittings)
AMP DRAW (full load): 7.2 Amps
CORD LENGTH: 15'
VOLTAGE: 115v AC, 60 Hz
MAXIMUM WATER TEMPERATURE: 100°F (38°C)
|
681.75 |
|
|
Flotec N76-46P Pump Body
This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.
Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.
The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.
|
122.85 |
|
|
Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP
This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8 GPM
FLOW at 10' LIFT and 40 PSI: 6.4 GPM
MAX LIFT: 25'
MAX PRESSURE: 77 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.4 amps
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
432.90 |
|
|
Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP
This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 3/4
MAXIMUM CAPACITY: 12 GPM
FLOW at 10' LIFT and 40 PSI: 9.7 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 78 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 6.1 amps on 230v / 12.2 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
511.50 |
|
|
Flotec FP4222 Cast Iron Convertible Jet Pump 3/4 HP
Cast iron convertible jet pumps can be used in shallow or deep well applications in " diameter wells or larger and are pre-set for 30-50 PSI operation.
KEY FEATURES
Superior performance at depths to water of 100' or less
Rugged, heavy-duty pump housing
Ready-to-install 230 volt motor - see manual for 115 volt conversion
Pressure switch pre-wired with 30-50 PSI pressure setting
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 3/4
MAXIMUM CAPACITY: 11.9 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 10.8 GPM (shallow setup)
MAX LIFT: 25' w/ shallow setup / 100' w/ deep well setup
MAXIMUM PRESSURE: 60 psi w/ shallow setup / 54 psi w/ deep setup
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 6.1 amps on 230v / 12.2 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
68.64 |
|
|
Flotec FP5512 Cast Iron Centrifugal Pump 1/2 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install 230 volt motor (dual voltage)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 22 GPM
MAX LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 36 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 4.7 amps on 230v / 9.4 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
RECOMMENDED BREAKER: 15 amp on 230v / 15 amp on 115v
|
440.70 |
|
|
Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9 GPM (shallow well setup)
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM (shallow well setup)
MAX LIFT: 25' w/ shallow well jet kit / 70' w/ deep well jet kit
MAX PSI: 62 psi (shallow well setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4"
MINIMUM SUCTION PIPE SIZE: 1-1/4"
DRIVE PIPE SIZE: 1"
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
516.00 |
|
|
Flotec FP5162 Thermoplastic Sprinkler Pump 1 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 55 GPM
FLOW at 10' LIFT and 30 PSI: 28 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 42 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
593.25 |
|