|
Stainless Steel Table Base w/Locking Pin
Stainless Steel Table Support with Locking Pull Pin
Tube Size: 1-5/8''
Flange Dia.: 6-1/4"
|
102.04 |
|
|
Stainless Steel Table Column
Stainless Type 304 Table Column with White Delrin Insert
12"Wx17-3/4"H
Tube Size: 1-5/8"
|
169.57 |
|
|
Polished Stainless Steel Table Pedestal 3" OD x 25-1/2" L
All of TACO's Z76-Series table pedestal columns are tapered on the bottom for a secure fit into the base while also allowing for easy removal and storage.
Features:
Available in satin anodized aluminum rib design or polished stainless steel
Available in three different lengths
Custom heights available based upon minimum order quantities
5-year limited warranty
Specifications:
Finish: Polished
Taper: Single
Material: Stainless Steel
Length: 25-1/2"
|
93.25 |
|
|
Single Swing Arm Bracket w/Locking Pin
Majestic has a versatile range of swing arm brackets. The ARM101 can be easily removed from the base plat so you can remove the TV and ARM when travelling in harsh conditions. You can also purchase an addition base plate if you would like to move the TV & ARM to a different location!
Majestic has a versatile range of swing arm brackets. The ARM101 can be easily removed from the base plate so you can remove the TV and ARM when travelling in harsh conditions. You can also purchase an addition base plate if you would like to move the TV & ARM to a different location!
The ARM101 is also compatiable with the Majestic locking pin. The locking pin is designed to lock your arm bracket against the wall during transit.
The ARM101 comes in Black and also has removable covers to allow you feed cable through so that your installation is nice and neat. The Vesa plate is designed for Majestic TV's and many other brands.
Note: It is recommended to remove the TV from the wall during off-road transit.
Adjustable angle: 10 degrees up/down
Maximum load: 15kgs
Suitable for TV sizes: 13" - 27"
Distance to wall: 70-235mm
|
131.93 |
|
|
Reel Hangers
Adjustable marine grade 316 stainless steel reel hangers securely store trolling reels on ceiling or gunnel. Fits most popular trolling reels. Hangers are easily adjusted to accomodate a wide range of reel sizes. Set includes Stainless Steel Snap-Lock Rod Holder.
Features:
Marine Grade 316 Stainless Steel hardware
Internal stainless steel spring loaded pins
Concealed fasteners
Mounts horizontally, vertically, or overhead
Adjustable widths
Includes snap-lock rod tip holder
3 year guarantee
Benefits:
Non-corrosive, ideal for interiors or exteriors
Spring-loaded to secure reels safely in place
Sleek, clean look showcases rod and reels
Versatile mounting options sure to fit any space
Adjustable widths for a customized fit
Mating rod tip holders feature spring activated snap locks for secure closure even in rough seas
Scratch resistant vinyl interiors protect rod guides and tips
|
87.06 |
|
|
1/2" Hitch Lock with 5/8" Adapter - 1-1/4" or 2" Receiver - Barbell- Stainless Steel
Make the tow vehicle and trailer more secure by keeping them locked up tight with a CURT hitch lock. Like a hitch pin and clip, a hitch lock is designed to be inserted into the fastener hole in the side of a receiver tube to hold a ball mount or hitch-mounted accessory in place. While a CURT hitch pin does offer sufficient strength for keeping a ball mount firmly attached, a CURT hitch lock goes one step further.
CURT hitch locks allow users to lock the ball mount into the trailer hitch, deterring theft and preventing anyone from detaching a trailer from the ball mount and towing away from the property without permission. This CURT hitch lock features a barbell design with a stainless finish and comes with a 1/2" pin diameter and a 5/8" diameter adapter sleeve. This allows it to be used on either a 1-1/4" or 2" receiver tube size. CURT barbell hitch locks are comprised of a pin with two end caps and a round locking mechanism. This hitch lock is key-operated and activated with a simple 1/4-turn. Also, the deadbolt hitch lock comes with a watertight dust cap to keep out the elements and prevent corrosion.
For the ultimate towing security, a hitch lock and coupler lock used together will provide security at both the vehicle-side and trailer-side of the towing setup. For a boat, ATV, or camper, keep the toys more secure with CURT hitch locks.
Features:
1/2" diameter pin fits 1-1/4" x 1-1/4" receiver tubes
5/8" adapter sleeve allows mounting in 2" x 2" receiver tubes
Stainless steel construction for lasting rust resistance
Easy-to-operate, 1/4-turn lock activation
A watertight dust cap prevents internal corrosion
Includes two keys for added convenience
Specifications:
Finish: Polished stainless
Hub Warehouse: D25
Material: Stainless steel
Part Type: Hitch lock
Pin Diameter: 0.5 and 0.625 inches
Receiver Tube Size: 1-1/4 or 2 inches
Warranty: Limited lifetime warranty (one-year finish, one-year parts)
|
42.58 |
|
|
Swivel Base Rod Holders
RH575
Standard Angle 30°
Stainless Steel Flush Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
162.70 |
|
|
Swivel Base Rod Holders
RH575XL
Standard Angle 30°
Stainless Steel Flush Mount w/ Swivel Base Extra Long
This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
162.07 |
|
|
Swivel Base Rod Holders
RH579
Half Angle 15°
Stainless Steel Flush Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
162.70 |
|
|
Swivel Base Rod Holders
RH579XL
Half Angle 15° Extra Long Tube
Stainless Steel Flush Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
180.77 |
|
|
Stainless Steel Angle Base Deck Hinge - Removable Pin
Deck Hinges are designed to mount horizontally and attach an eye end secured to tubing in Bimini top applications. Concave Hinges are designed to rail mount on 7/8” tubing. Angled Hinges are used for mounting items on slanted surfaces like sloped gunwales. 3/16” pin size. Constructed of UV stabilized injection molded nylon. Installs with two #10 FH fasteners (not included). Available in black or white.
|
10.18 |
|
|
Stainless Steel Angle Base Deck Hinge
Deck Hinges are designed to mount horizontally and attach an eye end secured to tubing in Bimini top applications. Concave Hinges are designed to rail mount on 7/8” tubing. Angled Hinges are used for mounting items on slanted surfaces like sloped gunwales. 3/16” pin size. Constructed of UV stabilized injection molded nylon. Installs with two #10 FH fasteners (not included). Available in black or white.
|
11.84 |
|
|
SSTH 14 HW MSI+ Stainless Steel Mega Thru-Hull 14-Pin
Measures: Depth/Temperature. Frequency: 83/200/455/800kHz and 1.2 MHz. SOLIX MEGA Side Imaging+, MEGA Down Imaging+, Dual Spectrum CHIRP stainless steel thru hull transducer. This transducer supports MEGA Imaging+/800kHz/455kHz and Dual Spectrum CHIRP 2D Sonar with a CHIRP range of 150-220kHz. Includes built-in temperature sensor, rugged composite design and 30’ cable.
|
772.79 |
|
|
Starlink Stainless Steel 1"-14 Threaded Adapter & Stainless Steel Ratchet Base
Features:
316L stainless steel Starlink adapter with a 1"-14 threaded ratchet base
The bottom of the adapter has 1”-14 threads with setscrew to lock in place
The top of the adapter is machined to fit the Starlink antenna post
The overall height is 7-1/2” (adapter with the ratchet base).
Base measures 2-1/2" x 3-9/16" with 4 holes for 1/4” bolts
Mount has a 3/8" hole for cable pass-through
|
240.00 |
|
|
Starlink Stainless Steel 1"-14 Threaded Adapter & Stainless Steel Fixed Base
Features:
316L stainless steel Starlink adapter with a 1"-14 threaded fixed base
The bottom of the adapter has 1”-14 threads with sets crew to lock in place
The top of the adapter is machined to fit the Starlink antenna post
The overall height is 4” (adapter with the 3” diameter fixed base)
|
144.00 |
|