Additional Wall Plate f/ARM101 An additional wall plate for the ARM101 so you can move the TV & ARM to a different location! This wall/base plate is designed for the ARM101 so you can move the TV & ARM to a different location! Note: It is recommended to remove the TV from the arm during off-road transit.

Adapter Plate f/200 x 100 VESA Conversion The Majestic AD200 is designed as an Adaptor plate for the end of a bracket with a VESA of 100x100, to fit to the back a flat screen TV with a VESA of 200 x 100. The Majestic AD200 is designed as an Adaptor plate for the end of a bracket with a VESA of 100x100, to fit to the back a flat screen TV with a VESA of 200x100. IMPORTANT: You should only use an adaptor plate with a bracket that is rated to hold the size and weight of your TV.  Especially if you intend on using a swing arm bracket. The Majestic range of brackets have a VESA of up to 100x100.  The AD200 acts as an adaptor plate which fits to the 100x100 VESA mount bracket, allowing you to use the 200x100 hole spacing to fit to the 200x100 VESA on the TV. Majestic do not recommend fitting a 32" TV to a swing arm bracket when being used in the mobile environment.  Majestic recommend pairing the AD200 with the BKT100 and will cover warranty on this combination.  

441 Backing Plate f/241 & 244 Mount Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super tough, rugged engineering grade nylon. *Stainless steel nuts & machine screws included. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

ROKK Midi Top Plate f/Garmin and Raymarine  A multi-position, fully adjustable mount for small electronic devices.  Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations. The RL-502 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features. Features: Engineered to withstand high shock loading. Device-specific top plate Technical Specifications: Material - ASA Plastic Dimensions (diameter) -  2.11" (53.8 mm) Compatible with the following products *Sold as an Individual

ROKK Midi Top Plate f/Raymarine, Lowrance and B & G A multi-position, fully adjustable mount for small electronic devices.  Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations. The RL-504 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features. Features: Engineered to withstand high shock loading. Device-specific top plate Technical Specifications: Material - ASA Plastic Dimensions (L x W) -  5.67" x 2.43" (144 x 61.75 mm) Compatible with the following products *Sold as an Individual

ROKK Midi Top Plate f/Humminbird and Raymarine A multi-position, fully adjustable mount for small electronic devices.  Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations. The RL-506 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features. Features: Engineered to withstand high shock loading. Device-specific top plate Technical Specifications: Material - ASA Plastic Dimensions (L x W) -  5.35" x 1.89" (136 x 48 mm) Compatible with the following products *Sold as an Individual

ROKK Midi Top Plate f/Garmin, Simrad and B & G A multi-position, fully adjustable mount for small electronic devices.  Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations. The RL-507 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features. Features: Engineered to withstand high shock loading. Device-specific top plate Technical Specifications: Material - ASA Plastic Dimensions (L x W) -  6.61" x 2.59" (168 x 65.7 mm) Compatible with the following products *Sold as an Individual

TP325 Top Plate f/Converting Merriman/Yacht Specialties Steering Systems to 12" Wide 1.25" Diameter AngelGuard 12" Top Plates are used for upgrading from an existing 1" diameter pedestal guard to a 1.25" StraightGuard or AngleGuard. Specifically designed for Converting Merriman or Yacht Specialties steering systems. 12" Top Plates Include: 316 Stainless Steel Mirror Polished Finish Precision Laser Cut

Vision Series Mounting Plate f/Raymarine Quantum, 2kW & 4kW Radar Domes With Edson's Vision Series Mounting System, you can select your desired Mounting Plate to best fit your electronics. Edson's 68551 Vision Series Mounting Plate is designed for Raymarine Radar Domes (Quantum, Quantum 2, RD418D, RD424D, RD418HD, RD424HD). Mounting Plates are required to complete an Edson Vision Series Mounting System. Base mount sold separately. 

APT-LB-GPS2-01 PowerTower® Center Mounted Light Bar and Wing Plate f/2 Antenna Installs navigation light in the center and provides two (2) antenna mounts for maximum visibility and performance. Compatible with: Scanstrut aft leaning PowerTower® radar mounts Features: All mounting holes predrilled for easy retrofit installation, attach using mounting bolts, no extra fastenings required Cables run internally via a watertight seal Technical Specifications: Material - Aluminum  Height - 19.76" (502mm) Mount Position - Center In the Box: Light bar Instruction manual *Sold as an Individual

WD-RAD-01 Top Plate f/PowerTower® Radar Mounts - 4° Enhance the performance of your radome with the rugged, marine-grade, UV stable wedge that angles the radar down 4° below horizontal to provide a level horizon for your radar when the boat is underway. Mounts between PowerTower® mount and base of radar. Compatible with: Garmin - Fantom 18, 24, GMR18HD / 18xHD / 18HD+, GMR24HD / 24xHD, GMR40 radars Humminbird - AS 21RD4KW, HB 2124 CHIRP radars Lowrance - HALO20, HALO20+, HALO24, LRA-1800 / RB714A / DX42, LRA-2400 HD radars Raymarine - QUANTUM (Q24C), QUANTUM 2 (Q24D), RD218, RD418/RD418HD, RD424/RD424HD radars Simrad - DX45, DX60 / DX64-S, GB40 / NX40/45 / NSE8/12, GB40 / NX40/45 / NSE8/12 / RB712A / DX42S, GB40 / NX40/45 / NSE8/12 DX64S radars Sitex - MDS-12 radar Features: Enhance the performance of your radome with the Universal Scanstrut 4° radar base wedge 4° Base Wedge for mounting under PowerTower® A rugged, marine-grade, UV stable wedge  Compatible with radomes from most radar manufacturers Technical Specifications: Material - Marine Grade Polymer Dimensions (L x W ) - 11.10" x 9.09" Angle - 4° In the Box: Wedge Base seal Instruction manual *Sold as an Individual

1.5" Ball Mount w/2.5" Round Base, Short Arm & 1.5" x 3" Plate f/Humminbird Helix 5 Only The RAM-202-153-B-202U consists of a round 2.5" diameter round base (Universal AMPs Hole Pattern), short double socket arm and 1.5" x 3" rectangular base. The rectangular base contains four holes with a center to center pattern of 1" x 2.5". For most applications, mount will support up to ten pounds. Features: Compatible Devices: Humminbird Helix 5 Center to Center Hole Pattern: 1" x 2.5" Weight Capacity: 10 lbs. Overall Height: 5.225" Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag. Hardware for mounting to device not included with purchase. Weight: 0.19 lbs.

Super Dynaplate f/SSB Radio - 18" x 6" x 1/2" Create a proper bonding and grounding system using Dynaplate grounding shoes to reduce the risk of serious hull damage and electrical shock associated with boat lightning strikes by providing a direct, controlled high-capacity path for lightning dissipation. SSB and AM radio transmitters rely upon a proper size ground to operate to their designed capacity. A Dynaplate grounding shoe helps provide a large solid surface (the water surrounding the boat) to "push off" from. This is technically known as "counterpoise" and is the other necessary half of the antenna system. The bronze Dynaplate material also serves as the next sacrificial metal on the galvanic scale after the zincs, providing another buffer against corrosion of stainless steel parts. Features: Easy to clean with wire brush Conforms to ABYC standards Mounting hardware included Gold plated mounting bolt Bronze mounting nuts Copper washers WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Gunnel Mount Backing Plates f/88502 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.