ME-52 2 Channel Amplifier - 50 Watts The ME-52 is a compact 2-channel 50-watt audio amplifier with separate volume control. This unit is designed for adding additional speakers to an existing system or as a separate zone amp. Features:  To add additional loudspeakers to a current audio system To provide amplification for a separate audio zone Powers up to four (4) - 4ohm speakers Internal distortion limiting circuits Dedicated gain level control External volume control with ON/OFF switch included Specifications:  Number of Channels - 2  Speaker Impedance - 2-8 ohm 2 Ohm RMS Power - 2 x 25 W 4 Ohm RMS Power - 2 x 15 W Frequency Response - 20Hz-20kHz Dimensions (W x H x D) - 4-3/16" x 1-9/16" x 4-7/8" (106mm x 39mm x 124mm)  Volume Control Cable Length -  114" (290 cm) *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

ME-60 4 Channel Amplifier - 120 Watts The ME60 is a four channel 120 Watts RMS audio amplifier of delivering up to 30W RMS per channel.  It has a compact, water resistant design that allows for flexible mounting possibilities, and makes it simple to expand the audio system capabilities for any installation. Features: To add additional loudspeakers to a current audio system To provide amplification for a separate audio zone Powers up to eight (8) 4ohm speakers Internal distortion limiting circuits Dedicated gain level control External volume control with ON/OFF switch included Rear channels switchable from full range to powered sub out Specifications: Number of Channels - 4 Speaker Impedance - 2-8 ohm 4 Ohm RMS Power - 4 x 20 W 2 Ohm RMS Power - 4 x 30 W Frequency Response - 20Hz-40kHz Dimensions (W x H x D) - 6.9" x 4.5" x 1.4" (175mm x 115mm x 35mm)  Volume Control Cable Length - 114" (290 cm) *Sold as an Individual  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

ME-6005D 5 Channel Amplifier - 600 Watts Features: Waterproof IP5 Pigtail wire harness and connection High-efficient full range class D operation Selectable high-level and low-level input Signal sensing and 12V remote out short thermal and overload protection DIP switchable crossover Gain control for front and rear channel Switchable mode for 4-channel model: 2CH/4CH Specifications: Number of Channels - 5 4 Ohm RMS Power - 50W x 4 + 150 x 1 2 Ohm RMS Power - 75W x4 + 300 x 1 Frequency range: 20Hz-20KHz Dimensions (W x H x D) 11.4" x 4" x 1.75" (290mm x 102mm x  44.5mm) *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Select S-1100.2 2 Channel Amplifier - 1800W The SELECT series of amplifiers by DS18 is known for two things - legendary power and striking elegance.   This brushed aluminum amplifier adds a nice touch of sleekness to your sound system.  Each amplifier has adjustable crossover settings, gain control, and Hi/Lo pass filters to deliver powerful and accurate sounds that will make you feel like you’re in a concert. Own an elegant amplifier that provides awesome power and amazing reliability. Features: Surface mount component technology Audio precision quality control verification Multilayer PCB trace layout Clipping, power, and protection LED indicator Short circuit, thermal, and voltage protection Precise filters so you can get the perfect sound from your speakers Technical Specifications: Number of Channels - 2 Frequency Response - 20Hz - 200KHz 2 Ohm RMS Power (14.4V) Per Channel - 2 x 80W 4 Ohm RMS Power (14.4V) Per Channel - 2 x 60W Signal-to-Noise Ratio - >90dB Product Dimensions: (L x W x H) - 7.4" x " x 1.87" (18.8 x 5.83 x 4.75 cm) *Sold as an Individual

Candy-X2B 2 Channel Amplifier - 800W Small, compact, and powerful is what the DS18 Candy-X1B amplifier is all about.  Just like edible candy, we have many different flavors to choose from to give audio enthusiasts goosebumps when they turn it up.  Instead of making your mouth tingle, DS18 Candy Amplifiers make your ears tingle with pleasure when you hook them up to any line of pro audio, marine, and power sports audio. These amps not only have the power to keep your speakers at maximum wattage efficiently, but they are also very small and compact in design so they can be mounted almost anywhere and still not have to worry about the room!  DS18 Candy amplifiers are perfect for people who want a very small audio footprint with also having all the benefits of a huge amplifier putting out lots of power in a small package. Features: One of our most popular lines of automobile amplifiers because of its power output to size ratio Small and powerful design that gives it a wide range of versatility because of its size High-grade components made to stand the test of time and give you loud sound on demand RCA and Hi/Lo inputs so you can integrate this amp into your factory audio system easily Technical Specifications: Number of Channels - 2 Frequency Response - 20Hz - 20KHz 2 Ohm RMS Power (14.4V) Per Channel - 2 x 120W 4 Ohm RMS Power (14.4V) Per Channel - 2 x 80W Signal-to-Noise Ratio - >100dB Product Dimensions: (L x W x H) - 7.08" x " x 1.87" (18.0 x 12.7 x 4.75 cm) *Sold as an Individual

HYDRO Full Rangle Digital Marine 2-Channel Amplifier - 600W Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated  amp that has a small footprint and also make great power.  DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This 4 channel amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp.  All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification. Features: Stable and reliable 4 layers PCB layout design IPX67 Waterproof for Powersports applications Ultra compact size for easy installation Audio precision quality control verification  Technical Specifications: Number of Channels - 2 Frequency Range: 50Hz - 250KHz Max Power - 900W  2 Ohm RMS Power Per Channel - 150W x 2 4 Ohm RMS Power Per Channel - 100W x 2 4 Ohm Bridged Power Per Channel - 300W x 1 Signal-to-Noise Ratio - 90 dB Dimensions (L x W x H) - 7.87" x 3.68" x 1.57" *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

APEX PA1502 2 Channel Amplifier 150W x 2 Designed to excel in extreme conditions (Waterproof, Dustproof, Freezeproof) these amps will thrive in the all weather. These amps are a game changer from their small size, robust power output, and pricing.  Suitable for small compact places, these amps will thrive in golf carts, side by sides, snowmobiles, motorcycles, and small water crafts (flats boats, tenders, jet skis, fresh and saltwater aluminum and fiberglass boats) among other applications. Features: RMS Power: 100Wx2@4-ohm/150Wx2 @ 2-ohm/300W x 1 @ 4-ohm Selectable Crossover: All-Pass, High-Pass or Low-Pass @ 60/80/120Hz Frequency Response: 20Hz to 20kHz Selectable Bass Boost: 0, 6, 12dB @ 45H (when low-pass selected) Signal to Noise Ratio: 85dB THD: <1% Fuse Rating: 25A Dimensions: 170mm x 85mm x 45mm

Gianneschi ECOINOX-2-CE-230/50 Water System 230V 50Hz

Amplifier Package with ME70BT & MA-8505W Speakers This kit includes the MA-8505W Titanium Series Speakers and the ME70BT IPX6 4-Channel Marine Amplifier. The amplifier and speakers are a perfect replacement or upgrade for existing speakers, and the speaker magnets will not interfere with navigation equipment. Poly-Planar MA-8505W 5" 200 Watt Titanium Series Speakers – White Features: Colorfast plastic frame withstands UV rays Anti-magnetic design Waterproof construction  Rugged powder-coated stainless steel grill 3-way design with mylar tweeter & midrange ASTM UV & Salt Spray Test meets or exceeds 600hrs ME70BT IPX6 4-Channel Marine Amplifier Features: Remote display keypad 4x45 Audio power out 100 Meter Bluetooth range Phone/Android charging USB Music Player AUX input NMEA 2000® certified Multiple EQ preset options Backlit 3-line display with adjustable illumination MA-8505W Specifications: Type - 3-way Coaxial with tweeter Cone Size - 5" (152mm) Peak Power - 200 watts Continuous Power - 100 watts Speaker Impedance - 4 ohm Weight -1.85 lbs per speaker Mounting Depth -  2-7/16" (62mm) Outside Grill - 6" (153mm) Cutout - 4 1/2″ (115mm) Kit Includes: ME70BT IPX6 4-Channel Marine Amplifier (2) Poly-Planar MA-8505W 5" 200 Watt Titanium Series Speakers - White This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

SG-24DA61500 Signature Series 1500W - 6 Channel Amplifier - 24V The Signature Series 24-volt 6-channel marine amplifier is designed for boats operating on 24-volt electrical systems. With a peak power of 1500-watts, it provides incredible power delivery to your onboard audio entertainment. The plug-and-play setup allows for easy installation without the need for an additional power adaptor. Fusion Signature Series amplifiers are purpose-built for the marine environment. Boasting some of the most impressive environmental protection available, they deliver a Signature performance on the water like never before. Features: Class-D Amplifier Technology:  The highly efficient Class-D design provides 1500-watt peak power while drawing less current than a standard Class-AB amplifier.  This design provides increased efficiency and power output to your speakers and subwoofers, letting you enjoy your music for longer without needing to worry about battery drain. 1500-Watt Peak Power:  With a peak power of 1500-watts, you can easily power up to 6 pairs of speakers OR up to 4 pairs of speakers and 1 subwoofer. Marine-Ready Design with Conformal Coated PCBs:  Extending the life of your amplifiers, the Signature Series amplifiers are designed specifically for marine use with conformal coated PCBs to provide extra protection from the marine elements. Rigid Aluminum Alloy Heat Sink:  Molded to form a singular die-cast chassis, the fin layout is calculated with precision to increase the surface area of the heat sink and improve heat dissipation. Stainless Steel Mirror Finish:  The polished stainless steel control panel cover conceals and helps protect all cable connections and the settings control panel while providing an attractive finish to complement any installation. Speaker Configuration:  Whether you require 2 ohms per channel or 4 ohms bridged, the Signature Series amplifier has your installation options covered to achieve optimum output levels. Connect up to 2 speakers per channel (2 x 4 ohm speakers in parallel) with the SG-24DA61500. Zone Designation:  To align with the Fusion Entertainment System Zone philosophy, the input and output connections are labeled as zones. Technical Specifications: Frequency Response : 10 Hz to 40 kHz (-3dB @ 4 Ohm rated power) Peak Power Output:  1500 W Rated Power Output (4 Ohm):  100 W rms x 6 @ 28.8 V input < 1% THD + N (EIA/CEA-490A) Rated Power Output (2 Ohm):  140 W rms x 6 @ 28.8 V input < 1% THD + N (EIA/CEA-490A) Rated Power Output (4 Ohm Bridged): 280 W rms x 3 @ 28.8 V input < 1% THD + N (EIA/CEA-490A) Input Sensitivity:  0.3 V to 8 V rms, user adjustable Input Impedance:  7k Ohm nominal High-Pass/Low-Pass Full Range Filter:  Yes, user selectable Filter Cross-Over Frequency:  32 Hz to 320 Hz, user adjustable Bass-Boost:  0 to 9 dB, user adjustable (zone 3 only) Operating Voltage:  21.6 V to 32 V dc Remote Switch-On:  Yes - 6 V threshold Current Consumption (Standby): < 1 mA @ 28.8 V input Current Consumption (Idle):  < 1.25 A @ 28.8 V input Current Consumption (Max):  35 A @ 28.8 V input Fuse Rating:  3 x 20 A ATC Blade-Type (SAE J1171 Compliant) Protection Circuits:  Reverse-Voltage, Input Under/Over Voltage, Over-Temperature, Output Short-Circuit Operating Temperature Range:  0 to 50°C (32 to 122°F) Ingress Protection Rating:  Dry area installation only Dimensions:  420 mm (L) x 210 mm (W) x 57 mm (H) or 16-9-16" (L) x 8-1/4" (W) x 2-1/4" (H) Weight:  5.15 kg or 11.35 lb with cover Warranty:  3 years In the Box: Four 8-gauge, self-tapping screws 3 mm hex key (for the top cover and power terminals) 2.5 mm hex key (for the speaker terminals) Polishing cloth Spare J1171 compliant 20 A blade-type fuses (only included with 24-Volt Signature Series 6 Channel 1500-Watt amplifier) WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Poly-Planar PolyPlanar is the world's best known designer and manufacturer of waterproof and corrosion proof audio systems and outdoor speakers for marine, outdoor, deck, pool, patio, and boating applications. PolyPlanar is the Waterproof Marine Audio System with the Concert Hall Sound. Keep in mind Poly-Planar takes as much pride in their speakers as you take in your boat, deck, or pool.

MA754AM 4-Channel Amplifier - 75W The marine A754 4-channel amplifier delivers a powerful 75-watt RMS to each of the front and rear speakers in a boat. You can also bridge the amp to 2-channel mode to drive a couple of subs with a 200-watt RMS or 3-channel mode to drive both a pair of full-range speakers and a subwoofer. Speaker-level inputs allow this amplifier to integrate into almost any system, even one using a marine factory radio. Separate high-pass and low-pass crossovers on the front and rear channels allow users to dial in the perfect roll-off to best suit speaker placement and cabin acoustics. Features: Compact size High and low-level input Variable crossover and bass boost Low noise and distortion Input Level Control Full on-board protection   Phase Switch RBC wired remote Class D amp technology Turn-on mode General Specifications: 4-channel marine amplifier 75 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms) 200 watts RMS x 2 at 4 ohms in bridged mode (4-ohm stable in bridged mode) Variable high- and low-pass filters (32-320 Hz, 12 dB/octave) on front and rear channels Preamp and speaker-level inputs Preamp outputs Fuse rating 30A x 2 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier Dimensions (W x H x D) 320mm x 51.3mm x 180mm (12-5/8” x 2-1/16" x 7-1/8”) What’s in the Box: One marine A754 4-channel amplifier 4 Bare wire-to-RCA adapters Four 30A ATO fuses (2 installed, 2 spare) Two JBL stickers Owner's Manual 4 Mounting screws (M4 x 53mm) 1 logo badge

ME70BT IPX6 4-Channel Marine Amplifier Features: Remote display keypad 4x45 Audio power out 100 Meter Bluetooth range Phone/Android charging USB music Player AUX input NMEA 2000® certified Multiple EQ preset options Backlit 3 line display with adjustable illumination This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PA D5000.5 PAD Series 5-Channel Amplifier - 500W When install space is at a premium, but your sound system demands plenty of power to realize its full potential, Polk Audio’s new super-efficient D Series amplifiers are a very cool solution.  Polk's PA D5000.5 5-channel amplifier may be small, but it can power your complete system, sending 70 watts RMS to each of your front and rear speakers and up to 500 watts RMS to a sub.  Or, you can switch this little beast to 3-channel mode to drive a couple high-level components with 200 watts RMS each and still have that 500 watts RMS left over for the bass.  However you use it, this amplifier will fit in almost any location. Separate high- and low-pass filters on the front and rear channels allow this versatile amp to run a variety of speaker systems, like bi-amped mid-bass and tweeter components, or two front speakers and a sub. Features: Super-Efficient Class D Bridgeable Design - Runs cooler than conventional amps.     High-Speed MOSFET Switching power supply.  Front and rear level controls. Protection - thermal, DC offset, reverse polarity and short circuit. Nickel-plated wire terminals and RCA connectors. Stainless steel hardware. Technical Specifications: Number of Channels - 5 Frequency Response - 20Hz - 20KHz 2 Ohm RMS Power (14.4V) Per Channel - 4 x 100W, 1 x 400W 4 Ohm RMS Power (14.4V) Per Channel - 4 x 70W, 1 x 200W 4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 200W Signal-to-Noise Ratio - >105dB Product Dimensions (with panels) (H x W x D) -1-13/16'' x 13-5/16'' x 6.75'' *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

PA D4000.4 PAD Series 4-Channel Amplifier - 400W When install space is at a premium, but your sound system demands plenty of power to realize its full potential, Polk Audio’s new super-efficient D Series amplifiers are a very cool solution.  Polk's PA D4000.4 4-channel amplifier may be small, but it can power your front and rear speakers with up to 125 watts RMS each.  Or, you can switch this little beast over to 2-channel mode to drive a couple subwoofers with up to 200 watts RMS each.  However you use it, this amplifier will fit in almost any location. Separate high- and low-pass filters on the front and rear channels allow this versatile amp to run a variety of speaker systems, like bi-amped mid-bass and tweeter components, or two front speakers and a sub. Features: Super-Efficient Class D Bridgeable Design - Runs cooler than conventional amps.     High-Speed MOSFET Switching power supply.  Front and rear level controls. Protection - thermal, DC offset, reverse polarity and short circuit. Nickel-plated wire terminals and RCA connectors. Stainless steel hardware. Technical Specifications: Number of Channels - 4 Frequency Response - 20Hz - 20KHz 2 Ohm RMS Power (14.4V) Per Channel - 4 x 200W 4 Ohm RMS Power (14.4V) Per Channel - 4 x 125W 4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 400W Signal-to-Noise Ratio - >105dB Product Dimensions (with panels) (H x W x D) -1.81'' x 10.94'' x 6.75'' *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.