Freedom HF 1055 Inverter Charger - 120VAC 55A 12VDC The new generation Freedom HF is equipped with quick-connect AC terminals and ignition lockout capability. The quick-connect AC terminals enable quick installation eliminating the need for strain relief clamps. The ignition lockout feature helps to minimize battery drain by disabling the inverter when the ignition is turned off. The Freedom HF Inverter/Charger is one of the smallest, lightest, and most affordable inverter/chargers in the market today. The Freedom HF Inverter/Charger features modified sine wave output and is designed to operate entertainment systems and small appliances in boats, RV's and trucks. The Freedom HF is available in three models: 1000 watts with a 20-amp charger, 1000 watts with a 55-amp charger and 1800 watts with a 40-amp charger. Multistage charging helps ensure that batteries are recharged quickly and efficiently. All models are equipped with a built-in automatic transfer switch and dual GFCI receptacle. Detachable digital remote control panel display provides precise system information and can be mounted at a convenient location for remote monitoring. Some of the key feature enhancements include quick-connect AC terminal block on both AC input and output for incredibly easy installation. The ignition lockout feature minimizes battery drain by disabling the inverter when the ignition is turned off. Product Features: Input Voltage: 12V AC Output: GFCI and/or Hardwire Designed to power demanding loads such as microwave ovens, TVs, DVD players, small appliances and other electronic equipment Removable digital display pre-attached with 25' extension cable for remote system monitoring Ignition lockout feature helps to minimize battery drain Automatic three-stage battery charger Designed to be hardwired using quick-connect AC terminal blocks or by connecting AC through GFCI receptacles (included) Built-in 30-amp relay to automatically transfer between inverter power and incoming AC utility power Protection Features: Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Ground-fault protection ETL certified to UL458 for use in mobile RV and commercial applications WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Freedom HF 1000 Compact inverter/charger to power the comforts of home on your boat, RV, or truck With modified sine wave output, Freedom HF 1000 inverter/charger is designed to run entertainment systems and small appliances in smaller boats, RV's and trucks. The Freedom XMIC inverter/charger is the smallest, lightest, and least expensive model in the Xantrex lineup. Freedom HF is designed for demanding marine and RV conditions. Temperature-controlled multistage charging ensures that your batteries are recharged safely and efficiently. Both models include an automatic transfer switch and a detachable digital remote control panel display that provides precise system information and can be mounted wherever you require the information. Product Features: Designed to power loads such as microwave ovens, TVs, DVD players, small appliances and other electronic equipment Removable digital display to provide system status Automatic three-stage battery charger Designed to be hardwired using a terminal strip, or by connecting AC through GFIC receptacles (Included) Built-in 30-amp relay to automatically transfer between inverter power and incoming AC utility power Protection Features: Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Ground-fault protection ETL listed for use in mobile RV and marine applications WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Freedom HF 1800 Compact inverter/charger to power the comforts of home on your boat, RV, or truck With modified sine wave output, Freedom HF 1800 inverter/charger is designed to run entertainment systems and small appliances in smaller boats, RV's and trucks. The Freedom HF inverter/charger is the smallest, lightest, and least expensive model in the Xantrex lineup. Freedom HF is designed for demanding marine and RV conditions. Temperature-controlled multistage charging ensures that your batteries are recharged safely and efficiently. Both models include an automatic transfer switch and a detachable digital remote control panel display that provides precise system information and can be mounted wherever you require the information. Product Features: Designed to power loads such as microwave ovens, TVs, DVD players, small appliances and other electronic equipment Removable digital display to provide system status Automatic three-stage battery charger Designed to be hardwired using a terminal strip, or by connecting AC through GFIC receptacles (Included) Built-in 30-amp relay to automatically transfer between inverter power and incoming AC utility power Protection Features: Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Ground-fault protection ETL listed for use in mobile RV and marine applications WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Remote for Freedom HF Series Inverter/Chargers Replacement panel for Freedom HF Series inverter/chargers. *Does not include connection cable. Compatible With: Freedom HF Series inverter/chargers Features: View key system information Configure and monitor important parameters and settings Conveniently view fault and error codes Technical Specifications: Input Voltage: 12V AC Output: GFCI and/or Hardwire In the Box: Remote panel Instruction manual *Sold as an Individual

Freedom X 1200 Inverter Truesine 1000W 120AC 12VDC Hardwire, Transfer The Xantrex Freedom X 1200 is engineered specifically to meet the needs of heavy-duty trucks and is ideal for installation in all types of commercial and recreational vehicles. This inverter provides up to 1200 watts of continuous utility grade, sine wave power from a battery bank and is designed to handle loads such as microwave ovens, TVs, DVD/Blu-ray players, and power tools. In addition, the Freedom X 1200's high-surge capability lets you handle many hard-to-start loads, including full-size residential refrigerators. The Freedom X 1200 has a built-in 30 Amp transfer switch that automatically transfers between inverter power and shore power from recreational facilities such as boat docks or campsites to ensure power is always available. If incoming shore power is interrupted by external events like brownouts, the Freedom X 1200 automatically becomes an independent power source that supplies utility-grade AC power to your loads. The Freedom X 1200 offers comprehensive built-in protection features to safeguard your batteries from the unnecessary drain while protecting your equipment. Features include selectable low battery shutdown voltage, low voltage shutdown delay timer, power save mode, low battery voltage alarm, and shutdown. The Freedom X 1200 also features configurable AC transfer speed, output frequency, and voltage, making it extremely versatile and the perfect blend of performance and cost. Features: Input: 12 VDC Output voltage: 120 VAC, 60 Hz Continuous Power: 1200W (10.0 A) Surge Power: 2400W (20.0 A) Output waveform: Pure sine wave Transfer relay: 30A Dimensions: 14.8 x 10.4 x 3.5 in (376 x 263 x 91 mm) Inverter weight: 10.4 lbs (4.7 kg) Shipping weight: 13.0 lbs (5.9 kg) Warranty: 2 years

Xantrex Freedom HF - NEW GENERATION                                  Is In Stock at CLR Marine A Xantrex inverter/charger is a combination of an inverter, battery charger and transfer switch into one complete system. When AC power is available, the inverter/charger recharges the house batteries. It also allows any surplus AC power to pass through and power downstream AC loads, such as a television set or microwave oven. When AC power is disconnected, the unit inverts DC battery power into AC electricity.

Conext Combox Communication Box f/Freedom SW Series Inverters/Chargers The Conext ComBox Freedom SW provides an overall view of system performance for mobile power monitoring systems such as RV, Marine vessels, construction and other heavy duty applications. The ComBox Freedom SW lets you configure the system and devices, monitor performance, and access data logs through a web based application on a laptop or Android tablet app. An easy to read icon based display screen (tablet not included) shows graphical representation of energy flow between utility power, generator power, Freedom SW Inverter/ Charger, RV house battery system and AC loads. The ComBox FSW module connects to your Freedom SW via Xanbus cables and optionally to an external wireless router providing wireless access to the ComBox FSW app on your Android tablet or laptop near your RV. User Level Access: Control Inverter - enable/ disable Control Generator - off/ on/ auto Real-time clock - when set, keeps time for the entire system Shore breaker size (selectable range 5-50A) Provides a more comprehensive and user friendly interface as an alternative to the SCP system control panel Data logging Battery charge (Watt-hours) Load consumption (Wh) Utility grid input (Wh) Generator input (Wh) Admin Level Access: Setup - Advanced access for installers and technician support Hardware Features: Powered by Xanbus network (Freedom SW Inverter/ Charger, or supplied AC/ DC adapter) Accepts USB thumb drive & micro SD card that provides additional data storage Compact, light weight, easy to install Non-volatile memory - preserves the latest Conext ComBox settings if power is interrupted or network communication is disrupted Firmware storage and upgrade capability - upgrade firmware for Xanbus-enabled devices on the network *ComBox FSW is compatible with Freedom SW Inverter/Charger, SCP (system control panel) & AGS (automatic generator start) WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Status and Freedom Inverter/Charger Remote Control Provides Valuable Inverter/Charger System Monitoring and Control The Freedom Remote Control Panel (part#84-2056-01) allows you to control your Freedom Combi, Freedom 458 and Freedom Marine Series Inverter/Charger system from any convenient location. It is easy to read, operate and install, and all controls can be accessed directly from the front panel. Note: Not for Freedom HF or Freedom SW Series. Product Features Independent invert and charge on/off controls Push button control of power sharing, equalizing, battery set-up Multi-colored LED displays battery state of charge, fault conditions, AC input, DC voltage and DC amperage LED warning indictors for low battery and overload warning Splash resistant design Incoming AC breaker selection allows programmable power sharing Easy to install 25' Cable One year warranty Note: The 24-volt models of Freedom Combi inverter/chargers require a different Freedom Remote the Freedom Remote - 24V SKU 82-0101-04 WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Freedom XC Pro 2000 Inverter/Charger - 2000W - 100A - 120V - 12V 2000 Watt pure sine wave inverter with 100 Amp built-in lithium-ion battery charger and transfer switch in a compact, lightweight footprint. Configure and monitor system performance via Bluetooth app available on the optional Bluetooth remote panel The Freedom XC PRO inverter/charger, supporting RV-C and J1939 protocols, is the most versatile and flexible AC power solution in the market today. It also features a 100 amp (2000W model) / 150 amp (3000W model) battery charger and offers all of the configurable features of the Freedom XC series inverter/charger in a compact, light weight package. It cranks out full output in invert or charge mode from -4°F (-20°C) - 104°F (40°C) for operation in all climate temperatures. The extended surge rating enables compressor loads such as an A/C or a fridge to start reliably. Features: Extended Surge Rating: Surges to 2X continuous power for 5 seconds for motor loads True Sine Wave AC Power: For operation of sensitive and motor loads Ignition Control: Feature to turn inverter on/off via a 12 VDC signal and to minimize battery drain by switching the inverter off when the ignition key is turned off Wide 10-18 VDC Input Range: Ensures inverter operation on high voltage alternators found on many new vehicle chassis Built-in 50A AC Transfer Relay: Senses when outside AC Power is present and transfers the load from the inverter to the source of incoming power (shore or generator) Power Factor corrected Multi-Stage: Utilizes less shorepower when charging batteries. This frees up more usable AC power for running electrical devices and appliances Programmable: Configurable 3 stage temperature compensated battery charge algorithm for optimal charging of almost any battery type up to 18V Specifications: Continuous Power: 2000 Watts Continuous Current: 16.7 Amps Surge Power: 4000 Watts Frequency: 60 (or 50) Hz (selectable) Output Voltage: 108, 110, 120 Volts AC (selectable) Input Voltage: 12 Volts DC nominal Safety: ETL listed to CSA 107.1, UL458 (UL458 Marine Supplement with optional drip shield, part number 808-1050) Dimensions: 15.4" x 10.8" x 4.9" Unit weight: 17.1 lbs 2 year warranty

Freedom XC Pro 3000 Inverter/Charger - 3000W - 150A - 120V - 12V A true sine wave inverter with a built-in lithium-ion battery charger and transfer switch in a compact, lightweight footprint. Configure and monitor system performance via Bluetooth app available on the optional Bluetooth remote panel (# 808-0817-02). The Freedom XC PRO inverter/charger, supporting RV-C and J1939 protocols, is the most versatile and flexible AC power solution in the market today. It also features a 100 amp (2000W model) / 150 amp (3000W model) battery charger and offers all of the configurable features of the Freedom XC series inverter/charger in a compact, light weight package. It cranks out full output in invert or charge mode from -4°F (-20°C) - 104°F (40°C) for operation in all climate temperatures. The extended surge rating enables compressor loads such as an A/C or a fridge to start reliably.  Features: Extended Surge Rating: Surges to 2X continuous power for 5 seconds for motor loads True Sine Wave AC Power: For operation of sensitive and motor loads Ignition Control: Feature to turn inverter on/off via a 12 VDC signal and to minimize battery drain by switching the inverter off when the ignition key is turned off Wide 10-18 VDC Input Range: Ensures inverter operation on high voltage alternators found on many new vehicle chassis Programmable AC Under-Voltage (85-110VAC) Shutdown: Feature ideal to operate under weak shore power or generator input Built in 50A AC Transfer Relay (3KW model): Senses when outside AC Power is present and transfers the load from the inverter to the source of incoming power Built-In Charger Features: Power Factor Corrected Multi-Stage Charging: Utilizes less shorepower when charging batteries. This frees up more usable AC power for running electrical devices and appliances and reduces the likelihood of tripping shorepower breakers Programmable: Configurable 3 stage temperature compensated battery charge algorithm for optimal charging of almost any battery type up to 18V Battery Equalization: Maximizes flooded battery life Dead Battery Charging Down to 0 Vdc Power Share: Prioritizes AC loads by reducing the charge current and maintaining the total input current to less than the breaker setting Easily configurable settings to charge any lithium ion battery

Freedom XC PRO Marine 2000W Inverter/Charger - 12V A true sine wave inverter with a built-in lithium-ion battery charger and transfer switch in a compact, lightweight footprint. Configure and monitor system performance via Bluetooth app available on the optional Bluetooth remote panel (# 808-0817-02). Seamless integration with Micro-C NMEA 2000 Connector. The Freedom XC PRO Marine inverter/charger, supporting CANbus NMEA 2000 protocol, is the most versatile and flexible AC power solution in the market today. It supports seamless integration with third-party monitoring and control systems. It also features a 100 amp (2000W model) / 150 amp (3000W model) battery charger and offers all of the configurable features of the Freedom XC series inverter/charger in a compact, lightweight package. It cranks out full output in invert or charge mode from -4°F (-20°C) - 104°F (40°C) for operation in all climate temperatures. The extended surge rating enables compressor loads such as an A/C or a fridge to start reliably. Features: Extended Surge Rating: Surges to 2X continuous power for 5 seconds for motor loads True Sine Wave AC Power: For the operation of sensitive and motor loads Ignition Control: Feature to turn the inverter on/off via a 12 VDC signal and to minimize battery drain by switching the inverter off when the ignition key is turned off Wide 10-18 VDC Input Range: Ensures inverter operation on high voltage alternators found on many new vehicle chassis Programmable AC Under-Voltage (85-110VAC) Shutdown: Feature ideal to operate under weak shore power or generator input Built-in 50A AC Transfer Relay (3KW model): Senses when outside AC Power is present and transfers the load from the inverter to the source of incoming power Built-In Charger Features: Power Factor Corrected Multi-Stage Charging: Utilizes less shorepower when charging batteries. This frees up more usable AC power for running electrical devices and appliances and reduces the likelihood of tripping shorepower breakers Programmable: Configurable 3 stage temperature compensated battery charge algorithm for optimal charging of almost any battery type up to 18V Battery Equalization: Maximizes flooded battery life Dead Battery Charging Down to 0 Vdc Power Share: Prioritizes AC loads by reducing the charge current and maintaining the total input current to less than the breaker setting Easily configurable settings to charge any lithium-ion battery This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Freedom XC PRO Marine 3000W Inverter/Charger - 12V A true sine wave inverter with a built-in lithium-ion battery charger and transfer switch in a compact, lightweight footprint. Configure and monitor system performance via Bluetooth app available on the optional Bluetooth remote panel (# 808-0817-02). Seamless integration with Micro-C NMEA 2000 Connector. The Freedom XC PRO Marine inverter/charger, supporting CANbus NMEA 2000 protocol, is the most versatile and flexible AC power solution in the market today. It supports seamless integration with third-party monitoring and control systems. It also features a 100 amp (2000W model) / 150 amp (3000W model) battery charger and offers all of the configurable features of the Freedom XC series inverter/charger in a compact, lightweight package. It cranks out full output in invert or charge mode from -4°F (-20°C) - 104°F (40°C) for operation in all climate temperatures. The extended surge rating enables compressor loads such as an A/C or a fridge to start reliably. Features: Extended Surge Rating: Surges to 2X continuous power for 5 seconds for motor loads True Sine Wave AC Power: For the operation of sensitive and motor loads Ignition Control: Feature to turn the inverter on/off via a 12 VDC signal and to minimize battery drain by switching the inverter off when the ignition key is turned off Wide 10-18 VDC Input Range: Ensures inverter operation on high voltage alternators found on many new vehicle chassis Programmable AC Under-Voltage (85-110VAC) Shutdown: Feature ideal to operate under weak shore power or generator input Built-in 50A AC Transfer Relay (3KW model): Senses when outside AC Power is present and transfers the load from the inverter to the source of incoming power Built-In Charger Features: Power Factor Corrected Multi-Stage Charging: Utilizes less shorepower when charging batteries. This frees up more usable AC power for running electrical devices and appliances and reduces the likelihood of tripping shorepower breakers Programmable: Configurable 3 stage temperature compensated battery charge algorithm for optimal charging of almost any battery type up to 18V Battery Equalization: Maximizes flooded battery life Dead Battery Charging Down to 0 Vdc Power Share: Prioritizes AC loads by reducing the charge current and maintaining the total input current to less than the breaker setting Easily configurable settings to charge any lithium-ion battery This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Freedom SW2524 230V Sine Wave Inverter/Charger - 2500W The Freedom SW 230V Inverter/Charger is a true sine wave inverter/charger that can be used for mobile, marine and commercial applications. The Freedom SW 230V Inverter/Chargers are designed to operate with a wide variety of generators and are capable of operating in parallel with a generator for short durations to assist with starting large loads. The Freedom SW 230V is a charger, and transfer switch in one electronic device. Features: As an inverter, the Freedom SW 230V provides true sine wave power for your microwave, entertainment system, computer, and other loads. This power is identical to the AC source provided from the utility grid (power company) Some of the benefits of true sine wave power include consistent cooking in your microwave, handling of sensitive loads such as your TV set, dimmer switches, and appliances with speed controls Highly versatile platform capable parallel stacking to increase power levels High efficiency true sine wave output to power sensitive electrical and electronic equipment Surge capacity to start difficult loads like well pumps, refrigerators, or A/C compressors Power factor-corrected (PFC) input minimizes AC input current required for charging, increasing AC pass-through capacity As a 24-volt charger, it has high output, multi-stage charging capability minimizing charging time WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Freedom SW3524 230V Sine Wave Inverter/Charger - 3400W The Freedom SW 230V Inverter/Charger is a true sine wave inverter/charger that can be used for mobile, marine and commercial applications. The Freedom SW 230V Inverter/Chargers are designed to operate with a wide variety of generators and are capable of operating in parallel with a generator for short durations to assist with starting large loads. The Freedom SW 230V is a charger, and transfer switch in one electronic device. Features: As an inverter, the Freedom SW 230V provides true sine wave power for your microwave, entertainment system, computer, and other loads. This power is identical to the AC source provided from the utility grid (power company) Some of the benefits of true sine wave power include consistent cooking in your microwave, handling of sensitive loads such as your TV set, dimmer switches, and appliances with speed controls Highly versatile platform capable parallel stacking to increase power levels High efficiency true sine wave output to power sensitive electrical and electronic equipment Surge capacity to start difficult loads like well pumps, refrigerators, or A/C compressors Power factor-corrected (PFC) input minimizes AC input current required for charging, increasing AC pass-through capacity As a 24-volt charger, it has high output, multi-stage charging capability minimizing charging time WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

The Freedom SW 2000 Inverter/Charger is offered with the GFCI (Ground Fault Circuit Interrupter) option to enable you to plug electronics directly on the inverter/charger. This ground fault protected AC output is also a requirement for certain mobile applications. The GFCI plate can be mounted directly and quickly on the Freedom SW 2000. WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.