SB-8-5 Junction Box Scanstrut's SB-8-5 Junction Box is perfect for installations if you need to create a waterproof connection for multiple electrical cables. Heavy-duty junction box manufactured from marine grade polypropylene and with features 5 screw-down terminals. Depending on the number of terminations required the terminal blocks can be individually fitted or blocked together.  Supplied with 5 modular terminal blocks.  Offering 5 terminations. Cables push fit into the terminals and are secured with a sprung leaf retention system that does not damage the wire.  The terminal can be removed for easy fitting of cables.  Features: Provides 5 screw-down terminals. Capacity for up to eight (8) cables to enter the box. Watertight Installation - Cables are quickly routed into the box through an IP66 elastomeric membrane, guaranteeing protection against water ingress. Upgradable to IP68 with use of SB-2G Cable Seals (sold separately)  Technical Specifications: Maximum cable size (diameter) - .50" (12 mm)   Maximum wire size - 16/1.5 to 11/4 Dimensions (L x W x H) - 3.35" x 3.35" x 2" (85  x 85 x 50 mm) Five (5) terminal block w/400 V rating and 32 A Color - Grey Material - Marine grade polypropylene In the Box: Junction box w/five (5) screw-down terminal block Mounting hardware Installation manual *Sold as an Individual

Scanstrut SB-8-10 Junction Box Scanstrut's SB-8-10 Junction Box is perfect for installations if you need to create a waterproof connection for multiple electrical cables. Heavy-duty junction box manufactured from marine grade polypropylene and features 5 screw-down terminals. Depending on the number of terminations required the terminal blocks can be individually fitted or blocked together.  Supplied with 10 modular terminal blocks.  Offering 10 terminations. Cables push fit into the terminals and are secured with a sprung leaf retention system that does not damage the wire.  The terminal can be removed for easy fitting of cables.  Features: Provides 10 screw-down terminals. Capacity for up to eight (8) cables to enter the box. Watertight Installation - Cables are quickly routed into the box through an IP66 elastomeric membrane, guaranteeing protection against water ingress. Upgradable to IP68 with use of SB-2G Cable Seals (sold separately)  Technical Specifications: Maximum cable size (diameter) - .50" (12 mm)   Maximum wire size - 28/0.08 to 12/3-3 Dimensions (L x W x H) - 3.35" x 3.35" x 2" (85  x 85 x 50 mm) Ten (10) terminal block w/600 V rating and 20 A Color - Grey Material - Marine grade polypropylene In the Box: Junction box w/ten (10) screw-down terminal block Mounting hardware Installation manual *Sold as an Individual

SB-2G Junction Box Cable Seal - 2 Pack Upgrade your Scanstrut Junction Box to IP67 Waterproof standard. This Cable Seal upgrade kit is available to upgrade your Junction Box to IP67.  The IP67 cable seals screw into the boxes at the cable entrance points and can accept cables from 0.15” to 0.48" (4 to 12mm). Features: Watertight installation - 100% waterproof with an IP67 rating. Dome-shaped profile provides a stronger, impact-resistant design and outer dome provides additional water shield. Compatible With: SB-8-5 Junction Box  SB-8-10 Junction Box Technical Specifications: Fits cable size (diameter) - .15" to .48" (4 - 12 mm)   Color - Grey Material - Marine grade polypropylene In the Box: Two (2) cable seals Mounting hardware Installation manual *Sold as a Pair

BX-2 Junction Box This BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms.  Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 1 Positions per Strip: 12 Max Wire Gauge: 16 Max Amps (per position): 6  Cable Entries: 8 Cable Diameter: 0.37 in. Box Size: 4.4 x 2.4 x 1.2 in. Box Size: 11.2 x 6.1 x 3.1 cm

BX-1 Junction Box This BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms.  Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 1 Positions per Strip: 6 Max Wire Gauge: 16 Max Amps (per position): 6  Cable Entries: 2  Cable Diameter: 0.25 in. Box Size: 2 x 2 x 1.2 in. Box Size: 5.1 x 5.1 x 3.1 cm

BX-3 Junction Box This BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms.  Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 2 Positions per Strip: 11 Max Wire Gauge: 14 Max Amps (per position): 10  Cable Entries: 2 Cable Diameter: 0.59 in. Box Size: 4.7 x 3.7 x 1.3 in. Box Size: 11.9 x 9.4 x 3.3 cm

Standard 4-Way Junction Box The OceanLED Standard Junction Box is a robust interconnect module that houses and protects electrical connections. This multi-outlet unit allows up to 4 underwater lights to be connected and is vDC powered. The box provides the transition from conduit to multi-cable via easy cable gland connector. Features: 12/24v DC IP66 4x Fused DMX outputs (10a max per output) Robust Polycarbonate Design Semi-transparent LID

PX-1 Junction Box This waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray. Connector Strips Installed in Boxes Molded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards. Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 1 Positions per Strip: 6 Max Wire Gauge: 16 Number of Cable Entry Ports: 5 Number of Cable Entries Installed: 3 Spare Cable Entries Provided: 2 Cable Diameter Range (inches): .14 – .81 Cable Diameter Range (mm): 3.5 – 20.5     Box Size (inches): 2.95 x 2.95 x 1.66     Box Size (cm): 7.5 x 7.5 x 4.2

PX-2 Junction Box This waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray. Connector Strips Installed in Boxes Molded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards. Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 2 Positions per Strip: 6 Max Wire Gauge: 16 Number of Cable Entry Ports: 7 Number of Cable Entries Installed: 7 Spare Cable Entries Provided: 0 Cable Diameter Range (inches): .14 – .81 Cable Diameter Range (mm): 3.5 – 20.5     Box Size (inches): 3.35 x 3.35 x 1.66     Box Size (cm): 8.5 x 8.5 x 4.2

PX-3 Junction Box This waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray. Connector Strips Installed in Boxes Molded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards. Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 2 Positions per Strip: 9 Max Wire Gauge: 16 Number of Cable Entry Ports: 7 Number of Cable Entries Installed: 7 Spare Cable Entries Provided: 0 Cable Diameter Range (inches): .14 – .99 Cable Diameter Range (mm): 3.5 – 25.5 Box Size (inches): 4.45 x 4.45 x 2.29     Box Size (cm): 11.3 x 11.3 x 5.8

X-Series DMX Junction Box For use in-conjunction with OceanLED Colours APP and DMX controller. Allows for up to 4 DMX connections to OceanLED Xtreme Series DMX Colours Lights per Junction Box. Can be linked to further DMX junction boxes to connect a series of LED Lights. Features: 12/24v DC IP66 4x Fused Power/DMX outputs (4A max power output) Built-in DMX terminator DMX input/output to allow multiple expansion To be used in conjunction with OceanLED Xtreme Series DMX Colours Robust Polycarbonate Design See-through lid to view connections Semi-transparent LID Specifications: Warranty: 2 years

OceanConnect Junction Box The OceanConnect is a waterproof (IP66) DMX-controlled, low-voltage DC (9–32V) junction box. The OceanConnect provides one power unit and four individually switched fused power outputs (6 amps per output) to connect DC-powered lights or other DC-switched units. The unit also supports powering and individual addressing of up to four DMX-controlled OceanLED X-Series lights.  Contents: 1x OceanConnect unit, including 4x 7.5A blade fuses 4x mounting screws 1x twin entry cable grommet 4x blanking plugs Specifications: Voltage: 12/24V DC (max 32V DC) Input/Output Cable Glands: 1x M20-Power In, 4x M16 - DMX In/Out, and Lights Out Power Input Terminals Wire Gauge: 8-20 AWG DMX In/Out, and Lights Out Terminals Wire Gauge: 12-28 AWG Light Outputs: DMX & Power- 4 x individual fused 6 Amp each max DMX Input: 1x DMX Input (to connect the DMX controller) DMX Output: 1x DMX Output (to link junction boxes in the chain) DMX Terminator: Onboard DMX terminator with an on/off switch Physical Specifications Dimensions (Including Cable Glands): 228mm x 174mm x 60mm (9" x 6.8" x 2.3") Enclosure: IP66-robust polycarbonate Weight: 270g

2-Way DMX Junction Box The 2-Way DMX Junction Box has been specifically developed to work in combination with OceanLED Sport Colors DMX lights and Explore E3 Colors DMX lights. Its primary role is to allow for the distribution of power and DMX signals within the vessel’s underwater lighting system. Using the 2-Way DMX Junction box, a Sport Colors DMX or Explore E3 Colors DMX system can be expanded to include up to 32 lights. The IP66-rated 2-Way Junction Box unit is made from robust polycarbonate materials and should be mounted in a protected area within the vessel. Features: Allow for the distribution of power and DMX signals within the vessel’s underwater lighting system

FI5002 NMEA2000 Junction Box The FI5002 is an NMEA2000 Certified, 6-Port Junction Box for use with for use with any NMEA2000 network. The FI5002 features 2 NMEA2000 backbone ports, as well as 6 NMEA2000 ports. It will support up to 2A or 40 (LEN) on a 12VDC network.The FI5002 will also support 24VDC networks. Features 2 NMEA2000 backbone ports 6 NMEA2000 ports Less than 2A power requirement on a 12VDC system WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Chirp Junction Box for Raymarine CP470 Type Connector Airmar adapter box for single-band or dual-band CHIRP tranducers, with Raymarine 11-pin connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.