|
1-In 2-Out Fused Distribution Block
Roswell's distribution blocks are machined out of solid brass alloy to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined brass inserts to accommodate multiple sizes of wire.
The Roswell 1-in-2-out distribution block is everything a boat's audio system has ever needed. Roswell's distribution blocks are machined out of nickel to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined nickel inserts to accommodate multiple sizes of wire.
Features:
Fused style distribution block
(1) 1/0 input with a 4 AWG reducer
High-impact plastic base and cover
(2) 4 AWG outputs with 8 AWG reducers
Dimensions:
Length: 4.00 inches (10.16 cm)
Width: 1.8125 inches (5.08 cm)
Height: 1.3125 inches (3.33 cm)
|
34.91 |
|
|
1-In 4-Out Fused Distribution Block
The Roswell 3-in 4-out distribution block is everything a boat's audio system needs. Roswell distribution blocks are machined out of nickel to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined nickel inserts to accommodate multiple sizes of wire.
Features:
Fused style distribution block
(3) 1/0 input with a 4 AWG reducer
High-impact plastic base and cover
(4) 4 AWG outputs with 8 AWG reducers
Dimensions:
Length: 4.00 inches (10.16 cm)
Width: 3.25 inches (7.62cm)
Height: 1.3125 inches (3.33 cm)
|
65.46 |
|
|
1-In 2-Out Ground Distribution Block
Roswell's distribution blocks are machined out of solid brass alloy to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined brass inserts to accommodate multiple sizes of wire.
The Roswell 1-in-2-out distribution block is everything a boat's audio system has ever needed. Roswell's distribution blocks are machined out of nickel to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined nickel inserts to accommodate multiple sizes of wire.
Features:
Ground-style distribution block
(1) 1/0 input with a 4 AWG reducer
High-impact plastic base and cover
(2) 4 AWG outputs with 8 AWG reducers
Dimensions:
Length: 4.00 inches (10.16 cm)
Width: 1.8125 inches (5.08 cm)
Height: 1.3125 inches (3.33 cm)
|
40.72 |
|
|
1-In 4-Out Ground Distribution Block
The Roswell 3-in 4-out distribution block is everything a boat's audio system needs. Roswell distribution blocks are machined out of nickel to provide rock-solid electrical connections and are protected by strong, injection-molded plastic covers. They are designed to accept both ANL and Mini ANL fuses for additional versatility and feature machined nickel inserts to accommodate multiple sizes of wire.
Features:
Ground-style distribution block
(3) 1/0 input with a 4 AWG reducer
High-impact plastic base and cover
(4) 4 AWG outputs with 8 AWG reducers
Dimensions:
Length: 4.00 inches (10.16 cm)
Width: 3.25 inches (7.62cm)
Height: 1.3125 inches (3.33 cm)
|
71.58 |
|
|
Bosworth 1.25 Tapped Outlet Bronze
|
105.79 |
|
|
Bosworth 1.25 Tapped Outlet Aluminum
|
78.98 |
|
|
VFDB4 MANL 4 Position Distribution Block with Cover
This compact distribution block from T-Spec will handle the high-current power distribution for your single source to four (4) smaller gauge power wires, ensuring that your wiring's connected securely, looking neat, and safely fused. T-spec's Universal Screw Design for securing the wires and mini ANL fuses to the block works with a variety of tools. Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover keeps the fuses and connections clean.
Fuses sold separately.
Features:
One (1) 1/0 to 4 AWG into four (4) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate Lock technology
In the Box:
One distribution block for mini-ANL fuses with one (1) 4 or 1/0 AWG set-screw input and four (4) 4/8 AWG set-screw outputs
Plastic cover (attached)
3 Rubber grommets and sleeves (pre-installed)
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
29.75 |
|
|
VFDB2 MANL 2 Position Distribution Block with Cover
This compact distribution block from T-Spec will handle the high-current power distribution for your single source to two (2) smaller gauge power wires, ensuring that your wiring's connected securely, looking neat, and safely fused. T-spec's Universal Screw Design for securing the wires and mini ANL fuses to the block works with a variety of tools. Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover keeps the fuses and connections clean.
Fuses sold separately.
Features:
One (1) 1/0 to 4 AWG in to two (2) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate Lock technology
In the Box:
One distribution block for mini-ANL fuses with one (1) 4 or 1/0 AWG set-screw input and two (2) 4/8 AWG set-screw outputs
Plastic cover (attached)
3 Rubber grommets and sleeves (pre-installed)
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
23.03 |
|
|
Bosworth 1.5 Aluminum Outlet Aluminum Fitting 1.5Npt
|
78.98 |
|
|
Marine Amp Wiring Kit
In order to deliver the highest quality in sound and performance, Roswell has developed its own wiring accessories to join all of your Roswell Marine audio products together. Everything you need to install and connect two amplifiers (except the amplifiers themselves) is included in this package.
Includes:
(1) power fused distribution block: (1) 1/0 AWG/4 AWG in, (2) 4 AWG/8 AWG out
15 ft. 4GA. satin charcoal ground wire – 105°C rated, tinned OFC full-spec copper
(1) power ground distribution block: (1) 1/0 AWG/4 AWG in, (2) 4 AWG/8 AWG out
15 ft. 4GA. satin blue power wire – 105°C rated, tinned OFC full-spec copper
(1) inline fuse holder - 1/0 AWG in/out with 4 AWG reducers
10 ft. 18GA. frosted blue remote wire – tinned OFC full-spec copper
(1) 100 Amp mini ANL fuse
(2) 2-meter smoked jacket, quad shielded RCA cables
(2) 60 Amp mini ANL fuses
(2) RCA Y-Adapter (1F to 2M)
(1) 50 amp mini ANL fuse
(2) RCA Y-Adapter (1M to 2F)
(1) 80 amp ANL fuse
(12) 4" black cable ties
(1) 100 amp ANL fuse
(6) stainless steel 3.9 x 16mm screws
(1) 150 amp ANL fuse
(2) M8 washers (ID: 8.4mm, OD: 16mm)
(1) 4GA. brass terminal ring with black boot & M10 bolt
(1) 4GA. brass terminal ring with red boot & M10 bolt
*Does not include amplifier-to-speaker wiring
|
180.00 |
|
|
VPNB4 MANL 4 Position All-In-One Distribution Block with Cover
T-Spec designed VPNB4 distribution block to handle the high-current power and ground distribution for four (4) power sources, and protect them each with a mini-ANL fuse. This hefty little block distributes power from one (1) 1/0-gauge positive power cable to four (4) 4 to 8 gauge power leads, each routed through a mini-ANL fuse.
Then, the same block receives the amps' two ground wires and combines them for a single 1/0 to 4 gauge ground cable.
Fuses sold separately.
Features:
(2 positive) 1/0 to 4 AWG in to (4 positives) 4/8 AWG out
(1 negative) 1/0 to 4 AWG in to (4 negatives) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate Lock technology
In the Box:
Distribution block for both power and ground
Plastic cover (attached)
3 Rubber grommets and sleeves on power inputs (installed)
2 Rubber grommets and sleeves on power outputs (installed)
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
37.12 |
|
|
VPNB2 MANL 2 Position All-In-One Distribution Block with Cover
T-Spec designed VPNB2 distribution block to handle the high-current power and ground distribution for two (2) power sources, and protect them each with a mini-ANL fuse. This hefty little block distributes power from one (1) 1/0-gauge positive power cable to two (2) 4- to 8-gauge power leads, each routed through a mini-ANL fuse.
Then, the same block receives the amps' two ground wires and combines them for a single 1/0-gauge ground cable.
Fuses sold separately.
Features:
(2 positive) 1/0 to 4 AWG in to (2 positives) 4/8 AWG out
(1 negative) 1/0 to 4 AWG in to (2 negatives) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate Lock technology
In the Box:
Distribution block for both power and ground
Plastic cover (attached)
2 Rubber grommets and sleeves on power inputs (installed)
2 Rubber grommets and sleeves on power outputs (installed)
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
21.53 |
|
|
VDB2 2-Position Distribution Block with Cover
T-Spec designed their VDB2 distribution block to handle the high-current power distribution for two (2) power sources while keeping your wiring connected securely and looking neat. You can also use this hefty little block to combine the ground wires of two (2) sources to a single grounding point. Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover protects your connections from the weather.
Features:
One (1) 1/0 to 4 AWG into two (2) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate lock technology
In the Box:
Distribution block with one (1) 1/0 set-screw input and two (2) 4 or 8 AWG set-screw outputs
Plastic cover (attached)
3 Rubber grommets and sleeves (pre-installed on input and outputs)
Two 1/2" screws
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
20.84 |
|
|
VDB4 4-Position Distribution Block with Cover
T-Spec designed their VDB4 distribution block to handle the high-current power distribution for four (4) power sources while keeping your wiring connected securely and looking neat. You can also use this hefty little block to combine the ground wires of four (4) sources to a single grounding point. Solid black nickel-plated brass construction ensures reliable power flow, and an impact-resistant polycarbonate cover protects your connections from the weather.
Features:
One (1) 1/0 to 4 AWG into four (4) 4/8 AWG out
TPE wrapped soft touch
Dual sizes gasket set
Water-resistant
Solid brass construction
Black nickel finish
T20 Torx® screws
Gate lock technology
In the Box:
Distribution block with one (1) 1/0 set-screw input and four (4) 4 or 8 AWG set-screw outputs
Plastic cover (attached)
3 Rubber grommets and sleeves (pre-installed on input and outputs)
Two 1/2" screws
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
21.53 |
|
|
Series 75 Core Block™ - Single
Core Blocks™ are a true all round solution. A tuned 2-stage bearing system provides excellent performance across the full working load range with an integrated thrust bearing feature and the resilience to handle high dynamic or static loads. Acetal sheave, alloy cheeks and stainless fixings complete the durable package. For reliability and a long service life, these blocks are the right choice for sheets, halyards and control line applications for cruising and racing.
Universal Bearing
Dynamic and high static load performance
The Ronstan Universal Bearing incorporates our proven 2-stage bearing system
Stage 1 - Under moderate loads, Acetal ball bearings ensure minimum friction.
Stage 2 - Under heavy loads, where deformation of ball bearings alone would result in increased friction, a sliding Acetal bearing on a polished stainless steel race takes over, maintaining low friction performance.
Additionally the ball bearings are configured to act as a thrust bearing between the sheave and cheeks, preventing the sheave from rubbing on the cheeks and causing friction when the line lead in and out of the block isn't perfect. Particularly important for cheek blocks.
Alloy Cheek Plates
Block cheeks are manufactured from the highest quality alloy for maximum strength. Material optimisation and the cut-away design minimises weight and allows easy fresh water rinsing of salt and debris from the bearings. Cheek design has been further styled with flaring at the block throat and reduced gap between the cheek and sheave, minimising rope wear.
Universal head
The head assembly incorporates a brass bearing washer to provide smooth 360™ rotation of the post and shackle. A set screw arrangement allows the head to be locked at 0™ or 90™.
Shackles are high quality forged grade 316 stainless steel.
Features:
Class leading performance and sleek, contemporary styling
Excellent dynamic and high static load performance
Less than half the friction of the nearest competitor
Universal head with full 3-axis articulation
Head posts can be locked at 0 or 90 degrees, by using a 2.5mm Hex/Allen Key
Central hub hole can be used as a becket take-off or tie-up point
Applications:
Ideal for mainsheet, halyard and spinnaker sheet applications on boats to 14M (46')
Various control line applications on larger yachts
Materials:
Sheave: U.V. stabilized Acetal
Cheek body: Aluminium Alloy
Ball Bearings: High compression strength carbon black Acetal
Shackle, head post & hub: Grade 316 stainless steel
Specifications:
Sheave Ø: 75mm(3")
Max. Rope Ø: 14mm(9/16")
Pin Ø: 8mm(5/16")
M.W.L.: 1,500kg(3,300lbs)
B. L.: 3,000kg(6,600lbs)
Weight: 354g(12.5oz)
|
102.67 |
|