Outdoor Antenna for GX LTE 4G-A This antenna is optimized for 4G frequency bands and, as such, will have slightly better reception on the 4G network. It can be used with the GX LTE 4G for 2G, 3G, and 4G bands. If the 2G/3G variant does not provide sufficient signal quality in an installation, the solution is to contact a local GSM antenna provider. All the necessary information, including a link to the cellular modem (Simcom) used, can be found in this manual. Specifications: Mounting Option: Screw mount Cable Type: RG-316 Cable Length: 3.0 m Connector: SMA male straight Frequencies: 800/900/1800/1900/2100 MHz Signal Gain: 3 dBi Please contact your dealer for any returns, repairs or support issues related to this product.

GX LTE 4G-A Cellular Modem for GX Devices - North America Only The GX LTE 4G is an accessory for GX devices. It is a cellular modem that supports 2G, 3G, and 4G technologies. It provides mobile internet for the system and a connection to the Victron Remote Management (VRM) portal. Built-in GPS Receiver The GX LTE 4G includes a built-in GPS receiver. When the optional active GPS antenna is installed, the system can be tracked as well as geo-fenced on the VRM Portal. The required accessory part number is GSM900200100 - Active GPS Antenna for GX GSM. GX Compatibility The GX LTE 4G can be used with any of the GX devices and requires Venus OS v2.60 or newer to be installed on the GX device. SIM Card It requires a SIM card in the Mini-SIM format. When to Use a Mobile Router Instead The GX LTE 4G provides an internet connection for the GX device only. There is no option to share the internet with laptops, phones, or other devices. For installations where more devices need internet, such as a yacht or RV, consider installing a mobile router instead. Antennas and Accessories A small indoor LTE antenna is included. Optionally, Victron sells an outdoor LTE antenna, which increases the range. Part number GSM900100400 - Outdoor 4G GSM Antenna. Specifications: Region: For North America Used Module: SIMCom, SIM7600A Supported LTE Bands: 2, 4, 12 Supply Voltage Range: 8 - 70VDC Power Draw: 2.5W while 2G/3G/4G data transfer / <1.0W in idle mode / +0.4W if GPS is enabled Operating Temperature Range: -40 +50°C (-40 - 120°F) Power Cable (Included): 1.4m cable with inline fuse holder, terminal block, and 10mm ring terminals Inline Fuse (included): T3.15A250V Communication Specifications: USB Communication Port: Fixed 1.0m cable with USB-A connector (connects to the GX device) LTE Antenna Connector: Type SMA Female (optional 4G outdoor antenna GSM900100400) GPS Antenna Connector: Type SMA Female (optional GPS antenna GSM900200100) GNSS: GPS/Beidou/GLONASS/GALILEO/QZSS SIM Card: Regular Mini SIM (supports both 1.8V and 3V) Data Transmission (max. Download/Upload) LTE Cat-1: 10 Mbps / 5 Mbps Data Transmission (max. Download/Upload) 3G (HSPA+): 42 Mbps / 5.76 Mbps Data Transmission (max. Download/Upload) 2G (EDGE): 236.8 Kbps / 236.8 Kbps Data Transmission (max. Download/Upload) 2G (GPRS): 85.6 Kbps / 85.6 Kbps Status Indicator: Blue LED Installation & Dimensions: Dimensions (l x w x h): 106 × 42.5 × 22mm Weight: 0.08kg (0.177lbs) Wire Gauge (power cable): 0.5..1.5mm2 / AWG 28..16 or use supplied power cable Recommended Fuse Size: 500mA @ 12V / 250mA @ 24V / 100mA @ 48V or use supplied inline fuse In the Box: GX LTE 4G (with integrated USB cable) GSM 2G/3G/4G mini-rod antenna (for indoor use) DC power cable (with inline fuse and terminal block) Standrads: Safety: EN 60335-1 / EN 60335-2-29 / EN 62368-1 Emission / Immunity: ECE R10-5 QM: EN 9001:2015 Please contact your dealer for any returns, repairs or support issues related to this product.

Active GPS Antenna for GX LTE Modem This antenna is for the GX LTE Modem. Specifications: Mounting Option: Magnet Cable Type: RG-74 Cable Length: 3.0 m Connector: SMA male straight Frequencies: 1575.42 MHz Signal Gain: 50 Ω Please contact your dealer for any returns, repairs or support issues related to this product.

Standard Antenna f/M88 & F50 150-174MHz Red Ring

Standard Antenna Soft, flexible replacement antenna f/M92D

Standard Antenna Standard Replacement Antenna f/GM1600

5G Xtream System with 3 Antennas & 7M Cable For boat owners looking for ultra-fast internet on board, the new 5G Xtream from Digital Yacht offers 4G and 5G connectivity as well as integration with Starlink satellite systems for the best and most affordable blended internet afloat. The 5G Xtream can support 5G (shoreside) connection speeds up to 3.1GB/s but also integrates a 4G Cat 20 modem, which offers connectivity up to about 25NM from shore at speeds of up to 2GB/s. The system uses three external antennas with dual high-gain vertical antennas and a separate compact dome for the higher 5G frequencies. This MIMO technology and, critically, separate antennas give optimum performance. There’s support for dual SIMs with auto (failover) or manual switching between operators. The 5G Xtream features dual-band (2.4 and 5GHz) wireless connections, so users on board simply search for the secure wifi point and connect. There are also 4 LAN ports (10/100/1000 MB) for wired devices like smart TVs and a WAN port that is optimized for Starlink satellite connectivity, allowing the 5GX to act as a sophisticated and fast router for all on-board internet communications. The Wi-Fi router can also be configured to access marina wifi hotspots as an additional method of internet access. This also supports the very latest 5GHz marina wifi services, and there's also a high-gain external wifi antenna available as an accessory. For advanced users, the 5G Xtream allows for user management, VPNs, blacklists, and IOT applications. NMEA 0183/2000 data can also be connected using Digital Yacht’s LANLink devices. The integrated GPS allows for SMS reporting of boat position or even a geofence/drift setting when the boat is at anchor or in port. The Digital Yacht 5G Xtream is supplied as a complete solution with antennas, mounts, and cabling – all that’s additionally required is a cellular SIM. Configuration Configuration is very simple. Just insert the SIM cards. The 5G Xtream has two standard SIM slots, and it is possible to fit two SIMs from two different network operators. By default, the 5G Xtream will query the SIM that is installed and automatically select the APN settings from its internal database. However, it is very important that users “lockdown” their wireless network with their network name (SSID) and wireless password. This task only takes a couple of minutes and is done via the 5G Xtream web interface. User Interface Accessing 5G Xtream functionality is done via an easy web interface. Any locally connected device can simply enter the IP address into the password-protected interface to set up functions, view traffic and logs, and configure wifi. Once set up, there should be no requirement to log in other than for diagnostics and configuration. Users simply access the internet through the wifi connection, just as they would in the home or office. Features: Ultra-fast 5G internet afloat solution with speeds up to 3.1GBs plus also integrates the latest 4G Cat 20 LTE MIMO technology with a range up to 25NM offshore (network dependent) and 4G connection speeds up to 2GBs Dual SIM slots with auto-failover or manual selection Two external, high-gain, wide-bandwidth antennas plus a compact high-gain dome antenna for higher 5G frequencies Dual-band integrated wifi router (2.4 & 5 GHz)—independently configurable Built-in GPS with an external patch antenna for IOT and tracking/anchor alarm applications 4 x LAN ports 1 x WAN port for additional internet connectivity, optimized for Starlink satellite systems Digital input/output connectivity for IoT/control applications SMS capability 12/24v Weight: 3800 g Dimensions: 180 x 125 x 55 mm operation Specifications: Operating Temperature: -40 to +75 degrees C Dimensions: 180 x 125 x 55mm (excluding antennas) Weight: 3,8 kg Protection: IPX4 Technology: 5G Sub-6Ghz SA/NSA. Up to 2.1/3.3Gbps downlink (4×4 MIMO); 4G (LTE) CAT 20 up to 2GB/s 5G/LTE: 5G Sub-6Ghz SA/NSA. Up to 2.1/3.3Gbps downlink (4×4 MIMO); 4G (LTE) CAT 20 up to 2GB/s 3G/4G Fallback (Support bands): 5G (NSA): n1, n3, n5, n7, n8, n20, n28, n38, n40, n41, n77; 5G (SA): n1, n3, n5, n7, n8, n20, n28, n38, n40, n41, n77, n78; 4G (LTE-FDD): B1, B3, B5, B7, B8, B20, B28, B32; 4G (LTE-TDD): B38, B40, B41, B42, B43 4G & 5G Antennas: Dual Wi-Fi band independent 2.4 & 5 GHz (maximum 150 connections); dual 48cm external wideband high gain MIMO supplied with 7-meter cables and mounting bases. (10 & 20m options available) PLUS additional 100mm dome antenna for 4 x 4 MIMO operation and optimized for 5G (7m cable only) Interfaces: 4 x LAN 10/100 Ethernet Port; 1 x WAN 10/100 Ethernet Port ; WiFi; 802.11 b/g/n/ac What’s in the Box? 1 x 5G Xtream Modem Unit 1 x DC Power/IO cable 2 x External antennas 2 x E179F antenna bases 2 x 7m LMR200 antenna cables (N male to N male) 1 x 5G dual element dome antenna with pole/1” adaptor mount and integrated 7m cables 2 x Internal wifi antennas 1 x Internal GPS antenna Options (sold separately): 1” antenna adaptors and range of mounts 10 & 20m LMR400 antenna cable packs for 4G antennas AC 110/220v power adaptor 4GXWL hi power external wifi option LANLink NMEA 0183/2000 interface

4G/5G LTE Omni-Directional MIMO Antenna - White Overall data throughput is increased by using Multiple Input Multiple Output (MIMO) devices. Digital Antenna's 1742-MIMO antenna encompasses two separate antennas in one radome allowing devices requiring multiple RF connections to use fewer antennas.  Designed with vertical polarization, the Digital Antenna 1742-MIMO antenna provides the strongest 4G/5G/LTE signals for enhanced data speeds in poor cellular and WiFi signal areas.  Unsurpassed performance from 4-9dBi gain omnidirectional, dual vertical-polarized antennas covering 695-3000 MHz enclosed in a rugged UV stable, marine grade fiberglass housing with corrosion-resistant stainless steel hardware. Features: Vertically polarized, dual-integrated antennas 9dBi peak gain Enhanced data speeds Rugged UV stable polyurethane finish Foam-filled weatherproof housing Corrosion-resistant stainless steel components VSWR <1.5:1 in 4G & 5G bands Heavy-duty pole mount included Dual female N-type connectors RoHS Compliant

4G Connect Pro 2G/3G/4G Dual Antenna Digital Yacht's 4G Connect is a 2G/3G/4G (LTE) internet access solution for use afloat.  It utilizes the latest MIMO technology with dual antennas for fast, long-range access and incorporates a full-function wifi router so multiple devices can connect wirelessly.  There is also a wired LAN port and WAN port – for connection to high-power wifi devices or satellite modems. The Pro model ships with two external hi-gain antennas for exceptional long-range performance and is the recommended solution for use afloat. 4G Connect has an easy-to-use interface. It is SIM unlocked so users are free to use any cellular provider they choose. Operation is simple – turn on, connect to the password-protected wifi hotspot that 4G Connect creates and your device is online.  Digital Yacht’s WL510 high-power wifi solution can also be connected to the WAN port for a choice between hotspot wifi and 4G connectivity.  iKommunicate can also connect to the LAN port providing boat NMEA data on the wifi network for use with navigation apps. Features: Hi-performance 4G/LTE modem for exceptional speed and range with fall back to 2G/3G SIM unlocked for any network provider Supplied with 2 x high performance external 48cm antennas for optimum speed and range 7m low loss LMR 200 cable kit included Supplied with deck base for antennas (as shown) LTE Class 3 modem offers long range and up to 70Mbps speeds The recommended solution for offshore use and non-GRP vessels Wifi interface for tablets and phones Ethernet LAN port for connection to iKommunicate navigation interface – allows boat NMEA 0183/2000 data to be available on the wifi network – ideal for smartphone and tablet navigation Ethernet WAN port can connect to satellite or WL510 high power wifi system for combination LTE/WiFi hotspot solution 12V DC operation with <5W power consumption Optional 1” base adaptor available for antennas Optional 10 & 20m LMR400 assemblies Supplied With: 7M Cable Kit

1664-PW Wideband 4G/5G/LTE/WiFi Omni with F114 & DM194 Deck Mount Digital Antenna's omni-directional, bullet-shaped antenna with stainless steel base provides excellent performance from 695-3000 MHz and is ideal for mobile or fixed locations. High gain 9dBi bullet antenna designed and manufactured in the USA by Digital Antenna, greatly improves signal strength providing a maximum signal range. The new design includes a rugged stainless steel base. For use with any device that connects to the cellular network or WiFi such as routers, modems, and amplified signal boosters and gateways. Available in several mounting options for use on boats, buildings, utilities, M2M, and more.marine environment. Features: Maximum power for 4G, 5G, WiFi signals 9dBi omni-directional gain Rugged UV stable polyurethane finish Foam filled to withstand extreme vibrations 316 stainless steel base Includes deck mount Weatherproof N female connector 5-year warranty

1685-PW Wideband 4G/5G/LTE/WiFi 9dBi with Antenna Deck Mount Digital Antenna's omni-directional antenna with stainless steel base provides excellent performance from 600-3000 MHz and is ideal for mobile or fixed locations.  9dBi antenna designed and low profile manufactured in the USA by Digital Antenna, greatly improves signal strength providing a maximum signal range. For Use with any device that connects to the cellular network or WiFi such as routers, modems, amplified signal boosters & gateways. Available in several mounting options for use on boats, buildings, utilities, M2M, and more marine environments. Features: Maximum power for 4G, 5G, WiFi signals 9dBi omni-directional gain Rugged UV stable polyurethane finish Foam filled to withstand extreme vibrations 316 stainless steel base Includes Deck Mount Weatherproof N female connector 5-year warranty

Smart Buck-Boost 50A (700W) DC-DC Charger - Non-Isolated The Smart BuckBoost DC-DC Charger can be used as a battery charger or as a power supply with a wide input and output voltage range. In charger mode, the four-stage charge algorithm will increase battery life by properly charging the battery. Especially in the case of vehicles with a Euro 5 or 6 smart alternator, which often supplies too low charging voltage even with the engine running or in the event of a voltage drop over long cables, controlled charging is crucial. Controlled charging also protects the alternator in lithium systems from overloading, as the low impedance of lithium batteries results in a high alternator current. In power supply mode, the output voltage remains stable regardless of the applied load or fluctuating input voltage (within the specified range). The output voltage is fully adjustable and remains independent of the input voltage, thanks to the automatic buck-boost control. This control also guarantees that the current will never exceed the set value, even when the input voltage is higher than the output voltage. The Smart BuckBoost can be set to only supply power when the engine is running. This is possible thanks to the integrated engine shutdown detection. This eliminates the need to adjust in-vehicle wiring or add an engine detection sensor to determine if charging can start. It also prevents the voltage on board the vehicle from getting too low. In addition to this detection, the Smart BuckBoost can also be forced on via the remote on/off port. The Smart BuckBoost is fully programmed and monitored using the VictronConnect App. This also includes remote access via VictronConnect-Remote (VC-R) when connected to a GX device (requires a GX device connection to the VRM Portal) via the integrated VE.Direct port, monitoring via the GX Remote Console or from a PC, Apple computer with macOS, or Android device in conjunction with a VE.Direct to USB interface and VictronConnect. Discover all setting and monitoring options in the Setup & monitoring with VictronConnect [15] chapter and the VictronConnect manual. In the Box Smart Buck-Boost 50A (700W) non-isolated DC-DC Charger 12/12-50 with terminal block for remote on/off connection   Features Smart Alternator Compatibility It is common for vehicle manufacturers to install "smart" ECU (Engine Control Unit) controlled alternators to increase fuel efficiency and reduce emissions. Smart alternators provide variable output voltage and shut down when not needed. The Smart BuckBoost has an integrated mechanism that detects whether the engine is running (engine shutdown detection), so the charger is only activated when the alternator is supplying power. This ensures that the charger only draws power when the alternator supplies power. Separation of the Starter Battery and the Service Battery The Smart BuckBoost separates the starter battery from the service battery. Comprehensive Electronic Protection The charger is protected against overtemperature (bottom plate >90 °C) by reducing the output power when the maximum product temperature is reached. Protected against overload Protected against short circuit Protected against excessive temperatures Adaptive charging in four stages The Smart BuckBoost is configured by default for a three-stage charging process. Bulk — Absorption — Float — Storage Bulk - During this phase, the Smart BuckBoost supplies as much charging current as possible to quickly charge the batteries. Absorption - When the battery voltage reaches the absorption voltage setting, the charger switches to constant voltage aka absorption mode. For lead-acid batteries, it is important that the absorption time is kept short during superficial discharges to avoid overcharging the battery. After a deep discharge, the absorption time is automatically increased to ensure that the battery is fully charged again. For lithium batteries, the absorption time is fixed, 2 hours by default. Fixed or adjustable modes can be selected via the battery settings. Float - During this phase, the battery is charged with a trickle charge voltage to keep it in a fully charged state. When the battery voltage drops far below this level, for example, due to a high load for at least 1 minute, a new charge cycle is activated. Storage - The battery voltage is maintained at the configured storage voltage, which is slightly reduced comp Flexible Charge Algorithm The Smart BuckBoost has fully programmable charge algorithms and eight pre-programmed battery settings. Configurable with VictronConnect. Adaptive Absorption Time In adaptive absorption time mode, the correct absorption time is calculated automatically. Configurable with VictronConnect. Repeated Absorption To refresh the battery and prevent slow self-discharge while in the storage stage over an extended period, a 1-hour absorption charge will automatically occur every 7 days (or as configured). Temperature-Compensated Charging The optimum charge voltage of a lead-acid battery is inversely proportional to temperature. The Smart BuckBoost DC-DC Charger measures the ambient temperature at the start of the charging phase and compensates for the temperature during charging. The temperature is measured again when the battery charger is in low current mode during absorption or storage. Special settings for a cold or warm environment are therefore not required. Adjustable Charge Current The charge current is adjustable with a minimum step size of 0.1A. Configurable with VictronConnect. Low-Temperature Shutdown Prevents damage to lithium batteries by turning off the charger at low temperatures. Configurable with VictronConnect. Input Voltage Lock-Out Shut down the charger when the input voltage falls below the lock-out value and restart when the input voltage rises above the restart value. Configurable with VictronConnect. Remote On/Off The inverter can be switched on and off remotely via the remote on/off connector or the VictronConnect App. Typical applications include a wired switch or a lithium battery with a Battery Management System (BMS) that has an ATC (allowed to charge) output. VE.Direct Monitor and control (on/off) the Smart BuckBoost via a wired connection from a GX device such as the Cerbo GX, Ekrano GX, or use a PC, Apple computer (requires macOS), or Android device in conjunction with VictronConnect via a wired VE.Direct connection. Configuration and Monitoring via VictronConnect App and Bluetooth Built-in Bluetooth Smart: the wireless solution to change settings, monitor activities, and update software using Apple and Android smartphones, tablets, or other devices. Various parameters can be adjusted and monitored with the VictronConnect App. This also includes Instant Readout, which displays the most important data of the Smart BuckBoost (and other smart products) on the Device list page without the need to connect to the product. This includes visual notifications of warnings, alarms, and errors that enable diagnostics at a glance.  VictronConnect is available for Android, iOS, Windows, and macOS. See the VictronConnect manual to get the most out of the VictronConnect app when connected to a Victron smart product. Waterproof The Smart BuckBoost complies with an ingress protection rating of IP65; this means the product is dust-tight and protected against heavy rain. Silent The heat is dissipated through natural convection, eliminating the need for a noisy cooling fan.  Specifications: Input Voltage Range: 9-17V Output Voltage Adjust Range: 10-17V Output Voltage Tolerance: +/- 0.25% (max) Output Voltage Noise: 10mV rms Input and Output Current Setting Range: 1 - 50A Maximum Constant Short-Circuit Current: 50A Continuous Output Power up to 40 °C: 700W Maximum Efficiency: 98.5% No-Load Current Consumption: < 100mA Standby Current Consumption: < 1.5mA Communication Ports Specifications: Bluetooth Smart: Yes VE.Direct: Yes Other Specifications: Operating Temperature Range: -20 to +60 °C (derating 1.5% per °C above 40 °C) Protection Category: IP65 DC Connection: Screw terminals Maximum Cable Cross Section: 25mm² AWG4 Weight: 0.330kg (0.73 lb) Dimensions h x w x d: 137.3 x 123.1 x 40mm (5.4 x 4.85 x 1.6 inch) Standards Safety: IEC 62477-1 Emission: IEC 61000-6-3, EN 55014-1 Immunity: IEC 61000-6-2, IEC 61000-6-1, EN 55014-2 Automotive Directive: ECE R10-5 Please contact your dealer for any returns, repairs or support issues related to this product.

Cerbo-S GX Basic Version - Limited Inputs No BMS Can Port The communication center allows you to always have perfect control over your system from wherever you are and maximizes its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, an MFD, or our VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX range combines all the best of connectivity, redefining smart power solutions in every way. The Cerbo-S GX maximizes the performance of your system's components in real time and keeps them in perfect tune. With 3 VE.Direct ports, 3 USB ports, 4 digital inputs, and 2 relays allow you to expand control to a new level. Maximizing systems performance was never this easy. Features: Cerbo GX: Communication center- This communication center allows you to always have perfect control over your system from wherever you are and to maximize its performance. Simply access your system via our Victron Remote Management (VRM) portal, or access it directly, using the optional GX Touch screen, a Multi-Functional Display (MFD), or our VictronConnect app thanks to its Bluetooth capability. GX Touch: Display accessory (sold separately)- The GX Touch 50 and GX Touch 70 are display accessories for the Cerbo GX. The five-inch and seven-inch touchscreen displays give an instant overview of your system and allow you to adjust settings. Simply connect the display to the Cerbo GX with just one cable. Both GX Touch displays have a waterproof design, and a top-mountable setup, and are simple to install. Remote Console on VRM- Monitor, control and configure the Cerbo GX remotely, over the internet. Just like if you were standing in front of the device, using the Remote Console. The same functionality is also available on the local network LAN or using the WiFi Access Point of the Cerbo GX. Perfect monitoring & control- Instantly monitor the battery state of charge, power consumption, power harvest from PV, generator, and mains, or check tank levels and temperature measurements. Easily control the shore power input current limit, (auto) start/stop generator(s) or change any setting to optimise the system. Follow up on alerts, perform diagnostic checks and resolve complications remotely. Simple mounting and configuration- The Cerbo GX is easily mountable and can also be mounted on a DIN-Rail using the DIN35 adapter small, (not included). Its separate touchscreen can be bolted on a dashboard, eliminating the need to create perfect cutouts (like with the Color Control GX). Connection is easy via just one cable, taking away the hassle of having to bring many wires to the dashboard. The Bluetooth feature enables a quick connection and configuration via our VictronConnect app. Please contact your dealer for any returns, repairs or support issues related to this product.

UFO XL High Gain 15" 34dB Marine TV Antenna The Majestic UFO XL is a larger version of the current model TV Antennas. Developed with a larger and more powerful amplifier to be able to boost the smallest signal, the Majestic UFO XL is designed for Offshore and Outback performance. The Majestic engineering team understands the limitations of both the Marine and Outback environments and developed the Majestic UFO XL specifically for boats, caravans, motorhomes, buses, trucks, and RVs. Using the latest in high-tech engineering the Majestic development team was able to use the larger size and improved amplifier to create one of the most powerful TV antennas in the Marine and RV industry. You won’t find a company that develops its own TV antenna and TV which are perfectly tuned to give you the performance needed when you are in fringe areas such as boating or in the RV industry. Features: Size: The Majestic UFO XL is 38cm (15") wide and is packed with the latest in technology RF Amplifier to give you the ultimate in offshore or outback performance. It is slightly larger than the UFO X, so is it capable of picking up small signals in a larger surface area and combined with the more powerful RF amplifier ensures excellent reception.   Gain: Firstly the main engineering improvement is the boosting of the amplifier of the UFO XL which is at 34dB versus the UFOX at 30 dB. The UFO XL has a 34dB High Gain Amplifier built into the Antenna which is a 130% increase in signal performance on the UFOX. (For every 3dB Gain the signal level double). This gives you a huge advantage over other TV antennas because now you have a very strong signal in the antenna that has not had any interference being induced when it received the signal, and with a very strong signal being sent down the cable, the electrical interference is insignificant compared to the strong signal. Once the signal is sent down to the junction we do not need to do any filtering or cleaning to give you excellent digital reception.  Vertical and Horizontal: The UFO XL has had a vertical and horizontal plane incorporated to give you the performance needed in both Vertical and Horizontal locations. This feature is rarely found in TV Antennas as most are either designed to work in a Vertical or Horizontal application. For those that are looking for a TV antenna that can perform worldwide covering both vertical and horizontal, digital and analog signals then the Majestic UFO XL Marine and RV TV Antenna is the ultimate choice.  SNR: Signal to Noise Ratio. This is one of the most important factors of a TV Antenna which has an amplifier. The lower the signal to noise ratio the better the amplifier performs. Basically we are comparing Signal vs Noise. The more signal we have and the less noise we have the better the amplifier works. The UFO XL uses state-of-the-art-technology to produce a very low a signal to noise ratio of 3dB which is extremely low compared to most other brands. This means that more signal is amplified and less noise is amplified, which in turn means better performance. This also significantly improves distance performance, as the further you get the signal is weaker, and the noise of electrical interference, other noise still remains high, so the UFO XL Amplifier is able to clean the signal and give you exceptional performance.  Ground Independent: The UFO XL is also designed to be ground independent (does not need a ground plane or be grounded) to amplify the TV signal. This design is very specific as most installations do not allow for a proper RF Ground, which is totally different from an electrical ground. This is another brilliant engineering design by Majestic to make this antenna perfect for boats or any non-metal roof installation.  Voltage Range – Most Antenna brands claim they are 12 Volt, and technically yes they work on 12 Volts. However, the issue is the level of tolerance that most of these Antenna have, most 12 Volt TV antenna have a limited tolerance, generally between 11V and 14V. This can cause many people problems especially when they have long cable runs, or the battery voltage drops a little (especially late at night), or even if they have a poor power connection. The Majestic UFO XL TV Antenna is designed to work from 9V through to 27V DC, therefore ensuring you will not have any power issues. The TV Antenna is not designed to work on a 24V system if the charging goes above 28V DC.  TV Reception - One important factor in being able to receive TV signal is the signal level. The Majestic UFO XL TV antenna which has the highest gain at 34dB for its 15" size, you can be assured that if there is any chance of signal reception, you will be the one that can get it with the Majestic UFO XL. The Majestic engineering team understands the limitations of both the Marine and Outback environments and developed the Majestic UFO XL specifically for boats, caravans, motorhomes, buses, trucks and RV's.  UHF/VHF/FM/DAB: The UFO XL is capable of receiving signal on different frequencies. Throughout various countries there are UHF and VHF signals for Digital and analog TV, the UFO XL can pick them up and integrate the process in the antenna and amplify them and send a nice clean signal down the cable for your TV. But more importantly the UFO XL can pick up FM and DAB signals and boost this performance. The UFO XL Junction box has Two Outputs and you can use one of them for the FM Signal to give you improved radio performance. The two outputs from the junction box incorporate UHF/VHF/FM/DAB so it does not matter which port you use for the different devices.  Warranty: Majestic products are designed and developed in Australia and exported globally, with over 15 years experience Majestic stands by the quality of our products by providing a 3 year worldwide warranty. Our engineering design team has paid attention to all the important details to ensure that when you purchase a product of this quality and caliber that you can enjoy many years of reliable performance in the toughest conditions where domestic brands will not survive. Upgrading: For those wishing to upgrade, the Junctions boxes are fully interchangeable between the Majestic UFO and the Majestic UFO X so therefore you do not need to change the Junction if you upgrade to the UFO XL higher performance Antenna. Performance: The UFO XL has been re-engineered using the latest in state-of-the-art technology to allow it significantly outperform the previous UFOX Model. So if you are looking for an antenna to give you better performance in fringe areas then the UFO XL will give you the Extreme performance you are looking for.

Cerbo GX This communication-center allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, a MFD or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way. Perfect Monitoring & Control Instantly monitor the battery state of charge, power consumption, power harvest from PV, generator, and mains, or check tank levels and temperature measurements. Easily control the shore power input current limit, (auto)start/stop generator(s) or change any setting to optimise the system. Follow up on alerts, perform diagnostic checks and resolve challenges remotely. The Cerbo GX turns any power challenge into an effortless experience. Maximize Your System Performance The Cerbo GX maximises the performance of your systems components in real-time and keeps them in perfect tune. With its Dual Core Processor and the addition of an extra CAN-bus port you can now support even bigger systems; closely follow managed (lithium) batteries while the second port can support up to 25 simultaneously connected VE.Can solar chargers. The new NMEA 2000-out support has the GX easily integrated into any boats network. Four tank- and four temperature ports as well as 3 VE.Direct ports, 3 USB ports, 4 digital inputs and 2 relays allow you to expand control to a new level. Maximising systems performance was never this easy.  Expand Your View The (optional) GX Touch 50 display allows you to have an instant overview of your system and adjust settings in the blink of an eye. Its super slim 5 inch waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. Simple Mounting & Configuration The Cerbo GX is now optimised to more than meet the standards of installer professionals. The device is easily mountable on a DIN-Rail (with DIN35 adapter small, not included) and its separate touchscreen can now be bolted on top of a dashboard, eliminating the need to create perfect cut-outs (like with the Color Control GX) and is connected through just one cable, taking away the hassle of having to bring many wires to a dashboard. Its new Bluetooth feature enables a quick connection and configuration via our VictronConnect app. Outsmart Any Power Challenge The Cerbo GX serves endless purposes, extending perfect control to the most diverse applications. For solutions including generators, such as Marine, or Backup & Off-grid, it will auto-start/stop your generator, or delays ignition until the end of ‘quiet’ periods. For Energy Storage Systems it keeps backup batteries at 100%, kicks-in during power-cuts and diverts excess (solar) power to self-consumption, saving you money. For RV and Emergency vehicles it keeps vital systems function flawlessly. But that’s just to name a few... Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.