|
As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away.
Outside Storage?
It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.
Rinse/Flush
Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat.
Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring.
Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present.
Salt
Watch out for salt. Buy a good salt remover to minimize corrosion.
Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine.
Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4*
STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel.
Batteries
Remove the batteries from your boat and store in your garage or basement.
Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery.
If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat.
Cleaning
Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint.
Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins.
Cover Up
If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often.
https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html
and
https://www.clrmarine.com/462m4/winterizing.html
Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information.
Fair winds and smooth sailing.
To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/.
_________________________________________________________________________
Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten.
She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com
©Copyright Cheryl Kuba, 3happycampers.com, 2021.
|
|
|
MP Pump 35098 Cent Pump SS 24V
|
406.58 |
|
|
MP Pumps 34296 CENT PUMP SS 24V
|
559.69 |
|
|
MP Pumps 34293 MOTOR 24VDC 3000RPM 316SS
MP Pumps FRX 75
SUCTION AND DISCHARGE 3/4" NPT x 3/4" NPT
APPLICATION Agricultural, Commercial, Industrial, Marine, OEM, Transportation
MATERIALS OF CONSTRUCTION 316 stainless steel
FLOW Up to 28 GPM
HEAD FEET Up to 32'
IMPELLER 316 Stainless steel, Semi-Open (Sintered PM)
DRIVE Close coupled 24V DC
SEAL Standard seal is carbon
|
261.04 |
|
|
MP Pump 28399 Flomax 8 Pump SS: Ped 5.0
MP Pumps Flomax 8, 2" 140 GPM Stainless Steel Pedestal Mount Self Priming Pump 28399
MP Pumps Flomax 8, 2" NPT self priming centrifugal pumps # 28399. Up to 140 GPM, up to 40 PSI (92'), 3450 RPM, all stainless steel construction. Removable flanges and replaceable wear plates protect the housing and eliminate wear. All fasteners are Stainless Steel. Standard mechanical seal have Viton elastomers.
Specifications
Rated Capacity 140 GPM Maximum Discharge Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Construction: Stainless Steel housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss, weight 49 lbs.; 304 stainless steel stub shaft; viton mechanical seal. Motor: None
Pump Capacity - MP Pumps Flomax 8 Self Priming Pumps At 0 Suction Lift, 3600 RPM
HPImp.Capacity At Total Dynamic Head In FeetShut
Off
20'30'40'50'60'70'80'90'
Gallons Per Minute (GPM)
1-1/24.10"105856020----54'
24.62"12711090704515--74'
35.0"1501401201008060401596'
|
2854.01 |
|
|
March 809 BR HS Mag-Drive Centrifugal Pump Bronze 24V Pump
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze 24VDC High Speed 7.5GPM 1/2"MPT Ports
|
463.13 |
|
|
Oberdorfer 830B-N24Vdc Cent Pump Brz 1Hp 24Vdc
|
3387.07 |
|
|
MP Pumps FloMax FMX 100 1" x 1" Close Coupled 3/4HP Motor Single Phase 39529
The patented 1” x 1” FMX100 self-priming centrifugal pump is constructed of 316 SS for superior corrosion resistance and compatibility with most fluid types. A type 6A carbon / ceramic / viton mechanical seal is standard. With a maximum flow of over 55 GPM and pressure capabilities of nearly 60 feet, this rugged self-priming pump is capable of 17 feet suction lift when operating at 3450 RPM.
The FMX 100 has numerous applications in industries such as: construction, petroleum, diesel exhaust fluid, marine and marine air conditioning, agriculture for biocides and liquid fertilizers, and numerous industrial applications such as brine and calcium chloride.
Discharge 1"
Suction 1"
Materials of Construction 316 stainless steel
Flow Up to 55 GPM
Head Feet 60'
Impeller 4.0"
Drive Options Close Coupled 1 HP TEFC IEC80B34 Motor
Close coupled 3/4HP TEFC IEC80B34 Motor
Engine Mount for 3/4" Shaft
Pedestal Mount 3/4" Shaft
Seal Type 6A carbon/ceramic/viton
|
1337.40 |
|
|
MP Pump 39467, Flomax 100 Series Self-Priming Centrifugal, 1" X 1" Connections
The FMX100 self-priming centrifugal pump is constructed of 316 SS for superior corrosion resistance and compatibility with most fluid types. A carbon / ceramic / viton mechanical seal is standard. With a maximum flow of over 55 GPM and pressure capabilities of nearly 60 feet, this rugged self-priming pump is capable of 17 feet suction lift when operating at 3450 RPM.
The FMX100 has numerous applications in industries such as: construction, petroleum, diesel exhaust fluid, marine and marine air conditioning, agriculture for biocides and liquid fertilizers, and numerous industrial applications such as brine and calcium chloride. 316SS Self Prime Pump for chemicals, salt water or many other liquids where corrosion is a problem. Marine Boat air conditioning is a big market for these pumps. Model FRX 75-SP is a high performance self-priming 316 stainless steel centrifugal pump.
The O-ring / flapper design enhances the self-priming capability to 12 foot suction lift. Marine ignition protected motors available. 316 Stainless Steel (Investment Cast). 1/8" NPT Fill Port.
Originally designed for marine air conditioning installations when the pump mounting location is prone to air-lock or requires a suction lift. Even when a pump is mounted below the waterline an air-lock can occur due to hull motion when the vessel is underway. Pump will purge air from the system and eliminate “Air-Lock; from becoming an irritating issue.;
1" x 1" Self Priming Centrifugal Pump
APPLICATION: Agricultural, Commercial, Industrial, Marine
MATERIALS OF CONSTRUCTION: 316 stainless steel
FLOW: Up to 55 GPM
HEAD FEET: 60'
IMPELLER: 4.0"
DRIVE OPTIONS: Close Coupled 1 HP TEFC IEC80B34 Motor, Close coupled 3/4HP TEFC IEC80B34 Motor, Engine Mount for 5/8" Shaft, Pedestal Hydraulic
SEAL: Type 6A carbon/ceramic/viton
DISCHARGE: 1"
SUCTION: 1"
|
1337.40 |
|
|
March 809 BRC HS 24VDC Mag-Drive Centrifugal Pumps Bronze 24VDC High Speed 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 24VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
501.56 |
|
|
MP Pumps 21380 Flomax 15 NPT Self Priming Centrifugal Pump
Pedestal Drive Bronze, 6.0" Impeller, 3" x 3"
MP Pumps Flomax 15, 3" NPT Flomax self priming centrifugal pumps. Up to 300 GPM, up to 125' head (54 PSI), 3450 RPM. Available in all bronze construction.
Removable flanges and replaceable wear plates protect the housing and eliminate wear. All fasteners are Stainless Steel. Standard mechanical seal have Viton elastomers.
Specifications
Rated Capacity 300 GPM Maximum Discharge Pressure: 125 feet (54 PSI)
Suction & Discharge Connections: 3" X 3" FNPT
Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve, 304 stainless steel stub shaft; viton mechanical seal.
This item is 'build to order'.
|
6366.98 |
|
|
MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump
MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 15
Part #: MP21381
Size: 3 in. NPT
Flow-Rate: 320 GPM
Head Feet: 145
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
OEM
|
1762.20 |
|
|
MP Pumps 21383 FM 15 BRONZE PUMP
MP Pumps 21383, FLOMAX 15 Self Priming Centrifugal Pump, Wet End Only
FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators and Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
3" X 3" NPT Ports
Capacity up to 320 GPM
Total Head up to 145 feet
Bronze construction
5.75 inch diameter impeller
|
6386.81 |
|
|
March 809-BR 24V Mag Drive Pump
Applications for the 809-BR 12V & 24V Magnetic Drive Pump include hot water systems, refrigeration systems and solar heating.
March Pump's industrial 809-BR 12V & 24V is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 5 gallons per minute at 1.5 feet, and its maximum head is 7 Feet (or around 3PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.01 Horsepower DC Brush Type Motor, available in 12 or 24 Volts. The 12 Volt motor has an operating range from 0 to 14 Volts, and the 24 Volt motor has an operating range from 0 to 26 Volts. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Max Flow
5 GPM
18.9 LPM
Max Head
7.1 FT
2.1 M
Power
.01 HP
.007 KW
Electrical
12V Range 0-14 or 24V Range 0-26
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Bronze (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
|
465.08 |
|
|
MP Pumps 35643, Petroleum 8 Self Priming Centrifugal Pump
2" x 2" Capable of creating vacuum sufficient to lift liquids up to 25 feet.
PO8PMP C: 3-3 56C FA 5.0 T-21 NRS
Ships via Truck Only. Please use the Contact Us page for a shipping quote.
|
1833.30 |
|