Rugged shipper converts quickly to countertop merchandiser containing 12 universal pitot tubes. These pitots replace almost any brand without drilling new holes, have an automatic kick up feature to prevent transom damage, and can be used with any pressure driven speeds up to 80 MPH.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

FL-18 ProPack II w/12º Ice Ducer The FL-18 boasts features and performance previously not available on a three-color flasher depth finder / fish finder. The FL-18 offers a patented split screen flasher display. This allows you to zoom-in on the bottom six feet while watching the entire water column at the same time in real time! You will be amazed at the performance for bass fishing, walleye fishing, and pan fish on both open water and ice fishing. The Bottom Lock feature stays locked on the bottom even as the boat is bouncing up and down in big waves! The Auto Zoom mode is fantastic for watching Perch or Walleye while ice fishing. These fish commonly hold tight on the bottom, and with a target ID of less than 1/2 inch, the FL-18 makes them easy to spot! And that's not all. The FL-18 depth finder / fish finder is equipped with features like a built-in shallow water mode for fishing waters under 15 feet. Five depth scales down to 200 feet for the standard model, and down to 300 feet for the custom deep model. Built-in interference rejection. A three color LED readout that tells you if the targets you see are weak (green) medium (orange) or strong (red). This three color LED technology has proven to be the most reliable and accurate way of understanding where fish are holding. Vexilars most popular winter fishing system is the Pro Pack II. This system offers great performance features in a super durable case with a built-in gimbal bracket to support your flasher. The Pro Pack II System is offered with the FL-20, FL-18, FL-8se and FL-12 units. Standard features include a rod holder, tackle box, universal transducer holder, cable holding cleats and a 12 Volt, 9 amp-hour battery with charger. The Pro Pack II has been designed to fit into a five gallon bucket, and has an optional soft pack carrying case available. The Pro Pack comes completely assembled, individually tested and ready to fish with. It also includes an instructional DVD. Features Auto Zoom Mode (AZ) - Gives a half screen zoom window of the bottom six feet of depth. No matter if you're in 10 feet or 100 feet, the bottom six feet always fills half of the screen. This gives you resolution never before possible in deep water Bottom Lock Mode (BL) - Works the same as Auto Zoom, but locks the bottom so it will not move with changes in depth or boat motion. Spot a Walleye near the bottom at 40 m.p.h.! Low Power Mode (LP) - Reduces the output power by 50%. This feature takes the place of the Vexilar S-Cable. Both the AZ and BL modes are available within the LP mode. Super Bright and Rock Solid Display - The new Light Emitting Diodes along with a high power driver circuit and a screaming fast wheel speed gives the FL-18s display unmatched brightness and signal clarity. Five Depth Ranges - The Standard FL-18 includes 20', 40', 60', 80', and 200 foot ranges. The Deep Range unit includes 30', 60', 90', 120', and 300 foot ranges. Interference Rejection - Pressing in on the Gain knob cycles you through ten different IR setting to allow you to knock out interference from another close by depth finder. Vexilar 12 volt, 9 amp-hour battery delivers long lasting power. Pack comes complete with charger. FL Digital Depth Indicator. Gives depth and helps keep track of your battery level. Two cable holding cleats. Adjustable rod holder with two possible mounting locations. The patented Ice-Ducer system is a self leveling transducer with float for accurate transducer positioning every time. Easy access to tackle box Pro Pack case fits inside a five gallon bucket. Pre-drilled holes for optional accessories Universal transducer holder (on the back) Two-year warranty (Pro-rated on battery) Specifications High Resolution Display: 525 Bits High-Speed Real-Time LED Readout Backlit Depth Scale for Easy Visibility in Low Light Conditions Three-Color Display: Red = Strong Signal / Orange = Medium / Green = Weak Five Depth Scales: 20', 40', 60', 80', and 200' * Exclusive Interference Rejection: 10 Step Power and Sensitivity: 400 Watts Peak-to-Peak Frequency: 200 kHz Target Separation: 2.65" Target ID: .5" Weatherproof High Impact Case Dimensions: 4.4"H x 6"W x 2.5"D - Weight: 1.1 Lb. Voltage: 12 VDC - Current draw: 200 MA CE Certification: A001P100713005E WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

316 SS Non-Perforated Worm Gear Hose Clamp - 15/32" Band - (7/8" – 1-1/4") Clamping Range - 10-Pack - SAE Size 12 Premium Marine Grade, all AISI 316 (high tensile strength) Stainless Steel “HD NON-PERF” Worm Gear Hose Clamp. The 11.7 mm (0.46”) wide band is Non-Perforated and Smooth on the inside with Rolled Edges. This eliminates hose damage with increased clamping force. The High Strength, Compact, One Piece 16mm (0.63”) wide Housing provides one of the highest clamping force ratings of any worm gear style clamp.   Features: The screw head is 7mm Long service life and safety for most general-purpose hose applications and connections Recommendations: Measure hose O.D. before selecting clamp size for proper fit Double clamp on each hose end for critical applications Consider using our #720 Series wide band 316 SS T-Bolt Clamps for larger I.D. hoses (i.e. Exhaust Hose, etc.) Construction: Band & Housing: 316 Stainless Steel 11.7 mm wide band – 0.9mm thick Screw Drive: 316 Stainless Steel 7.0 mm screw head Specifications: SAE Size: 12 Hose Inner Diameter: (inch) 5/8" – 1-1/8" Clamping Range: (inch) 7/8" – 1-1/4" / (mm) 22-32 Recommended Torque Inch lbs: 35-45

FLX-12 Pro Pack II with 12° Ice Ducer A Pro Pack carry case fits into a five gallon bucket for transport and offers a rod holder and tackle box too. When you put the FLX-12 using Vexilar’s brushless data transfer technology, you get a sunlight readable display with a built in low power mode and ranges to 120 feet. This pack is ready for the ice right out of the package with a 12 degree Ice Ducer transducer. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

FLX-20 Pro Pack II with 12° Ice Ducer & DD-100 Versatility is the key to success and the FLX-20 delivers! With two Auto Zoom zone options, one for the zooming in on the bottom six feet and one for the bottom twelve feet, there is nowhere those bottom loving fish can hide.  From the 300 foot max depth range to the night mode for easy viewing in low light conditions, nothing rivals the FLX-20 for superior, multi-use performance, shallow or deep, day or night.  The Pro Pack II carry case with the FLX-20 is a very powerful combo to have at your fingertips while ice fishing. The Pro Pack is designed to fit inside a 5-gallon bucket for safe transport but also offers other features like a rod holder and tackle box.  Comes standard with a DD-100, to give you a Digital Depth Display while fishing and also battery status.  Also standard is a 12 volt-9 Amp hour battery and fully automatic digital charger.    Rod holder and tackle box also come standard along with a 12 degree Ice Ducer transducer.  This model has most of the features anglers love like two bottom Zoom-Zones that allow you to target fish in the bottom 6 foot or 12 foot of the water column no matter how deep you fish! It has innovative features like a low power option for fishing in shallow water and now, the ability to use the zoom feature in low power.  The FLX technology will give you a 20% brighter and sharper display.  This powerhouse of a unit offers 10-foot depth ranges and deliver deep water performance to an impressive 300 feet.   Features: FLX three-color display technology Night and low power mode Low Battery Alert display  Two zoom zones  Low power 6’ zoom option  20 Step IR settings Target ID of less than ¼ inch  Technical Specifications: Range - 300 feet  10-foot depth ranges to 40 feet   525 lines of resolution Weight 13 pounds  Operating voltage - 10.5-15 Volts   In the Box: FLX-20 Fish finder 12 volt - 9 amp hour battery and charger Vexilar tackle box Pro Pack II Carry case 12 degree Ice Ducer transducer   DD-100 Digital depth & battery gauge Instruction manual  *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Boat Outfitting Equipment and Supplies When it comes time for outfitting your boat, you can get all your boating supplies and boating accessories from us. You will never need to go anywhere else for your boat outfitting, because we have all the boat supplies you need. If you're looking for anchors/chain/rope, anodes, antifouling systems or boarding ladders, we have you covered. We can also offer you a selection of bottom paint and bow thrusters to choose from. You may also want cleaning supplies that offer deck/galley options so you can get your boat sparkling and ready to enjoy. We also have display mounts and docking accessories to complete your outfitting needs.

Measures velocity of fluid flow. Slotted mounting plate allows easy replacement of all popular pitots. No drilling required for replacement installation. For speedometers up to 80 mph.

Reactor™ 40 Hydraulic Corepack with SmartPump v2 & GHC™ 50 Autopilot Instrument Pack Every Captain Needs a Co-Pilot. Designed for powerboats, this Reactor 40 hydraulic corepack with SmartPump v2 and GHC™ 50 display gives you the extra hand you need, so you can explore paradise worry-free.  Features: This Reactor 40 corepack is the perfect companion for your hydraulically steered system. With its advanced solid-state 9-axis AHRS, you can mount Reactor 40 nearly anywhere, in any orientation.  It even reduces power consumption, minimizes heading error, and more. Even when you’re pitching or rolling, this autopilot reacts to sea conditions to keep you on course. You just want to get on the water, so we made calibration fast and easy.  That’s the power of simplicity. Control your autopilot from anywhere on your boat by using your compatible Garmin devices, including the Reactor autopilot remote, select quatix® marine smartwatches, and more (requires a compatible Garmin chartplotter or GHC 50 autopilot instrument.) The SmartPump v2 is a one-size-fits-most solution that provides optimal control and confidence on the water. Plus, gain better thermal performance, higher reliability, and lower power consumption. Gain more freedom when maneuvering your boat.  This corepack allows for optional Shadow Drive technology to automatically disengage the autopilot when you turn the wheel. Want more?  The optional GHC™ 50 autopilot instrument enhances your autopilot experience. When connected to your compatible Garmin chartplotter, all Reactor 40 corepacks offer powerboat and sailing features, including heading hold and step turns — plus wind hold and tack/jibe when paired with a wind sensor (sold separately.)  Technical Specifications - SmartPump v2: Dimensions (H x W x D) - 7 3/4" x 7 1/2" x 9 5/8" (197 mm x 190 mm x 244 mm) Weight - 16.5 lbs (7.5 kg) Temperature range - From 5°F to 131°F (from -15°C to 55°C) Material - Electronics Control Unit (ECU) - fully gasketed, aluminum alloy.  Bracket - carbon steel.  Manifold - aluminum alloy.  Motor - aluminum alloy Power cable length - 9 ft (2.7 m) Power input - 11.5-30 Vdc Fuse - 40 A, blade-type Main power usage (standby) - less than 1 A. Main power usage (engaged) - 5-10 A and peak - 34 A Flow rate - Configurable from 0 to 2.4 L per minute Compatible with steering cylinder sizes from 4-24 cu in.  7-second lock to lock up to 17 cu in Technical Specifications - CCU: Dimensions: 3 19/32" diameter (91.4 mm) Weight: 5.6 oz (159 g) Temperature range: From 5°F to 131°F (from -15°C to 55°C) Case material: Fully gasketed, high-impact plastic, waterproof to IEC 529 IPX7 standards CCU cable length: 9.5' (3 m) NMEA 2000 power input: 9-16 V NMEA 2000 LEN: 3 (150 mA) Technical Specifications - Buzzer/Alarm: Dimensions (L × Diameter) - 29/32" × 1.0" (23 mm × 25 mm) Weight - 2.4 oz (68 g) Temperature range - from 5°F to 131°F (from -15°C to 55°C) Cable length - 10' (3.0 m) Technical Specifications - Reactor 40: Unit dimensions (W x H x D) - 4.3" x 4.4" x 1.9" (10.9 x 11.2 x 4.8 cm) Display resolution (W x H) - 320 x 240 pixels Display Type - QVGA color LCD display NMEA output - NMEA 2000 Supply voltage - 10 to 20V Operating temperature - -15° C to 70 C° (5° F to 158° F) Technical Specifications - GHC™ 50: Dimensions (H x W x D) - 5.5” x 4.1” x 2.0” (14.0 x 10.5 x 5.1 cm)  Display Type - 800 x 480 WVGA Display Size - 5" (12.7 cm) Touch Display - Yes Knob Control - With GRID 10/20 Remote Control via ANT+® Connectivity - Yes Wi-Fi Connectivity - Yes NMEA 2000 Networking - Yes Ethernet - Yes What's in the Box? GHC™ 50 Marine Autopilot Display SmartPump v2 Reactor 40 CCU (Course Computer Unit) ECU (Electronic Control Unit) power cable Interconnect cable Shadow Drive Buzzer NMEA 2000® drop cables (2 meters) NMEA 2000 power cable NMEA 2000 T-connectors Male and female terminators Documentation *Sold as an Individual 

iSeaSense Wireless Speed Depth Temp Pack Digital Yacht iSeaSense is a new range of complete marine instrumentation packs based on NMEA 2000 and wireless connectivity – allowing for maximum flexibility and connectivity. Choose from using phones, iPads, and tablets for boat data displays as well as 3rd party industry-standard instruments and multi-function displays. Top quality and highly accurate sensors are used for boat depth, speed, compass, and GPS data. Data can be shared with other devices on the NMEA 2000 network too. iSeaSense is easy to specify. Available as two main starter packs, everything is included for easy installation and ordering.  No app is needed either as the iSeaSense wireless server creates powerful graphical and numeric display pages that can be viewed via a browser on any device. iSeaSense Pack 1 is a comprehensive boat depth, speed, and temperature pack.  A spatial sensor is also included for detecting pitch and roll and there’s a sophisticated algorithm for calibrating boat speed information based on heel. A full NMEA 2000 backbone cabling pack is included and the wireless interface for connectivity. There is a spare cable and connection point for additional NMEA 2000 devices such as a multi-function display or Digital Yacht’s range of instruments. iSeaSense features an easy-to-use web interface.  No apps are required. Simply open the browser on a connected device, navigate to iSeaSense.local, and the optimized touchscreen display is ready. The web interface works on iOS, Android, PC, Linux, and MAC – any standard web browser as well as e-ink displays like Kindle and e-book. It supports up to 3 connected devices with super fast 5Hz updates. The data can also be used by 100’s popular navigation apps & software such as Navionics, TZ iBoat, OpenCPN, SailGrib, etc. Operation You can access the iSeaSense dashboard through its own web interface, just open your web browser, enter the iSeaSense’s IP address or iSeaSense.local and you will access the attractive dash to display all your instrument's data. So no complicated programming software or app is required. By default, iSeaSense has a series of pre-defined pages that display digital databoxes and analog “instruments” of the instrument and navigation data available on the NMEA 2000 network. With iSeaSense you’re in control of the data you see. The pages are fully editable, so any databox can be configured for the information you want and you can easily add and remove databox to build your perfect display.  The configuration can also be saved and shared – ideal for standard configurations for production boats and OEMs. iSeaSense Pack Features: Pack includes iSeaSense wireless server, NMEA 2000 cabling, and advanced boat depth, speed, and temperature transducer with pitch and heel sensor iSeaSense server creates beautiful graphic display pages of data with fast 5Hz updates viewable on any smartphone, tablet, or iPad Advanced calibration routing is available for the transducer with corrections for the boat heel and transducer location Includes extra NMEA 2000 T piece for system expansion allowing easy addition of sensors or displays Interface Features: NMEA 2000 interface and wireless gateway for iSeaSense system. Integrated instrument display page server. Configurable display pages for depth, speed, temp, time, GPS, wind, navigation, and compass Network diagnostics, settings, and calibration capability Data logging Self-powered from NMEA 2000 backbone Integrated wifi antenna typically footprints boats up to 20m Supports additional TCP/IP and UDP data connections for 3rd party apps on up to 7 connected devices (outputs GPS, AIS, depth, wind, and speed information from NMEA 2000 bus) Transducer Features: Transducer for depth, boat speed, water temperature, and boat heel/pitch with fast, super accurate 5Hz speed updates from 0.3 to 45 knot Data Update Rate: Depth: 1X/second, Speed: 5X/second, Heel/Trim: 10X/second 235KHz depth operation to minimize interference with 50/200KHz fish finders and sounders Max depth 100m Supports up to 22-degree hull deadrise Supplied with 6m NMEA 2000 cable and self-powered from iSeaSense NMEA 2000 backbone Standard 2” thru hull size/diameter Includes Bluetooth interface for advanced calibration and set-up features if required Stainless steel and bronze skin fittings available as an option

iSeaSense Wireless Speed Depth Temp Pack Plus Wind Digital Yacht iSeaSense is a range of complete marine instrumentation packs based on NMEA 2000 and wireless connectivity. This pack includes speed, depth, temperature transducer plus wind sensor. Digital Yacht iSeaSense is a range of complete marine instrumentation packs based on NMEA 2000 and wireless connectivity, allowing maximum flexibility and connectivity.  Choose from using phones, iPads, and tablets for boat data displays as well as 3rd party industry-standard instruments and multi-function displays. Operation: You can access the iSeaSense dashboard through its web interface, just open your web browser, enter the iSeaSense’s IP address or iSeaSense.local and you will access the attractive dash to display all your instrument data. So no complicated programming software or app is required. By default, iSeaSense has a series of pre-defined pages that display digital databoxes and analog “instruments” of the instrument and navigation data available on the NMEA 2000 network. With iSeaSense you’re in control of the data you see. The pages are fully editable, so any databox can be configured for the information you want and you can easily add and remove databox to build your perfect display.  The configuration can also be saved and shared – ideal for standard configurations for production boats and OEMs. Key Features: Top quality and highly accurate sensors are used for boat depth, speed, wind, compass, and GPS data.  Data can be shared with other devices on the NMEA 2000 network too. iSeaSense is easy to specify. Everything is included as two main starter packs for easy installation and ordering.  No app is needed either as the iSeaSense wireless server creates powerful graphical and numeric display pages that can be viewed via a browser on any device. iSeaSense includes the WND100 wind sensor with 20m cable and an interface to “T” directly to the NMEA 2000 backbone.  It means there’s no heavy NMEA 2000 cabling to the top of the mast and no need for complex mast top terminations for the Wind Sensor. iSeaSense also includes depth, speed, and temperature sensors.  A spatial sensor is also included for detecting pitch and roll and there’s a sophisticated algorithm for calibrating boat speed information based on heel. A full NMEA 2000 backbone cabling back the wireless interface for connectivity and a spare cable and connection point for additional NMEA 2000 devices are included. With NMEA 2000, expanding the system is easy and you can add any Digital Yacht’s instruments such as GPS, AIS, electronic compass, and more. You can also send the instrument data to your NMEA 2000 chart plotter or display. iSeaSense features an easy-to-use web interface.  No apps are required. Simply open the browser on a connected device, navigate to iSeaSense.local, and the optimized touchscreen display is ready. You can calibrate the wind sensor via the iSeaSense web interface and also displays true and apparent wind speed and angle plus VMG calculations. The web interface works on iOS, Android, PC, Linux, and MAC – any standard web browser as well as e-ink displays like Kindle and e-book. It supports up to 3 connected devices with super fast 5Hz updates. The data can also be used by 100 popular navigation apps & software such as Navionics, TZ iBoat, OpenCPN, SailGrib, etc. iSeaSense Pack Features: Pack includes iSeaSense wireless server, NMEA 2000 cabling, and advanced boat depth, speed, and temperature transducer with pitch and heel sensor Pack also includes WND100 mast head wind sensor – adding wind data to the system and network Easy to install mast head unit with 20m cable and NMEA 2000 interface iSeaSense server creates beautiful graphic display pages of data with fast 5Hz updates viewable on any smartphone, tablet, or iPad Advanced calibration routing is available for the transducer with corrections for the boat heel and transducer location Calibrate the wind sensor via the iSeaSense interface Includes extra NMEA 2000 T piece for system expansion allowing easy addition of sensors or displays Interface Features: NMEA 2000 interface and wireless gateway for iSeaSense system. Integrated instrument display page server. Configurable display pages for depth, speed, temp, time, GPS, wind, navigation, and compass Network diagnostics, settings, and calibration capability Data logging Self-powered from NMEA 2000 backbone Integrated wifi antenna typically footprints boats up to 20m Supports additional TCP/IP and UDP data connections for 3rd party apps on up to 7 connected devices (outputs GPS, AIS, depth, wind, and speed information from NMEA 2000 bus) Transducer Features: Transducer for depth, boat speed, water temperature, and boat heel/pitch with fast, super accurate 5Hz speed updates from 0.3 to 45 knot Data Update Rate: Depth: 1X/second, Speed: 5X/second, Heel/Trim: 10X/second 235KHz depth operation to minimize interference with 50/200KHz fish finders and sounders Max depth 100m Supports up to 22-degree hull deadrise Supplied with 6m NMEA 2000 cable and self-powered from iSeaSense NMEA 2000 backbone Standard 2” thru hull size/diameter Includes Bluetooth interface for advanced calibration and set-up features if required Stainless steel and bronze skin fittings available as an option Wind Sensor Features: The WND200 package comprises a WND100 mast head unit plus iKonvert NMEA 0183-2000 interface supporting 5Hz fast wind mode 8-18V power with ultra-low 25mA power consumption Supplied with 20m ultra thin 4mm masthead cable for easy cable runs through mast (4 core screened) iKonvert NMEA 2000 interface included for system integration Wind angle accuracy is better than 4 degrees Wind speed accuracy better than 3% Min wind speed 1.7 knots – max 80 knots Settling time typically 1.3 seconds

FLX-20 Genz Pack with 12° Ice Ducer This affordable package contains the Genz Pack carry case. The FLX-20 offers Vexilar brushless data transfer technology for a sunlight readable display with a built in low power mode and ranges to 120 feet. This pack is ready for the ice right out of the package with a 12 degree Ice Ducer transducer. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

IG017 Ignition Pack for Yamaha Outboard Engines This ARCO ignition pack is designed for specific Yamaha outboard engines. Fits: Yamaha 9.9 (1984-95), 15 (1984-95), C25 (1990-97) Mariner 9.9, 15, 20 & 25HP Replaces: YAMAHA Ignition Pack 695-85540-11-00 YAMAHA Ignition Pack 695-85540-12-00 YAMAHA Ignition Pack 695-85540-10-00 MERCURY Ignition Pack 43077T MERCURY Ignition Pack 43077M MERCURY Ignition Pack 96450M SIERRA Ignition Pack 18-5131 CDI ELECTRONICS Ignition Pack 117-695-11 Warranty Information When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications. Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.

12" x 18" Super Strong Trim Tab Kit w/o Switch -12V -Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part # 15056-002 (Super Strong 12-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 24' to 40' Length of Tab: 12" Width of Tab: 18" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 24" Super Strong Trim Tab Kit w/o Switch -12V -Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part # 15056-002 (Super Strong 12-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 27' to 44' Length of Tab: 12" Width of Tab: 24" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.