SnapIt! Marine BRK Pontoon Boat Universal Mounting Bracket Universal Mounting Bracket. The use of additional mounting brackets allows the option of utilizing the removable accessories at different locations on the boat. Color: White.

SnapIt! Marine P003 Flush Mount Pontoon Quad Drink Holder This Quad Drink Holder is sized to fit can drinks with insulated sleeves and many mugs. The mug opening diameter is 3.625”. Interior Dimension are 3.895x8.12”. Overall Height 3.86”. Overall Width 18.4”. Cutouts on top ring can be useful for hanging sunglasses, etc. Flush mount unit not suited for use in combination with P0011 tables. Mounts permanently to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included. Color: White

SnapIt! Marine P005 Top Mount Pontoon Quad Drink Holder Quad Drink Holder sized to fit can drinks with insulated sleeves and many mugs. Mug Opening Diameter 3.625”. Interior Dimension 3.895”(3.45” at narrowest point)x8.12”. Overall Height 3. 6”. Overall Width 18.4”. Top mount unit can be used in combination with P0011 tables. Mounts permanently to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included. Color: White.

Universal Mounting Bracket Kit Our unique, three-sided bracket design features three precise angles that take into account the majority of the trailers' diverse tie-down tab designs.The three-sided bracket enables the BoatBuckle G2 to be moved several different ways,making it truly universal.

SnapIt! Marine P001KR Pontoon Boat Single Drink Holder Single Drink Holder sized to fit can drinks with insulated sleeves and many mugs. I.D. 3.625” Overall Height 3.5”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included. Color: White.

SnapIt! Marine P004CR Small Convertible 2 in 1 Drink Holder This is sized to fit can drinks or 20 oz plastic soft drink bottles. Space saving unit conveniently opens to hold two drinks when needed. I.D. 2.9” Overall Height 4.5”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included. Color: White.

Single Drink Holder sized to fit can drinks and 20 oz plastic soft drink bottles. I.D. 2.925” Overall Height 3.5”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.  Color:  White.

Double Drink Holder sized to fit can drinks with insulated sleeves and many mugs. Interior Dimension 3.625”(2.9” at narrowest point)x7.85”. Overall Height 3.8”. Cutout on top ring can be useful for hanging sunglasses, etc. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.  Color:  White.

Convertible 2 in 1 Drink Holder This is sized to fit can drinks with insulated sleeves. Space saving unit conveniently opens to hold two drinks when needed. I.D. 3.6” Overall Height 4.5”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.  Color:  White.

Large Handheld Electronics Holder. Opening is oval in shape. Interior Dimensions at the widest point are 3.15”x1.8”. Top ring has an additional ¼” clearance for belt clips. Overall Height 4.4”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.

Small Handheld Electronics Holder. Interior Dimensions at the widest point are 2.3”x1.7”. Overall Height 4.4”. Comes with universal mounting bracket which allows the use of a variety of accessories in one location. Mounting bracket permanently mounts to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.

RAM 1.5" Diameter Ball Mount with 6.25" X 2" Rectangle Base, STANDARD LENGTH Double Socket Arm & 2.5" Round Base The RAM-111U, powder coated marine grade aluminum mount, consists of a double socket arm mount, one 2.5" diameter round base with 1.5" rubber ball and flat 6.25" x 2" rectangular plate. The plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more. Rubber ball, socket technology dampens shock and vibration, as well as allows for almost infinite adjustment, perfect viewing angles. For most applications, mount will support up to ten pounds. Material: Powder Coated Marine Grade Aluminum Note: The "U" in the part number reflects product packaged in poly bag. For mounting a GPS puck antenna to this mount, RAM recommends the RAM-338U

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

SnapIt! Marine P0011 Folding Lunch Table for Pontoon Boats   This Folding Lunch Table for Pontoon Boats measures 21”x13.5”. Lunch table mounts permanently to 1 ¼” square rail commonly found on pontoon boats. Self supporting it folds down and out of the way when not needed.   No drilling required. All mounting hardware included. Color: White.   Custom made at time of order, none returnable.

Universal Mounting Pad. 3”x6”. Useful for mounting GPS, Fish Finder, Speakers, etc. with rectangle bases. Mounting angle is adjustable. Mounts permanently to 1 ¼” square rail commonly found on pontoon boats. No drilling required. All mounting hardware included.  Color:  White.