Solenoid Switch - 12V 12V solenoid for the BOW50/55/60/75 bowthrusters

Solenoid Switch - 24V - Pair Replacement 24v solenoid pack for the Vetus Bow and Stern thruster models 95, 110, 125 and 160Kgf. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

7718 - ML-Series Solenoid Switch - Stripped Wire - 12V For applications where sustained control signals are needed to emulate a normally open relay with a lower current draw. Features: Silver alloy contacts provide high reliability for switching live loads LED output to remotely indicate switch state  3/8"- 16 tin-plated copper studs for maximum conductivity and corrosion resistance One-piece stainless flange nuts for safe and secure connections Label recesses for circuit identification Technical Specifications: Control Circuit Voltage - 10.1 to 16.5 V DC Control Circuit Connection - Tinned wire Nominal Voltage - 12V DC Coil Function - Auto-releasing Amperage Operating Current - OFF - 8mA and ON 13mA Mechanical Endurance - 100,000 Cycles Terminal Ring Diameter Clearance - 1.18" (30mm) Terminal Stud Length - .875" (22mm) Terminal Stud Size - 3/8" - 16 (M10) In the Box: 7718 Solenoid Contura Switch w/integrated LED Instruction Manual  *Sold as an Individual

7718100 - ML-Series Solenoid Switch - Deutsch Connector - 12V For applications where sustained control signals are needed to emulate a normally open relay with a lower current draw. Features: Silver alloy contacts provide high reliability for switching live loads LED output to remotely indicate switch state  3/8"- 16 tin-plated copper studs for maximum conductivity and corrosion resistance One-piece stainless flange nuts for safe and secure connections Label recesses for circuit identification Technical Specifications: Control Circuit Voltage - 10.1 to 16.5 V DC Control Circuit Connection - Deutsch DTM Nominal Voltage - 12V DC Coil Function - Auto-releasing Amperage Operating Current - OFF - 8mA and ON 13mA Mechanical Endurance - 100,000 Cycles Terminal Ring Diameter Clearance - 1.18" (30mm) Terminal Stud Length - .875" (22mm) Terminal Stud Size - 3/8" - 16 (M10) In the Box: 7718100 Solenoid Contura Switch w/integrated LED Instruction Manual  *Sold as an Individual

L Solenoid Switch - 12-24VDC - 250A Features: Hermetically sealed contacts / vaporproof Ignition protected - safe for installation aboard gasoline powered boats Activated by an ON-OFF switch mounted anywhere Integrated coil control minimizes heating and amperage draw 450 Amp Class Designed for 12 or 24 Volt systems Ignition protected -- safe for installation aboard gasoline-powered boats Activated by a low amperage ON-OFF switch mounted anywhere Specifications: Control Circuit Connection: 20 AWG Tinned Wire Nominal Voltage: 12V DC / 24V DC Coil Function: Normally Open Mounting: #10 Operating Amperage Current: 3.6A when changing state Amperage Operating Current: 0.13A @ 12 V / 0.07A @ 24 V Terminal Stud Torque: 90 in-lb (10.17 Nm) Continuous Rating: 250A Using 1/0 Wire Size / 300A Using 2/0 Wire Size / 400A Using 4/0 Wire Size / 450A Using 2 x (2/0) Wire Size Intermittent Rating: 275A (5 min) Using 1/0 Wire Size / 400A (5 min) Using 2/0 Wire Size / 500A (5 min) Using 4/0 Wire Size / 600A (5 min) Using 2 x (2/0) Wire Size Cranking Rating 30 sec: 1,000A / 1000A DC Contact Form: SPST-NO Input Voltage: 9-36V DC Inrush Rating: 0.25 sec (10 repeats): 2000A Switching Cycles: 1,000,000 Terminal Stud: Serrated Flange Nut Terminal Stud Length: 0.66" (16.76mm) Terminal Stud Size: 5/16" (M8) Weight: 1.00lb (0.45 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Continuous Duty Solenoid - 200A - 12V Relays are commonly referred to as remote-acting switches and Littelfuse manufacturers a broad range of styles to meet your application. To ensure you are utilizing the proper remote-acting switches, review the attributes in the specifications tab below against your application requirements. Specifications: Current Rating (Continuous) in Amps: 200 Circuitry: SPST Normal Position: Normally Open Contact Material: Silver Housing: Plated Steel

7719 - ML-Series Solenoid Switch - Stripped Wire - 24V For applications where sustained control signals are needed to emulate a normally open relay with a lower current draw. Features: Silver alloy contacts provide high reliability for switching live loads LED output to remotely indicate switch state  3/8"- 16 tin-plated copper studs for maximum conductivity and corrosion resistance One-piece stainless flange nuts for safe and secure connections Label recesses for circuit identification Technical Specifications: Control Circuit Voltage - 20.2 to 32.9 V DC Control Circuit Connection - Tinned wire Nominal Voltage - 24V DC Coil Function - Auto-releasing Amperage Operating Current - OFF - 8mA and ON 13mA Mechanical Endurance - 100,000 Cycles Terminal Ring Diameter Clearance - 1.18" (30mm) Terminal Stud Length - .875" (22mm) Terminal Stud Size - 3/8" - 16 (M10) In the Box: 7719 Solenoid Contura Switch w/integrated LED Instruction Manual  *Sold as an Individual 

7719100 - ML-Series Solenoid Switch - Deutsch Connector  - 24V For applications where sustained control signals are needed to emulate a normally open relay with a lower current draw. Features: Silver alloy contacts provide high reliability for switching live loads LED output to remotely indicate switch state  3/8"- 16 tin-plated copper studs for maximum conductivity and corrosion resistance One-piece stainless flange nuts for safe and secure connections Label recesses for circuit identification Technical Specifications: Control Circuit Voltage - 20.2 to 32.9 V DC Control Circuit Connection - Deutsch DTM Nominal Voltage - 24V DC Coil Function - Auto-releasing Amperage Operating Current - OFF - 8mA and ON 13mA Mechanical Endurance - 100,000 Cycles Terminal Ring Diameter Clearance - 1.18" (30mm) Terminal Stud Length - .875" (22mm) Terminal Stud Size - 3/8" - 16 (M10) In the Box: 7719100 Solenoid Contura Switch w/integrated LED Instruction Manual  *Sold as an Individual 

7765 L-Series Solenoid Switch - 150A - 12/24V DC Ideal for switching DC subpanels, thrusters, windlass, inverters, and other medium-amp DC loads. Features: Continuous duty, SPST - Normally Open Hermetically sealed contacts Activated by a remote ON-OFF switch 8230 (sold separately) Coil control circuit minimizes heating and amperage draw

PM Solenoid Pack - 12V Maxwell's PM Solenoid Pack that is 12V. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Reversing Solenoid Pack - 12V Maxwell Reversing Solenoid Pack 12V, replaces P19045.

Solenoid Valve - 12V 12V Electric Valve to be used with centralized fresh water system.  Features: Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance

Push-Button Switch - 12V Latching On/Off - Red LED Push-button Switches are built to last with their stainless steel components and silver alloy contacts. The through panel mount switches are ideal for lighting, switch, or dash panels, with colored rings that can be wired to either display power to the system or switch back lighting. The product line includes both switches and warning buzzers with LED light rings. Features: Maximum switch current rating 5 Amps IP67 environmental protection switches WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Push-Button Switch - 12V Momentary (On)/Off - Red LED Push-button Switches are built to last with their stainless steel components and silver alloy contacts. The through panel mount switches are ideal for lighting, switch, or dash panels, with colored rings that can be wired to either display power to the system or switch back lighting. The product line includes both switches and warning buzzers with LED light rings. Features: Maximum switch current rating 5 Amps IP67 environmental protection switches WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.