Roller Brush - 9" KiwiGrip rollers let you vary the texture of KiwiGrip non skid coating from fine to aggressive depending on the amount of surface traction desired. Use the roller to achieve the texture you desire. For aggressive non-skid allow coating to dry slightly then lightly roll again. 9" Roller Brush works well on larger boats.

Roller Brush - 4" KiwiGrip rollers let you vary the texture of KiwiGrip non skid coating from fine to aggressive depending on the amount of surface traction desired. Use the roller to achieve the texture you desire. For aggressive non-skid allow coating to dry slightly then lightly roll again. The 4" size is recommended for most jobs.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Hypro 4001C Roller Pump 9 Gpm Ci

Boat Outfitting Equipment and Supplies When it comes time for outfitting your boat, you can get all your boating supplies and boating accessories from us. You will never need to go anywhere else for your boat outfitting, because we have all the boat supplies you need. If you're looking for anchors/chain/rope, anodes, antifouling systems or boarding ladders, we have you covered. We can also offer you a selection of bottom paint and bow thrusters to choose from. You may also want cleaning supplies that offer deck/galley options so you can get your boat sparkling and ready to enjoy. We also have display mounts and docking accessories to complete your outfitting needs.

Oberdorfer 54-Brush Brush Set For 54-Series  

March BC-2CP-MD 24V DC BRUSH Part# 0125-0123-0200

March BC-2CP-MD 12V DC BRUSH Part# 0125-0123-0100

Type A Controller f/Boats with an Existing Autopliot No need for additional drive units. The Intellisteer Wireless Controller is designed to be wired between a Course Computer and Autopilot Drive When the Intellisteer Wireless Controller is activated it will disconnect the autopilot and provide wireless jog steering control from anywhere on the boat When the Intellisteer Wireless Controller is turned off, the Autopilot will function as before

Edge Mount Trim Tab Kit w/Standard Tactile Switch Kit Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Suggested Boat Length:16'-25' L" x W": 9" x 12" Hinge Height: 2" Minimum Transom Height: 13.5" Kit Contents 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads & Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner's / installation manual All necessary stainless steel mounting hardware Specifications: Blades: 12 Gauge Stainless Steel Finish:Smooth Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Standard Tactile Switch Kit With Built-In Retractor For Single Actuator Systems / 12-Volt Lenco Trim Tab Standard Tactile Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. The switch itself is completely waterproof, and has an over-molded connector to eliminate water intrusion. The standard tactile switch is built to all the same exacting standards as the indicator switches. Kit Contents Key Pad Control Box 36" Power Pigtail WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Edge Mount Trim Tab Kit w/LED Indicator Switch Kit Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Suggested Boat Length:16'-25' L" x W": 9" x 12" Hinge Height: 2" Minimum Transom Height: 13.5" Kit Contents 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads & Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner's / installation manual All necessary stainless steel mounting hardware Specifications: Blades: 12 Gauge Stainless Steel Finish:Smooth Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat LED Indicator Switch Kit With Built-In Retractor & Self-Check Features For Single Actuator Systems / 12 & 24-Volt Lenco Waterproof Trim Tab Tactile Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. The Lenco indicator switch is the most advanced trim tab switch available. The switch itself is completely waterproof, and has an over-molded connector to eliminate water intrusion. L.E.D. indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. The standard tactile switch is built to all the same exacting standards as the indicator switches. Kit Contents Self-contained sealed Key Pad Control box 36" Power Pigtail. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

KeelGuard® - 9' - Light Gray The Original Do-It-Yourself Keel Protector - Protect Your Investment Against Sand, Rocks & Ramps Wear and damage to your boat’s keel can break down its protective gelcoat finish, allowing water to reach and destroy the fiberglass laminates. Megaware KeelGuard®, the powerful abrasion-resistant protector, prolongs the life of your boat like nothing else. Megaware KeelGuard® Engineering Every aspect of the Megaware KeelGuard® has been designed with boat designers and 3M® engineers. Many factors contribute to its success. A precise, abrasive-resistant blend of polymers and urethanes achieve optimal durability and pliability. A pressure-sensitive adhesive creates strength, while permanently bonding and sealing Megaware KeelGuard®’s contoured edges to the hull surface. Angled grooves produce hydrodynamic channels, creating air pockets and providing a slicker surface. The perfect combination of these factors makes the Megaware KeelGuard® the easiest keel protector to install, and gives it unparalleled quality and dependability. Megaware KeelGuard® Colors & Sizes Megaware KeelGuard® comes in 11 great looking colors to match virtually any boat. All colors are UV-stabilized for true color that lasts a lifetime. Megaware KeelGuard® is available in nine standard lengths or can be ordered in custom lengths. Lifetime Warranty Megaware guarantees this Megaware KeelGuard® (to the original purchaser), against abrasive wear and adhesion failure during normal use of your boat, for as long as you own your boat. Features: Color: Light Gray KeelGuard® Size: 9' Boat Size up to 24' 3M® Technology 3M® Acrylic Pressure-Sensitive Adhesive Pliable & Tough Research & Technology Contoured Edge Protect Against Abrasive Sand, Rocks, Concrete Ramps and Oyster Beds Eliminate Costly Repairs Enjoy the Highest Quality and Superior Engineering Increase the Value of Your Boat 5” Width: Contact for Custom Sizes Made in the USA

KeelGuard® - 9' - Hunter Green The Original Do-It-Yourself Keel Protector - Protect Your Investment Against Sand, Rocks & Ramps Wear and damage to your boat’s keel can break down its protective gelcoat finish, allowing water to reach and destroy the fiberglass laminates. Megaware KeelGuard®, the powerful abrasion-resistant protector, prolongs the life of your boat like nothing else. Megaware KeelGuard® Engineering Every aspect of the Megaware KeelGuard® has been designed with boat designers and 3M® engineers. Many factors contribute to its success. A precise, abrasive-resistant blend of polymers and urethanes achieve optimal durability and pliability. A pressure-sensitive adhesive creates strength, while permanently bonding and sealing Megaware KeelGuard®’s contoured edges to the hull surface. Angled grooves produce hydrodynamic channels, creating air pockets and providing a slicker surface. The perfect combination of these factors makes the Megaware KeelGuard® the easiest keel protector to install, and gives it unparalleled quality and dependability. Megaware KeelGuard® Colors & Sizes Megaware KeelGuard® comes in 11 great looking colors to match virtually any boat. All colors are UV-stabilized for true color that lasts a lifetime. Megaware KeelGuard® is available in nine standard lengths or can be ordered in custom lengths. Lifetime Warranty Megaware guarantees this Megaware KeelGuard® (to the original purchaser), against abrasive wear and adhesion failure during normal use of your boat, for as long as you own your boat. Features: Color: Hunter Green KeelGuard® Size: 9' Boat Size up to 24' 3M® Technology 3M® Acrylic Pressure-Sensitive Adhesive Pliable & Tough Research & Technology Contoured Edge Protect Against Abrasive Sand, Rocks, Concrete Ramps and Oyster Beds Eliminate Costly Repairs Enjoy the Highest Quality and Superior Engineering Increase the Value of Your Boat 5” Width: Contact for Custom Sizes Made in the USA

Suncover for Axiom 9 when used with the Front Mounted kit A80500  Features: Rugged suncover protects your Axiom 9 from the elements Fits Axiom 9 models when fused with the front mounted kit A80500 Sleek design looks great on your boat NOT FOR USE WITH AXIOM PRO 9

9" x 12" Electro-Polished Standard Trim Tab Kit 12 Volt Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Blades areconstructed of 12-gauge 304 Electro-Polished stainless steel with a 5/8" flared trailing edge & 1/8" diameter stainless steel hinge pin. Kits include: (2) 12-gauge stainless steel Electro-Polished blades (2) 15054-001 actuator with 6' leads and Deutsch connectors (2) 30133-103 20' actuator extension wiring harnesses (2) 15085-001 upper mounting brackets with gland seal (2) 50014-001 lower mounting brackets Lenco owner's/installation manual Stainless steel mounting hardware Specifications: Boat Length:16' - 25' L" x W":9" x 12" Hinge Height:2" Minimun Transom Height:14" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.