Dual Locking Flush Deck Socket Mount Two attractive mirror polished 18-8 stainless steel flush deck socket sets, features a push button lock pin and includes a flange gasket with integral flip-up water seal cap.  These sockets mount flush for an uncluttered deck.  Compatible With: Dual Mounted Grills and Tables Technical Specifications: Material - 18-8 Stainless Steel Dimensions (installed) (W x H) - 2-5/8" x 1-15/32" (9.7 x 3.7 cm) Weight - 1.51 lb (.69 kg) *Sold as a Pair

Mount - Dual Locking Flush Deck Socket with Adjustable & Locking LeveLock Two attractive mirror-polished 18-8 stainless steel flush deck sockets and post sets. The posts are equipped with Magma's versatile LeveLock adjustable locking mount, allowing complete fore and aft adjustment of the table. A push-button lock pin allows use while underway. Sockets feature a flange gasket with an integral flip-up water seal cap. Some fasteners are required for installation. Specifications: Width: 3-7/16 in. (129 mm) Height Full Assembly: 6-1/16 in. (155 mm)  Height Installed: 4-3/16 in. (106 mm) Weight: 2.40 lb. (1.09 kg)

Single Locking Flush Deck Socket w/LeveLock Mount & Flange This 18-8 mirror polished stainless steel and hard anodized aluminum mount features Magma's LeveLock all angle adjustable locking mount, a push button locking pin and a flange gasket with the integral flip-up water seal cap.  Compatible With: Magma Rectangular Grills and Single Mount Tables  Technical Specifications: Material - 18-8 Stainless Steel and 356 Anodized Aluminum  Dimensions (W x H) - 2-5/8" x 6-1/16" (6.7 x 15.5 cm) Weight - 1.22 lb (.56 kg) *Sold as an Individual 

244 Flush Deck Mount With splash cover For all Scotty post mount rod holders Dimensions 4" x 2" x 2" Bolting Dimensions 1 5/16" x 3 3/16" WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Double Locking Stowable Pedestal Mount  Magma’s 28” locking pedestal mount for rectangular grills and single mount filet tables has a double locking mechanism that insures a secure fit for your boat or home application.  This double locking, Silver metallic anodized Aluminum, pedestal post locks into the surface mounting base and grill mounting bracket with (2) single push-buttons; allowing the entire assembly to be instantly installed or removed and stored for convenience.  The low-profile threaded twist-lock surface mounting base has been designed with a flush bottom so there is no need to cut a hole in your deck and measures just 5/8" tall and 7” diameter with a 5-3/4" bolt pattern.   With its versatility and convenience this is the perfect mounting option for boat swim platforms, boat decks, pontoon boats, or at home on the patio, balcony or deck. Technical Specifications:  Material - Anodized Aluminum Dimensions - Base Plate (H x W) - 17-15/16" x 7" (71 x 17.78 cm) Weight - 4.5 lb (2.05 kg) Mounting Application - Rectangular grills and Single mount tables *Sold as an Individual 

GS-500XL Outrigger Mounts *Only Accepts CF-HD Poles* When it comes to hardcore offshore sport fishing, the Pro Series GS-500 Outrigger Mount is the most durable, attractive, and functional base in the industry. The innovative design of the GS-500 enables anglers to adjust the lift and rotation of outrigger poles from the safety of the deck. This mount also features our patent-pending Twist & Lock pole connection and pairs exclusively with our award-winning Carbon Fiber Tele-Outriggers up to 24’ long.  Features and Benefits: TWIST & LOCK ARM Patent-pending design for easier, more secure pole connection Eliminates the need for pins or bolts when securing outrigger poles HANDLES Rotate and lift outrigger poles from the safety of the deck Heavy-duty, ergonomically shaped outward rotation handle Robust, dual-detented lifting crank handle locks flush into base MOUNT Bottom tube allows for it to operate on hard tops up to 4” thick Ideal for boats from 32 to 50-plus feet  Dredge load tested to handle a full, professional fishing spread  Absorbs the torque and whip created by outrigger poles  Constructed from cast stainless-steel and machined aluminum for a stronger, lighter base Includes matching 6”x 8"x ½” thick oval backing plates  Safety detents prevent uncontrolled rotation when deploying outrigger poles Allows a controlled 180° rotation, if needed Locking head eliminates downward creep of outrigger poles No port or starboard designation  Includes all mounting hardware for easy installation Pairs with 6º Wedge Plates (WP-500-6), sold separately Base hole pattern matches all TACO Marine Grand Slam models – making upgrades possible 3-year limited warranty

HD IP Flush Vertical Surface Mount - 3MP Max Resolution - 316L Marine Grade Stainless Steel - Recess Mount Dome Iris’ Sx76 series camera is the first of its kind designed to be installed into a bulkhead or vertical surface. Its waterproof stainless steel case is machined from marine-grade 316L stainless steel, which means it will not corrode in harsh saltwater environments, making it a great option as a backup or docking camera for boats. By mounting the camera on the sides of your boat, it can even be used when mooring alongside jetties or pontoons.  During installation, the camera’s inner ball can be adjusted and then locked into position by simply tightening the outer bezel to achieve the desired view.  For IP-based systems, the S476 features 3MP high-definition resolution and 12VDC or PoE power. As well as marine applications, the camera's tough case, and small footprint make it a perfect visibility aid for recreational vehicles, fire and rescue trucks, and other applications where a robust and reliable high-definition camera is required. The camera is certified to EN60945, EN55032, EN55035, and EN60529 (IP66) and is ONVIF compliant. For marine applications, the camera is directly compatible with Raymarine LH2 and above, Simrad, Lowrance, and B & G. For Garmin systems, use them in conjunction with Iris CMAC systems.  Features: 1.8mm Standard (160-degree horizontal field of view) Corrosion-Proof 316L Marine Grade Stainless Steel 3MP Hi-Def IP Camera Format IP Version - max. 3MP Hi-Def resolution Super wide angle 160-degree lens IP version supports PoE and 12VDC - ultra-low power Built-in infrared LED illumination (10m range) EN60945, EN55032, EN55035, EN50529 (IP66) , FCC, CE Shock & vibration proof Super rugged and easy to install Applications: Perfect for extreme environments Workboats & tug boats Fishing vessels Engine room monitoring Law enforcement & military Wind farm vessels SUVs, RVs, work vehicles, and trucks Luxury vessels Passenger ferries & cruise liners Specifications: Lens (millimeter): 1.8mm Horizontal Field of View: 160-degree HFOV Sensor (inch): Sensor 1/4” CMOS Sensor Resolution: Variable - 3MP Max (2304 x 1296) Interface: RJ45 10/100 Base T Ethernet Video Processing: H.264 Codec / Dual Stream Protocols/Video Format: TCP/UDP/HTTP/Multicast/UPnP/NTP/RTSP/ONVIF Onvif: Profile S v21.06 Bitrate: VBR / CBR 32kbps 8Mbps Illumination: 6 x 850nm Infra-Red - 10-meter range Lens/Field of View: 1.8mm Standard (160-degree HFOV) Mirroring: Horizontal & Vertical - Configure via Browser Automatic Gain Control: Supported / multiple levels Compatibility: Raymarine / Axiom (LH2 or higher), Simrad / B & G / Lowrance (Latest NOS / NEON OS) / PC-based systems, MFDs with digital (HDMI / DVI) Input, MFDs via IRIS NVR/HVR, IE Browser Operating Temperature: -30 + 60-degrees C Connections: Video: Water Resistant RJ45 Socket / Non-PoE with DC Power Socket Material: Marine Grade 316L Stainless Steel (highly polished as a standard) Power: +12VDC (+10 +15VDC Range) / 1W Nominal / 1.8W Max (LED’s ON) Power Over Ethernet (PoE): IEEE802.3af Weight & Dimensions: 88mm ø x 22.25mm above and below the mounting surface Environmental: EN60529 / IP66 EMC: EN55032:2015/A11:2020 & EN55035:2017/A11:2020 EN60945:2002 Sections 9 & 10 / PoE with Compliant PoE Injector / FCC Part 15 A & B RoHS: EN6300:2018

Dual USB-C Power Socket A dual USB-C Power Socket charges two devices simultaneously. The total output 8A load is split 4A per side as needed. USB-C features Power Delivery (PD) for faster and more flexible charging. Enough power to charge phones, pads, and tablets quickly and efficiently. A protective dust cap extends the life of the charger. Features:  Constructed of injection molded nylon  Installation is as easy as drilling a 1-1/8" hole, inserting the socket body, tightening the locking nut, and connecting the wires  Also, fits Sea-Dog® Power Socket Shell (426100) and Mounting Bracket (426105) Blue LED illumination  IP65 rating  CE and RoHS compliant Specifications: Output DC: 5V/8A Input: 8-32VDC USB-C Watts: 60W@24V  Plug-In Side Diameter: (inch) 1-7/16"     Length: (inch) 2-1/4" *Sold as an Individual

Pow'r Grip LeveLock Double Locking Fish Rod Holder Mount  Just when you thought it couldn't get any better.....this mount adjusts and locks in place at both ends.   We've joined the "LeveLock" Adjustable Fish Rod Holder Mount, with the "Pow'rGrip" Adjustable Fish Rod Holder Mount.  This allows the "Pow'rGrip" portion of the mount to adjust to any size rod holder and lock in place, while the "LeveLock" portion of the mount, adjusts and locks your Magma rectangular grill.  This mount is the strongest, most corrosion resistant, most versatile mount in the industry. Compatible With: Rectangular Grills and Single Mount Tables Technical Specifications: Material - 18-8 Stainless Steel and 356 Anodized Aluminum  Dimensions W x H) - 3-5/8" x 8" (9.3 x 20.3 cm) Weight - 1.77 lb (.81 kg) *Sold as an Individual 

Power Lock Scotty's most popular value-priced, positive-locking, open style rod holder. Fibre reinforced engineering nylon, offers strength, resilience and reliability. No. 231 Power Lock Rod Holder with No. 244 Flush Deck Mount WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

4-In-1 Flush Vertical Surface Mount  - 316L Marine Grade Stainless Steel - Recess Mount Dome Iris’ Sx76 series camera is the first of its kind designed to be installed into a bulkhead or vertical surface. Its waterproof stainless steel case is machined from marine-grade 316L stainless steel, which means it will not corrode in harsh saltwater environments, making it a great option as a backup or docking camera for boats. By mounting the camera on the sides of your boat, it can even be used when mooring alongside jetties or pontoons.  During installation, the camera’s inner ball can be adjusted and locked into position by tightening the outer bezel to achieve the desired view.  For analog or analog hi-def (such as TVI / CVI / AHD) systems, the S076 version features 1080P resolution. The camera also outputs a CVBS signal for legacy composite video systems.  As well as marine applications, the camera's tough case, and small footprint make it a perfect visibility aid for recreational vehicles, fire and rescue trucks, and other applications requiring a robust and reliable high-definition camera. The camera is certified to EN60945, EN55032, EN55035, and EN60529 (IP66) and is ONVIF compliant. For marine applications, the camera is directly compatible with Raymarine LH2 and above, Simrad, Lowrance, and B & G. For Garmin systems, use them in conjunction with Iris CMAC systems. Features: 1.8mm standard lens (160-degree horizontal field of view) Corrosion-Proof 316L Marine Grade Stainless Steel Available in 4-in-1 (CVBS, TVI, CVI, AHD) & IP formats Analogue Hi-Def resolutions up to 1920x1080P resolution IP Version - Max 3MP Hi-Def Resolution Super wide angle 160-degree lens IP version supports PoE and 12VDC - ultra-low power Built-in infrared LED illumination (10m range) EN60945, EN55032, EN55035, EN50529 (IP66) , FCC, CE Shock & vibration proof Super rugged and easy to install Applications: Perfect for extreme environments Workboats & tug boats Fishing vessels Engine room monitoring Law enforcement & military Wind farm vessels SUVs, RVs, work vehicles, and trucks Luxury vessels Passenger ferries & cruise liners Specifications: Lens (millimeter): 1.8mm Horizontal Field of View: 160-degree HFOV Sensor (inch): Sensor 1/4” CMOS Sensor Resolution: CVBS: 960H / AHD, HD-TVI. HD-CVI: 1920 x 1080 Interface: OSD Menu via in-line Joystick in Cable Tail Video Processing: Analogue / Analogue HD Protocols/Video Format: 1VPP / 75Ω composite / AHD/TVI/CVI formats Onvif: NA Bitrate: NA Illumination: 6 x 850nm Infra-Red - 10-meter range Lens/Field of View: 1.8mm Standard (160-degree HFOV) Mirroring: Horizontal & vertical configuration via the OSD  Automatic Gain Control: Supported / multiple levels Compatibility: CVBS: All MFDs / Screens featuring composite video input AHD/TVI/CVI via interface or IRIS CMAC System Operating Temperature: -30 + 60-degrees C Connections: Video: Video - 75Ω BNC female / 2.1mm DC socket Material: Marine Grade 316L Stainless Steel (highly polished as a standard) Power: +12VDC (+10 +15VDC range) / 1W Nominal / 1.8W max. (LEDs on) Power Over Ethernet (PoE): NA Weight & Dimensions: 88mm ø x 22.25mm above and below the mounting surface Environmental: EN60529 / IP66 EMC: EN55032:2015/A11:2020 & EN55035:2017/A11:2020 EN60945:2002 Sections 9 & 10 / FCC Part 15 A & B RoHS: EN6300:2018

Anchor Lock w/ Flush Deck Mount (P/N 244) Anchor release system for small boats in still-water fishing situations.  Features: Easy lock and release action allows anchor line adjustment with only one hand.  For use with rope up to 1/2' diameter.  Tough construction and roller bearing for smooth, quiet operation. Includes No. 244 Flush Mount Bracket Mount Dimensions: 4" x 2" x 2" Bolting Dimensions: 1-15/16" 3-3/16" WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flip Pro with Front Fit Bezel 12/24V Fast Charge Dual USB-A/C Socket Ultra-fast USB charging for the next-generation boater.  Flip Pro is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection and the fastest charging for your device onboard. Ultra-fast USB charging for the next-generation boater.  Flip Pro with a front bezel is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection for any device and the fastest charging for your device onboard. Flip Pro with front bezel was manufactured as an adaption to the original SC-USB-F1 to offer flexibility to installation, as in some cases, it is not possible to gain access to behind panels. Therefore, the front fit bezel provides an alternative route for installation, allowing the option to fit the product from the front using screws. When not in use, the spring-loaded cap remains tightly closed, protecting the ports from the elements. When charging, it quickly locks open to protect your cables when plugged in. Featuring a super compact footprint, Flip Pro is constructed from premium, marine-grade materials. and is IPX4 waterproof, making it completely washdown-ready. Flip Pro is FAST! It will charge at 36W on a 12V system or up to 60W on a 24V system. This makes it perfect for charging modern laptops via the USB-C port. It’s also 2x faster for charging large tablets and is designed to effortlessly charge both an iPad Pro & iPhone at the same time.  The install cut-out matches those of standard USB sockets for easy retrofit or swap of an existing USB charger, allowing you to keep up with the heavier power draws of modern electronic devices. Universal: Universal fit for any USB-A or USB-C connectors. Fast charge (60W max) up to 2 devices at a time. Easy Install, using standard USB mounting hole - 29mm (1 1/8”) Washdown Proof: IPX4 waterproof with the cover closed. Marine Ready: Internal anti-corrosion protective coating UV resistant 316 stainless hinge and spring Electrical Information: Input voltage: 10-30V DC (12/24V System) Input current Max: 6A (10A fuse recommended)  Standby power draw: 0.01W USB – C output:  60W max on 24V system 36W max on 12V system USB – A output:  36W max The charge cable supplied with your device (tablet, phone, action camera, etc) must be used to achieve maximum charge performance from this charger. Phones will charge at the same speed whether on a 12V or 24V input voltage system. However, a 24V system must be used to get the full 60W output suitable for fast-charging laptops.  What is USB-C?  More powerful - Our USB-C has no problems charging even the largest iPad Pro at twice the speed as a USB-A.  More Compact: The slim, oval shape is smaller than USB-A and is also symmetrical and reversible - no more having to flip the cable over to get it into the port! More Flexible: It’s fast becoming the universal connector/charge type on all devices, replacing the USB-A, USB-B, and Micro-USB. New devices are being launched with this charge option only e.g. iPhone 13.

Two Socket Mounting Plate Only - 10 Pack This dual power socket/meter panel accommodates USB and standard power sockets and meters that are 1-1/8 inches in diameter. Constructed of injection-molded nylon.  Specifications: Distance Between Holes (Length): 3-1/2 in. Distance Between Holes (Width): 1 in. Diameter: 1-1/8 in. Weight: 0.05 lb. Package Size: Includes 10 dual power socket/meter panels