Universal Mast Mount Platform for 12"18" Radome Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast. Adjustable Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast. Incredible Strength The solid under body construction not only greatly improves strength but also hides radar cables. On certain models. Accessories Pre-drilled under body allows for flood lights or horns to be mounted on certain models. Compatible Manufacturers: Furuno JRC Koden Lorenz Sitex VDO

Universal 24" Radar Mast Platform Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast. Adjustable Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast. Incredible Strength The solid under body construction not only greatly improves strength but also hides radar cables. On certain models. Accessories Pre-drilled under body allows for flood lights or horns to be mounted on certain models. Compatible Manufacturers: Furuno Garmin JRC Koden KVH Raymarine Simrad Sitex

Universal Masthead Mount Extend your WindTrak 10.Sport or WindTrak 15 vane away from masthead obstructions and turbulence. The 13" (33 cm) arm comes with hardware allowing side or top mounting and offset angles up to ±20 degrees. May be attached securely to flat, curved, vertical, horizontal, or inclined surfaces. Gain space aloft and improve mounting position of wind finders and other equipment. Mount on the back of the mast for easier viewing from the cockpit. The mount adapts to virtually every masthead situation. Features: Length 13" (33 cm) Weight 3.2 oz (90 g) Boom can be shortened if necessary; complete instructions included Can be used with WindTrak Light #3200. Also accommodates Davis J-Base Mounts (using #10 stainless steel screws and nuts, not included)

18" Radar Mast Platform Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast. Adjustable Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast. Incredible Strength The solid under body construction not only greatly improves strength but also hides radar cables. On certain models. Accessories Pre-drilled under body allows for flood lights or horns to be mounted on certain models. Compatible Manufacturers: B&G Garmin Humminbird Lowrance Raymarine SImrad

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

SM-18-A Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast. Adjustable Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast. Incredible Strength The solid under body construction not only greatly improves strength but also hides radar cables. On certain models. Accessories Pre-drilled under body allows for flood lights or horns to be mounted on certain models. Compatible Units: Intellian - i4 & i4P KVH - M5, FB250(18"), TV5  Raymarine - 45STV  Sea Tel/Cobham - ST14, FX150 (16.5")  VDO - Ocean Line 337 

Mast Mount f/KVH TV1 Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.  Adjustable Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast. Incredible Strength The solid under body construction not only greatly improves strength but also hides radar cables. On certain models. Accessories Pre-drilled under body allows for flood lights or horns to be mounted on certain models. Compatible Units: Intellian - 12 & i3 KVH - M1DX, M1, TV1, M2, M3, M3DX, M3ST, V3, V3-IP, TV3, V3HTS and V30 Raymarine - 33STV & 37STV  

Mast Mount for FLIR M300 Series Fits Mast with 2-5/8" or Larger Achieve an unobstructed view for your FLIR or Raymarine thermal camera by mounting it on your mast. Made from marine grade aluminum. We now Chem-Film (same process used by Boeing) each high grade aluminum part prior to our standard 3 part epoxy prime and powder coat to ensure the best possible finish and corrosion resistance. Heavy Duty Six rivets per foot are used to hold the heavy duty mounting feet to the mast. Solid under-body construction not only greatly improves strength but also hides cables.

The Mast Mount is designed to fit multiple specific manufacturers Radomes and Satellite Antennas.  It is constructed from lightweight aluminum and is powder-coasted white for a durable finish.  For fast and accurate installation Edson designed mounting feet that can be properly secure to a wide range of mast profiles. One Mounting Plate is required to complete the Edson Vision SeriesMast Mount System. Features: Rugged Design Marine-grade aluminum construction Powder-coated white Rivets included for mast attachment Easy installation First all modular system - extremely versatile Simple selection and installation Requires Vision Mounting Plate to install radar or sat dome antenna Mast Mount Radar Platform For sailboats and trawlers Swivel Feet fit most masts Rivets included

Camera Mast Mount for FLIR M300 Series Designed in partnership with FlIR ensuring the perfect fit for your camera.  Scanstrut Mast Mounts are the first choice for boat owners the world over. The range has been extended so we now offer an option for installing the latest Thermal cameras onto the yacht's mast. Designed in partnership with FLIR ensuring the perfect fit for your camera. Features: Compact Mounting Marine-grade Aluminium, with unique 4 step marine paint system for long-lasting, premium finish Camera fits safely and snugly close to the mast Universal mast fit Secure install Adjustable mounting feet which fit most mast sizes. The four swivel feet use a 12-point fixing using high quality Monel rivets Includes a Safety Wire Kit that independently attaches camera to mast in case an accident damages the installation

Mast Mounts Compatible Units: Raymarine: 24" 4kW Radome Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts. Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation. Features Easy and quick to install with all fastenings supplied Attached to mast by four swivel feet matching the profile of any mast 12 point fixing using highest quality Monel rivets for a secure installation Nylon washers for all fastenings to protect paint finish Waterproof cable grommet included to seal cable entry into mast Materials Marine grade 6082 aluminium Polyester powder coated for a durable and gloss white finish Kit includes 1 x Mast Mount

Mast Mounts Compatible Units: Raymarine: 2kW Radome Fantom 24 GMR24HD / 24xHD Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts. Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation. Features Easy and quick to install with all fastenings supplied Attached to mast by four swivel feet matching the profile of any mast 12 point fixing using highest quality Monel rivets for a secure installation Nylon washers for all fastenings to protect paint finish Waterproof cable grommet included to seal cable entry into mast Materials Marine grade 6082 aluminium Polyester powder coated for a durable and gloss white finish Kit includes 1 x Mast Mount 4 x Swivel mounting feet 1 x Complete fastening pack

Mast Mounts Compatible Units: Furuno 1734/1832/1834/DRS4D/NavNet GMR24HD Interphase RE-8/RE-9 Koden 4kW 20"/4kW (RB715A) Lowrance LRA2400 HD (w/ 19042 Adaptor) Northstar 24" (M Series/8000i) (w/ 19042 Adaptor) Simrad 24" (GB40/NX40/45) (w/ 19042 Adaptor) Simrad 24" (DX60) w/ 19042 Adaptor) Sitex MDS-9/Radarpc-4D Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts. Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation. Features Easy and quick to install with all fastenings supplied Attached to mast by four swivel feet matching the profile of any mast 12 point fixing using highest quality Monel rivets for a secure installation Nylon washers for all fastenings to protect paint finish Waterproof cable grommet included to seal cable entry into mast Materials Marine grade 6082 aluminum Polyester powder coated for a durable and gloss white finish Kit includes 1 x Mast Mount 4 x Swivel mounting feet 1 x Complete fastening pack