|
Starlink Maritime Black Top Plate for Seaview M1 & M2 Style Modular Mounts
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "Swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Features:
Starlink Wedge Base hole pattern pre-dimpled in this modular top plate
Water-tight gasket in the center of the plate to pass the Starlink cable
The 1” thick starboard plate can accommodate a Seaview light bar
|
168.00 |
|
|
Starlink Maritime Top Plate for Seaview M1 & M2 Style Modular Mounts
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Features:
Starlink Wedge Base hole pattern pre-dimpled in this modular top plate
Water-tight gasket in the center of the plate to pass the Starlink cable
The 1” thick starboard plate can accommodate a Seaview light bar
|
168.00 |
|
|
Starlink Maritime Top Plate for Seaview M1 Style Modular Mounts
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Features:
Water-tight gasket in the center of the plate to pass the Starlink cable
Predrilled and all hardware needed to mount the Starlink is included
*Not light bar compatible
|
163.20 |
|
|
Starlink Maritime Top Plate for Seaview M1 Style Modular Mounts - Black
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "Swiss Cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Features:
Water-tight gasket in the center of the plate to pass the Starlink cable
Predrilled and all hardware needed to mount the Starlink is included
*Not light bar compatible
|
163.20 |
|
|
23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1512.00 |
|
|
13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1032.00 |
|
|
28" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Seperately
|
2078.40 |
|
|
WD-RAD-01 Top Plate f/PowerTower® Radar Mounts - 4°
Enhance the performance of your radome with the rugged, marine-grade, UV stable wedge that angles the radar down 4° below horizontal to provide a level horizon for your radar when the boat is underway.
Mounts between PowerTower® mount and base of radar.
Compatible with:
Garmin - Fantom 18, 24, GMR18HD / 18xHD / 18HD+, GMR24HD / 24xHD, GMR40 radars
Humminbird - AS 21RD4KW, HB 2124 CHIRP radars
Lowrance - HALO20, HALO20+, HALO24, LRA-1800 / RB714A / DX42, LRA-2400 HD radars
Raymarine - QUANTUM (Q24C), QUANTUM 2 (Q24D), RD218, RD418/RD418HD, RD424/RD424HD radars
Simrad - DX45, DX60 / DX64-S, GB40 / NX40/45 / NSE8/12, GB40 / NX40/45 / NSE8/12 / RB712A / DX42S, GB40 / NX40/45 / NSE8/12 DX64S radars
Sitex - MDS-12 radar
Features:
Enhance the performance of your radome with the Universal Scanstrut 4° radar base wedge
4° Base Wedge for mounting under PowerTower®
A rugged, marine-grade, UV stable wedge
Compatible with radomes from most radar manufacturers
Technical Specifications:
Material - Marine Grade Polymer
Dimensions (L x W ) - 11.10" x 9.09"
Angle - 4°
In the Box:
Wedge
Base seal
Instruction manual
*Sold as an Individual
|
134.33 |
|
|
ROKK Midi Top Plate f/Garmin and Raymarine
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-502 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (diameter) - 2.11" (53.8 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
ROKK Midi Top Plate f/Raymarine, Lowrance and B & G
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-504 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (L x W) - 5.67" x 2.43" (144 x 61.75 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
ROKK Midi Top Plate f/Humminbird and Raymarine
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-506 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (L x W) - 5.35" x 1.89" (136 x 48 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
ROKK Midi Top Plate f/Garmin, Simrad and B & G
A multi-position, fully adjustable mount for small electronic devices. Install fish finders, chartplotters and other electronics on the dashboard, navigation station and various other desired locations.
The RL-507 is one (1) part of a system based around 4 different heavy-duty anodized aluminum mounts that allow your device to attach to the ROKK Midi to unlock its incredible features.
Features:
Engineered to withstand high shock loading.
Device-specific top plate
Technical Specifications:
Material - ASA Plastic
Dimensions (L x W) - 6.61" x 2.59" (168 x 65.7 mm)
Compatible with the following products
*Sold as an Individual
|
14.11 |
|
|
TP325 Top Plate f/Converting Merriman/Yacht Specialties Steering Systems to 12" Wide 1.25" Diameter AngelGuard
12" Top Plates are used for upgrading from an existing 1" diameter pedestal guard to a 1.25" StraightGuard or AngleGuard. Specifically designed for Converting Merriman or Yacht Specialties steering systems.
12" Top Plates Include:
316 Stainless Steel
Mirror Polished Finish
Precision Laser Cut
|
191.99 |
|
|
Starlink Modular Top Plate with Starlink Stainless Steel 1"-14 Threaded Adapter & Stainless Steel Base
Starlink quick-release top plate for Seaview "M1" and "M2" style mounts.
Features:
316L stainless steel Starlink adapter with a 1"-14 threaded fixed base on ¼” aluminum plate
The top of the adapter is machined to fit the Starlink antenna post
The adapter with the fixed base and modular plate is 4 1/4” tall
The ¼” aluminum plate is powder-coated white and can accommodate a Seaview light bar
|
288.00 |
|
|
ADAF3 Modular Top Plate for FLIR M300 Series Thermal Cameras f/Mounts Ending in M1 or M2
Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.
Unique Design
No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics.
Note: This only applies to the ADA-R1, ADA-S1 & ADA-S2 Top Plates
King Starboard
The ADA-R2, ADA-S3, ADA-S4 & ADA-F1 Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.
|
192.00 |
|