TCD2042 Thruster Joystick Control The traditional TCD/WCD/TSC controls have been renewed. The updated design matches the style of the QNC Quick Nautical Control commands, which feature a glossy black tempered glass panel. The TCD/WCD/TSC controls differ from the QNC range in the choice of materials they feature a special and scratch-resistant glossy Lexan instead of the tempered glass. The fixing method is different as well: the traditional screws have been replaced by a special 3M VHB double-sided gasket, which allows for faster installation. The technical and operating characteristics of the TCD, WCD, and TSC controls are identical to those of the previous models. Features: A special 3M VHB double-sided gasket that allows for a faster installation Made of scratch-resistant glossy Lexan

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Thruster Joystick Panel Controller Control your Lewmar bow thruster using the joystick panel. Compatible with: Lewmar 110TT Lewmar 140TT Features: Plug 'n' Play connection from joystick to Thruster means dual station control is possible On/Off illumination Easy installation connection *Sold as an Individual

JCU-1 Joystick Control Unit & Poe Injector Kit The M-Series controller is simple to use, provides precise system control, and lets users access all of the important camera functions with push-button controls. Controller Functions: Heated LCD screen - Instantly displays system status User-programmable "hot key" for commonly used functions Scene selection allows the operator to optimize the system's performance for specific situations - Night Running, Day Running, Night Docking, and Man Overboard User-selectable color palettes change the video display mode for easier viewing based on operator preference User-programmable Home button allows the operator to point the pan/tilt camera to pre-defined positions with the push of a button Precision proportional pointing control is provided through a custom, sealed, 8-way iDrive style control knob Backlit for easy nighttime readability; the sealed buttons are easy to see and provide positive tactile feedback The controller is fully sealed for survival in a maritime environment, and meets IPx6 standards Install as many control stations around your vessel as you want, thanks to the system's easy Ethernet connectivity Power Over Ethernet Injector - 12V FLIR's 12V Power Over Ethernet Injector is a key component in connecting your FLIR maritime thermal imaging camera to an Ethernet-equipped Joystick Control Unit.

JCU-1 Joystick Control Unit for M-Series - RJ45 Connection The M-Series controller is simple to use, provides precise system control, and lets users access all of the important camera functions with push-button controls. Controller Functions: Heated LCD screen - Instantly displays system status User-programmable "hot key" for commonly used functions Scene selection allows the operator to optimize the system's performance for specific situations - Night Running, Day Running, Night Docking, and Man Overboard User-selectable color palettes change the video display mode for easier viewing based on operator preference User-programmable Home button allows the operator to point the pan/tilt camera to pre-defined positions with the push of a button Precision proportional pointing control is provided through a custom, sealed, 8-way iDrive style control knob Backlit for easy nighttime readability; the sealed buttons are easy to see and provide positive tactile feedback The controller is fully sealed for survival in a maritime environment, and meets IPx6 standards Install as many control stations around your vessel as you want, thanks to the system's easy Ethernet connectivity

Weather Cover for Joystick Control Unit FLIR's Joystick Control Unit Weather cover is a protective covering for the Joystick Control Unit of your maritime thermal imaging camera. It is designed to protect your Joystick Control Unit (JCU) from the dangers of the open ocean. Built specifically for marine use, JCU Weather Cover has been designed by FLIR to guard against salty spray, moisture, and other irritants that could potentially damage your thermal camera's Joystick Control Unit. You should always put this thermal imaging accessory on your JCU when it is not in use to prevent possible damage. Keep it operating smoothly by using the FLIR Weather Cover. Features: Protective covering Protects the electronics of your Joystick Control Unit (JCU) Guards against moisture, salt and other irritants found in marine environments

JCU-2 Joystick Control Unit & POE Injector Kit JCU-2 Joystick Control Unit The joystick is the primary control for the M400 & M400XR and the new M300 series (M300C, M332, M364, M364C, and M364C LR. It is used to wake the system or put it in standby, operate the pan and tilt movement, zoom the camera, control cameras modes and features, and configure system settings by means of OSD menus. Includes  Joystick Control Unit (JCU2) Mounting hardware Power Over Ethernet Injector - 12V FLIR's 12V Power Over Ethernet Injector is a key component in connecting your FLIR maritime thermal imaging camera to an Ethernet-equipped Joystick Control Unit. Includes: JCU-2 keypad Keypad mat Mounting gasket 4 x mounting screws, rubber washers, mounting clamps Cable gland nut RJ45-to-RJ45 Ethernet cable, 7.6 m (25 ft) Documentation pack  POE injector

JCU-2 Joystick Controller The joystick is the primary control for the M400 & M400XR and the M300 series (M300C, M332, M364, M364C, and M364C LR. It is used to wake the system or put it in standby, operate the pan and tilt movement, zoom the camera, control cameras modes and features, and configure system settings by means of OSD menus. Includes:  Includes: JCU-2 keypad Keypad mat Mounting gasket 4 x mounting screws, rubber washers, mounting clamps Cable gland nut RJ45-to-RJ45 Ethernet cable, 7.6 m (25 ft) Documentation pack 

MD-324 Thermal Night Vision Camera with Joystick Control Unit This affordable, fixed-mount thermal night vision system helps with steering around obstacles, collision avoidance and finding people in the water at night. Simple to mount and easy to integrate into your existing electronics, MD-Series' display can be mounted separately on your dashboard, or the feed can be integrated into an existing display to save space. Now even small boats can see clearly at night with the MD-Series Fixed Mount Thermal Night Vision Camera from FLIR. The MD-324 features a 320 x 240 pixel thermal imager with a wide angle 19mm lens, a 2X digital zoom allowing you to magnify distant targets for enhanced viewing and identification & 30Hz refresh for smooth, clear images. The MD-Series delivers stunning detail and clarity day or night thanks to its state-of-the-art FLIR thermal imaging technology. The camera can easily detect floating objects, navigation aids, other vessels, and even people in the water with ease. Engineered for smaller cruising, fishing and sailing vessels, MD-Series is both compact and lightweight. The camera measures 5.9" in diameter and just 7" high. The small footprint allows the camera to easily mount on any T-top, cabin roof, radar arch or mast. Features: Available in 320 x 240 2x e-zoom standard Ethernet-enabled for simple integration into your current electronics Slim profile (7" high and only 3 pounds) makes for an unobtrusive mount *Comes with a Joystick Control Unit

MD-625 Static Thermal Night Vision Camera with Joystick Control Unit This affordable, fixed-mount thermal night vision system helps with steering around obstacles, collision avoidance and finding people in the water at night. Simple to mount and easy to integrate into your existing electronics, MD-Series' display can be mounted separately on your dashboard, or the feed can be integrated into an existing display to save space. Now even small boats can see clearly at night with the MD-Series Fixed Mount Thermal Night Vision Camera from FLIR. Fast-moving crafts will appreciate the enhanced long-range performance of the MD-625 camera with a high-resolution 640 x 480 thermal imager and 25mm lens. The MD-625 has a 2X and 4X digital zoom for enlarging distant targets & 30 Hz refresh for smooth, clear images. The MD-Series delivers stunning detail and clarity day or night thanks to its state-of-the-art FLIR thermal imaging technology. The camera can easily detect floating objects, navigation aids, other vessels, and even people in the water with ease. Engineered for smaller cruising, fishing and sailing vessels, MD-Series is both compact and lightweight. The camera measures 5.9" in diameter and just 7" high. The small footprint allows the camera to easily mount on any T-top, cabin roof, radar arch or mast. Features: 640 x 480 resolution 4x e-zoom Ethernet-enabled for simple integration into your current electronics Slim profile (7" high and only three pounds) makes for an unobtrusive mount *Comes with a Joystick Control Unit

Replacement Joystick Control for 22200 and 22201 M-100 Halogen Spotlights The replacement joystick control is for specific use with the 22200 and 22201 M-100 spotlights. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Boat Outfitting Equipment and Supplies When it comes time for outfitting your boat, you can get all your boating supplies and boating accessories from us. You will never need to go anywhere else for your boat outfitting, because we have all the boat supplies you need. If you're looking for anchors/chain/rope, anodes, antifouling systems or boarding ladders, we have you covered. We can also offer you a selection of bottom paint and bow thrusters to choose from. You may also want cleaning supplies that offer deck/galley options so you can get your boat sparkling and ready to enjoy. We also have display mounts and docking accessories to complete your outfitting needs.

Double Can Proportional Thruster Panel Joystick The multi-axial DBPPJA joystick can be used to operate the thrusters either individually or simultaneously. Rotating the joystick will operate them in opposite directions to rotate the boat on its axis. Featuring a lock-and-hold function, the new panel makes docking the simplest of operations. This double control panel features a modern-design waterproof housing complemented by a classy aluminum bezel to integrate flawlessly into every helm position. Features: For BOW PRO (Boosted) thruster only Controls both bow and stern thruster Unique twist function to rotate the boat Proportional control The compact design fits in the cut-out of a single-thruster joystick Lock and-hold function for easy docking LED indication feedback Modern styling V-CAN compliant Waterproof housing (IP65) Dock safely, surely, and with confidence Specifications: Child Protection: Yes Voltage (V): 12 Purpose: Thruster control Sort Control: Joystick Proportional Control: Yes V-CAN: Yes Build-In Depth: 120 mm Bezel: Aluminium Function: 0 Width: 85 mm Cut-Out Diameter: 76 mm Height: 85 mm This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Joystick with Hold VETUS Bow Pro Proportional Joystick control panel. Features: Compact design and high quality materials Safe and easy proportional control over your vessel Aluminium bezel Quick installation in Ø 75 mm cut-out hole Waterproof housing IP65 V-CAN CANBUS protocol compliant Twin connector for multiple stations Status indication With thruster hold and lock function Designed for use with the VETUS Bow Pro thrusters only - not suitable for standard DC Thrusters. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Bow Thruster BTQ 110-25 25KGF - 12V - D110 - 1.3kW Better Performances, Lower Absorption The 4-blade Propellers guarantee maximum thrust performance and reduction in current absorption. They are made of composite materials, resistant in every condition. The counter-rotating system offers better thrust performances. The two props have been designed to suit left side and right side, to guarantee the same upper performances in both directions. Features: The Gearbox is created so that the behavior of the propeller is unaffected in either direction. The bronze propeller gearleg is provided with a hydrodynamic profile that minimizes turbulence. Maintenance is not required since the special highly resistant components guarantee a perfect lubrication seal for life. The anodic aluminum protection is easily replaceable. In case of total corrosion of the anode, the prop doesn’t get lost because it’s fixed directly to the pod, independently from the anode. The elastic joint that optimizes the alignment between motor and gearbox is an exclusive Quick design. This acts as an even tension device, preserving the operating system from impulses from the bow thruster, with above-average results. The Motors New-generation materials have been chosen to constantly guarantee required output and maximum performance, given the severe conditions required by the application. Top Safety In case of relays’ melting, the TMS remote circuit breaker system switch-off the power to the motor from any place where a TDC panels or a TSC emergency mushroom panels are installed. Motor temperature sensor BTQ motors don’t need the thermic sensor to be able to always provide the maximum power when needed. The overheating protection is controlled by the software inside the touch panel or the joystick panel.