NT-Evolution Security Hard Wired Package with OB Cowling Sensor GOST gives users the power to know the location of the boat and whether it's safe, secure, and ready to enjoy. Affordable, easy to install, and simple to use, GOST is the perfect solution for connecting boaters with the vessel. Features: Top-of-the-line, globally capable wired security, monitoring, and satellite tracking system designed specifically for harsh marine environments Real-time GPS location tracking GOST IDP 100x message size capacity What's Included DOOR / HATCH / ENG. COWLING | GDC - EXT - WGHD  Is the GOST standard door and hatch contact used inside the vessel? It is also used for engine cowlings.  Beam Sensor | GNT IBS 1 Is an infrared beam sensor designed to protect the exterior perimeter of the vessel. When the beam between the emitter and receiver is broken, the siren will alarm. High Water Sensor| GMM HWS Includes the bracket and the float switch that will be installed in the bilge of the vessel slightly below the vessel factory-installed high water sensor. Remote Keyfob | GMM KF2 Compact water-resistant design with a backlight for buttons and auditory feedback for arming or disarming a security system. The keyfob performs up to 6 actions per remote control, with a range of up to 150 feet. Water Resistant Strobe | GA STROBE WHITE Ultra small, self-contained semi-hemispheric white LED lights Surface or internal mount featuring 25 scan lock flash patterns, including synchronize feature for alternating or synchronous flashing. Mini Siren | GA-MINI-SIREN GOST Acoustics mini water-resistant, super-loud multi-tone marine siren, 125 db, 20 watt. Wired Sensors | Zone Hatch | Z2 (NC) Beam-Seansor | Z3 (NC) Engine Cowling | Z4 (NC) High Water | Z5 (NO) ComBUS | Four-Wire

NT-Evolution Security Hard Wired Package GOST gives users the power to know the location of the boat and whether it's safe, secure, and ready to enjoy. Affordable, easy to install, and simple to use, GOST is the perfect solution for connecting boaters with the vessel. Features: Top-of-the-line, globally capable wired security, monitoring, and satellite tracking system designed specifically for harsh marine environments Real-time GPS location tracking GOST IDP 100x message size capacity  What's Included 110 AC Power Out | GNT IP68 110AC POWEROUT HW Waterproof, 110 AC monitoring of vessel shore power. Door/Hatch | GDC EXT WGHD Water-resistant door and hatch contact are used to secure vessel access points. Beam Sensor | GNT IBS 1 Is an infrared beam sensor designed to protect the exterior perimeter of the vessel. When the beam between the emitter and receiver is broken, the siren will alarm. High Water Sensor| GMM HWS Includes the bracket and the float switch that will be installed in the bilge of the vessel slightly below the vessel factory-installed high water sensor. Remote Keyfob | GMM KF2 Compact water-resistant design with a backlight for buttons and auditory feedback for arming or disarming a security system. The keyfob performs up to 6 actions per remote control, with a range of up to 150 feet. Water Resistant Strobe | GA STROBE WHITE Ultra small, self-contained semi-hemispheric white LED lights Surface or internal mount featuring 25 scan lock flash patterns, including synchronize feature for alternating or synchronous flashing. Mini Siren | GA-MINI-SIREN GOST Acoustics mini water-resistant, super-loud multi-tone marine siren, 125 db, 20 watt. Wired Sensors | Zone: Hatch | Z2 (NC) Beam-Sensor | Z3 (NC) 110 AC Power Out | Z4 (NC) High Water | Z5 (NO) ComBUS | Four-Wire This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Evolution™ F Series 1200W, 120V Pure Sine Inverter/Charger with 12V Input & 60 Amp Charger with Hard Wiring Pure sine wave inverter/charger with 6 programmable charging profiles – 2, 3 and 4 stages with Equalization. For use with Lead Acid or Lithium Batteries. Samlex Evolution™ Series inverter/chargers provide reliable AC power wherever it’s needed. For use with boats, RVs, cabins and specialty vehicles, as well as alternative energy, back-up and emergency power applications. Adaptive Battery Charger Option for Lead Acid Batteries 6 programmable charging profiles – 2, 3 and 4 stages with Equalization Algorithm monitoring in the Bulk Stage assesses the battery’s condition. The remaining charging stages are based on the battery’s condition rather than a pre-set charging time. Reduces excess charging time and extends life of battery Transfer Switch Zero transfer time when switching from Inverter to AC input source. When AC input source comes on, the inverter synchronizes with the incoming wave form and then transfers instantly at zero crossing without interruption to the load. Surge Capacity (Active Power Boost) The inverter has a surge capability of 3X its continuous power rating, allowing it to turn on loads with high starting surge. Inverter loads can exceed the continuous power output by the Power Boost Allowances without triggering and overload fault. There is no need to upsize to a larger inverter/charger to handle a heavy surge load, resulting in reduced costs. Solar Input Connect a solar charge controller (up to 50A) directly to the EVO™ though the Battery Charger External DC Input External charging current is monitored to free up more power from the grid to be available to the load while charging. ONLINE Mode can be used to prioritize Batteries/Inverter over the grid, ideal for those who want to operate primarily on solar power, even when the grid is available (when grid is costly). State-of-the-Art Technology Multiple physical points of protection monitoring are scanned up to 10,000 times per second to detect adverse internal and external conditions. The EVO™ is practically indestructible. The EVOTM will detect fault conditions and initiate a healthy shutdown before any damage can be done. AC Input/Output Option AC Power Cord Inlet and Duplex GFCI outlet: EVO-1212F/1224F; hardwired: EVO-1212F-HW/1224F-HW The EVO-RC-PLUS remote control (sold separately) can be used to capture detailed EVOTM performance data, stored on a removable 16GB SD Card. Advanced features for programming various parameters and modes of operation. 4 rows of 20 character alpha numeric LCD display for messaging. The EVO™ uses five temperature sensors placed throughout the unit to determine operation of 2 speed controlled cooling fans. Reduces unnecessary fan noise and energy consumption by only running when and where the fans are needed. Applications: Boats, RVs, trucks, specialty vehicles Alternative energy, off-grid, cabins, remote locations, areas with unreliable utility power Back-up and emergency power applications ABYC Compliant  WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Evolution™ F Series 1200W, 120V Pure Sine Wave Inverter/Charger with 24V Input & 40 Amp Charger with Hard Wiring Pure sine wave inverter/charger with 6 programmable charging profiles – 2, 3 and 4 stages with Equalization. For use with Lead Acid or Lithium Batteries. Samlex Evolution™ Series inverter/chargers provide reliable AC power wherever it’s needed. For use with boats, RVs, cabins and specialty vehicles, as well as alternative energy, back-up and emergency power applications. Adaptive Battery Charger Option for Lead Acid Batteries 6 programmable charging profiles – 2, 3 and 4 stages with Equalization Algorithm monitoring in the Bulk Stage assesses the battery’s condition. The remaining charging stages are based on the battery’s condition rather than a pre-set charging time. Reduces excess charging time and extends life of battery Transfer Switch Zero transfer time when switching from Inverter to AC input source. When AC input source comes on, the inverter synchronizes with the incoming wave form and then transfers instantly at zero crossing without interruption to the load. Surge Capacity (Active Power Boost) The inverter has a surge capability of 3X its continuous power rating, allowing it to turn on loads with high starting surge. Inverter loads can exceed the continuous power output by the Power Boost Allowances without triggering and overload fault. There is no need to upsize to a larger inverter/charger to handle a heavy surge load, resulting in reduced costs. Solar Input Connect a solar charge controller (up to 50A) directly to the EVO™ though the Battery Charger External DC Input External charging current is monitored to free up more power from the grid to be available to the load while charging. ONLINE Mode can be used to prioritize Batteries/Inverter over the grid, ideal for those who want to operate primarily on solar power, even when the grid is available (when grid is costly). State-of-the-Art Technology Multiple physical points of protection monitoring are scanned up to 10,000 times per second to detect adverse internal and external conditions. The EVO™ is practically indestructible. The EVO™ will detect fault conditions and initiate a healthy shutdown before any damage can be done. AC Input / Output Option AC Power Cord Inlet and Duplex GFCI outlet: EVO-1212F/1224F; hardwired: EVO-1212F-HW/1224F-HW The EVO-RC-PLUS remote control (sold separately) can be used to capture detailed EVOTM performance data, stored on a removable 16GB SD Card. Advanced features for programming various parameters and modes of operation. 4 rows of 20 character alpha numeric LCD display for messaging. The EVO™ uses five temperature sensors placed throughout the unit to determine operation of 2 speed controlled cooling fans. Reduces unnecessary fan noise and energy consumption by only running when and where the fans are needed. Applications: Boats, RVs, trucks, specialty vehicles Alternative energy, off-grid, cabins, remote locations, areas with unreliable utility power Back-up and emergency power applications WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

On-Board Charger Inlet Great for Bass Boats! The Marinco On-Board Charger Inlet makes battery charging through an on-board battery charger safer and more convenient. The inlet mounts on the boat's exterior and is hard wired directly to the charger. Just open the flip lid cover and plug an extension cord into the inlet to bring charging power to the boat's batteries. All of the hatches remain closed and locked throughout the charging cycle, adding convenience and security for the boater. Features: 15Amp 125V straight blade inlet Low profile cap won't catch fishing line Mounts easily to fiberglass and aluminum hulls Perma-Lock™ terminals and color coded wire entrance holes make wiring a snap UV resistant housing/cap Color: Black WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thread-Lock™ Electrified Oval Table Package with LED Lights & USB Ports Package Includes: Thread-Lock™ Electric 3-Piece Package 2 RGB LED Lights x 2 USB 3.0/USB-C Combo Ports LED Remote Controller - change the colors, brightness, and pattern of the LEDs White oval table top 30″W x 18″H with 2 cup holders Features: Available in single-pack quantities complete in retail box Requires 12-volt hard wire into a vessel with a 5 Amp fuse 5-Year Warranty

Wired Bridge Remote Power: 12 or 24 Volt (Hard Wired) Current draw (idle / in use):negligible Dimensions: 3.5"W x 2.25"H x .75"D (88 x 57 x 19 mm) Weight:2.12 oz (60g) Housing material: UV resistant PC/ASA Button material: Silicone (glow in the dark) Operating temp range: 5°F - 113°F (-15°C - 45°C) IP Rating: IP54 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stryker ST Series Permanent Mount White 12V LED with Hard Wired Dash Mount Remote Features: Multiple Unit Selector Function - Allows for independent control of 2 units with 1 remote Home Position Function - On-Command return to 0° home Technology Benefits - Simultaneous Pan + Tilt - Multiple users can operate lights in close proximity without interference Smart Programming Logic - Quick and simple pairing without dipswitches Fluorescent Remote Buttons UV and Saltwater Resistant Stainless Steel Mounting Brackets (perm mount) 5 Year Limited Warranty LED Models: 410,000 Candela, 4,200 Max Beam Distance Max Current Draw: 3.5A @ 13.8V Recommended Fuse: 5A

Stryker ST Series Permanent Mount Black 12V LED with Hard Wired Dash Mount Remote Features: Multiple Unit Selector Function - Allows for independent control of 2 units with 1 remote Home Position Function - On-Command return to 0° home Technology Benefits - Simultaneous Pan + Tilt - Multiple users can operate lights in close proximity without interference Smart Programming Logic - Quick and simple pairing without dipswitches Fluorescent Remote Buttons UV and Saltwater Resistant Stainless Steel Mounting Brackets (perm mount) 5 Year Limited Warranty LED Models: 410,000 Candela, 4,200 Max Beam Distance Max Current Draw: 3.5A @ 13.8V Recommended Fuse: 5A

Radioray GT Series Permanent Mount - White Halogen - Hard Wired Dash Mount Remote The GT series is the culmination of our dedication to continual improvement. The GT series incorporates all of the features that have made Golight the industry standard in remote control lighting, but incorporates upgrades that enhance the lamp’s durability as well as the overall user experience.  GT SERIES UPGRADES: Updated exterior housing design Higher torque drivetrain and more precise pan / tilt control  Increased Ingress protection from dust/water (IP56)  Permanent mount models boast a robust 14 gauge stainless steel mounting bracket Portable magnetic models have 2X magnetic grip Enhanced resistance levels associated with shock, vibration, and impact 10 High Flux LED’s GT SERIES FEATURES: Wireless or Hardwired Remote Control Options Permanent or Portable Mounting Options Halogen or LED Light Head 370° Rotation x 135° Tilt UV Ray and Saltwater Resistant 3 Year Limited Warranty

Radioray GT Series Permanent Mount - White LED - Hard Wired Dash Mount Remote The GT series is the culmination of our dedication to continual improvement. The GT series incorporates all of the features that have made Golight the industry standard in remote control lighting, but incorporates upgrades that enhance the lamp’s durability as well as the overall user experience.  GT SERIES UPGRADES: Updated exterior housing design Higher torque drivetrain and more precise pan / tilt control  Increased Ingress protection from dust/water (IP56)  Permanent mount models boast a robust 14 gauge stainless steel mounting bracket Portable magnetic models have 2X magnetic grip Enhanced resistance levels associated with shock, vibration, and impact 10 High Flux LED’s GT SERIES FEATURES: Wireless or Hardwired Remote Control Options Permanent or Portable Mounting Options Halogen or LED Light Head 370° Rotation x 135° Tilt UV Ray and Saltwater Resistant 3 Year Limited Warranty

Stryker ST Series Permanent Mount Chrome 12V LED with Hard Wired Dash Mount Remote Features: Multiple Unit Selector Function - Allows for independent control of 2 units with 1 remote Home Position Function - On-Command return to 0° home Technology Benefits - Simultaneous Pan + Tilt - Multiple users can operate lights in close proximity without interference Smart Programming Logic - Quick and simple pairing without dipswitches Fluorescent Remote Buttons UV and Saltwater Resistant Stainless Steel Mounting Brackets (perm mount) 5 Year Limited Warranty LED Models: 410,000 Candela, 4,200 Max Beam Distance Max Current Draw: 3.5A @ 13.8V Recommended Fuse: 5A

Stryker ST Series Permanent Mount White 12V Halogen with Hard Wired Dash Mount Remote Features: Multiple Unit Selector Function - Allows for independent control of 2 units with 1 remote Home Position Function - On-Command return to 0° home Technology Benefits - Simultaneous Pan + Tilt - Multiple users can operate lights in close proximity without interference Smart Programming Logic - Quick and simple pairing without dipswitches Fluorescent Remote Buttons UV and Saltwater Resistant Stainless Steel Mounting Brackets (perm mount) 5 Year Limited Warranty Halogen Models: 200,000 Candela, 2,933 ft Max Beam Distance Max Current Draw: 5.5A @ 13.8V Recommended Fuse: 7.5A to 10A

Stryker ST Series Permanent Mount Black 12V Halogen with Hard Wired Dash Mount Remote Features: Multiple Unit Selector Function - Allows for independent control of 2 units with 1 remote Home Position Function - On-Command return to 0° home Technology Benefits - Simultaneous Pan + Tilt - Multiple users can operate lights in close proximity without interference Smart Programming Logic - Quick and simple pairing without dipswitches Fluorescent Remote Buttons UV and Saltwater Resistant Stainless Steel Mounting Brackets (perm mount) 5 Year Limited Warranty Halogen Models: 200,000 Candela, 2,933 ft Max Beam Distance Max Current Draw: 5.5A @ 13.8V Recommended Fuse: 7.5A to 10A