KingPin Seat Mount - Bracket Only A spring-loaded mounting bracket with a 5-1/4" hole pattern for any King Pin post.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

KingPin™ 7" x 7" Seat Mount with Spring - Polished Features: Unintentional Detachment To Comply With ABYC Polished Passivated Swivels Are Stainless Steel Fits Bolt Pattern 4.5″ x 5.5″ Square, Rotates 360º Use With Any KingPin™ Post (sold separately) Patented Design For Optimal Strength

KingPin™ 7" x 7" Seat Mount with Spring - E-Coat Finish Features: Unintentional Detachment To Comply With ABYC Polished Passivated Swivels Are Stainless Steel Fits Bolt Pattern 4.5″ x 5.5″ Square, Rotates 360º Use With Any KingPin™ Post (sold separately) Patented Design For Optimal Strength

KingPin™ 7" x 7" Seat Mount without Spring - E-Coat Finish Features: Unintentional Detachment To Comply With ABYC 7″ x 7″ Swivel No Spring, Rotates 360° Use With Any Thread-Lock™ Fixed Height Post For Fishing Use Only (sold separately)

Seat Mount Spider - Fits 2-3/8" Post This pedestal mount is fitted for 2-3/8" diameter pedestal posts. Features: Seat spider mount with adjustment knob and locking paddle handle Cast aluminum mount construction with injection-molded plastic handle 360° rotation with a locking knob A standard 5-1/4" hole pattern fits virtually all marine seat brands Class AD certified per ABYC standards

ShadeFin Mini Swivel Seat Mount Easily incorporate shade into your boating lifestyle with the ShadeFin Mini Swivel Seat Mount. Available in a kit, the Swivel Seat Mount is also sold separately. This mount is universally designed to fit most boat swivel seats on the market. Simply remove the boat seat from its pedestal, affix the mount on top of the pedestal where all four screw holes are visible, and then reattach the seat, keeping the mount between the seat and the pedestal. The Swivel Seat Mount enables fully adjustable and personalized boat shade for bass boats, skiffs, flats boats, or any boat that utilizes a swivel seat for fishing and fun. Features and Benefits: Constructed out of aluminum-grade 6061 alloys Fits standard 4-screw swivel boat seats Includes an injection-molded nylon cap 3-year limited warranty Specifications: Finish: Powder coated, misty silver          

ShadeFin Mini with White Fabric - Bag & Swivel Seat Mount Kit ShadeFin Mini provides boaters, anglers, and families with portable, convenient, and easy-to-use shade with virtually unlimited angle adjustment. With a variety of mounting options, ShadeFin Mini is simple to set up wherever you need extra protection from the sun. Shade for Any Boat  ShadeFin Mini is ideal for bass boats, flats boats, bay boats, kayaks, pontoons, skiffs, and any boat with limited-to-no coverage from the sun. Its versatile design and hearty construction ensure reliable, hassle-free shade protection that can withstand the harsh marine environment. Features & Benefits Comes with a bag and a swivel seat mount  Light, compact, and portable Virtually unlimited angle adjustment Height adjusts from 36 to 52 in. Can be "clustered" with multiple ShadeFin Minis to cover a large area Sold separately, mounting options include a clamp mount, rod holder mount, deck mount, semi-flush mount, and side wall mount 60" x 38" coverage area  Reduces to 38" x 6" x 5" when not deployed Constructed of durable, UV-, corrosion-, and mildew-resistant materials Features powder-coated aluminum frame with injection-molded nylon components and stainless steel fasteners Fabric is high-quality WeatherMAX 3D  UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts 3-year limited warranty Specifications: Fabric Color: White Mount: Swivel seat    

ShadeFin Mini with Black Fabric - Bag & Swivel Seat Mount Kit ShadeFin Mini provides boaters, anglers, and families with portable, convenient, and easy-to-use shade with virtually unlimited angle adjustment. With a variety of mounting options, ShadeFin Mini is simple to set up wherever you need extra protection from the sun. Shade for Any Boat  ShadeFin Mini is ideal for bass boats, flats boats, bay boats, kayaks, pontoons, skiffs, and any boat with limited-to-no coverage from the sun. Its versatile design and hearty construction ensure reliable, hassle-free shade protection that can withstand the harsh marine environment. Features & Benefits Comes with a bag and a swivel seat mount  Light, compact, and portable Virtually unlimited angle adjustment Height adjusts from 36 to 52 in. Can be "clustered" with multiple ShadeFin Minis to cover a large area Sold separately, mounting options include a clamp mount, rod holder mount, deck mount, semi-flush mount, and side wall mount 60" x 38" coverage area  Reduces to 38" x 6" x 5" when not deployed Constructed of durable, UV-, corrosion-, and mildew-resistant materials Features powder-coated aluminum frame with injection-molded nylon components and stainless steel fasteners Fabric is high-quality WeatherMAX 3D  UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts 3-year limited warranty Specifications: Fabric Color: Black  Mount: Swivel seat  

Pro Mount Base Only For years anglers have been demanding a strong, low profile, quick release bracket for holding their fishing electronics. Designed to handle today's most popular sonar units, GPS or portable radios. The ProMount Quick Release Bracket makes it possible to easily remove your electronics weighing up to three pounds from a permanently mounted base with one hand. The 360-degree swivel adjustment lets you see the unit from any angle. The Pro Mount will fit nearly all Lowrance, Garmin, Eagle, Hummingbird, Pin-Point and Vexilar electronics. The permanent base is available separately too, which makes it easy to place several bases around the boat or even in another boat. Several systems have been mounted in trucks to hold GPS units with great success.  The ProMount sells for much less than current brackets, but with more features and versatility. The sleek, low profile of the ProMount is only 1 1/8 inches high. The permanent base has no sharp edges to step-on or wear a hole in your boat cover. An optional installation hole cover spacer comes with every base to give you a well finished look to the mount when installed. Your electronics can also be mounted overhead and hang down on the secure locking rail system of the ProMount to increase the potential places you can mount electronics. The ProMount Quick Release Bracket comes with all stainless steel mounting hardware and the bracket is corrosion resistant. The ProMount is self-draining and easy to clean, so it even looks good when the electronics are not in your boat. Features: 360-degree swivel adjustment Sleek, low profile of the ProMount is only 1-1/8 inches high Fits nearly all Lowrance, Garmin, Eagle, Hummingbird, and Vexilar electronics Made of tough ABS plastic Stainless steel mounting screws One year warranty Made in the USA Specifications: Outside Dimensions: 3.45" x 4.75" Mounting Hole Spacing: 2.3" x 3.7" Mounting Hole Size: 1/4" Supports weights up to 3 pounds One year warranty WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ProMount Quick Release Mounting Bracket For years anglers have been demanding a strong, low profile, quick release bracket for holding their fishing electronics. Designed to handle today's most popular sonar units, GPS or portable radios. The ProMount Quick Release Bracket makes it possible to easily remove your electronics weighing up to three pounds from a permanently mounted base with one hand. The 360-degree swivel adjustment lets you see the unit from any angle. The Pro Mount will fit nearly all Lowrance, Garmin, Eagle, Hummingbird, Pin-Point and Vexilar electronics. The permanent base is available separately too, which makes it easy to place several bases around the boat or even in another boat. Several systems have been mounted in trucks to hold GPS units with great success.  The ProMount sells for much less than current brackets, but with more features and versatility. The sleek, low profile of the ProMount is only 1 1/8 inches high. The permanent base has no sharp edges to step-on or wear a hole in your boat cover. An optional installation hole cover spacer comes with every base to give you a well finished look to the mount when installed. Your electronics can also be mounted overhead and hang down on the secure locking rail system of the ProMount to increase the potential places you can mount electronics. The ProMount Quick Release Bracket comes with all stainless steel mounting hardware and the bracket is corrosion resistant. The ProMount is self-draining and easy to clean, so it even looks good when the electronics are not in your boat. Features: 360-degree swivel adjustment Sleek, low profile of the ProMount is only 1 1/8 inches high Fits nearly all Lowrance, Garmin, Eagle, Hummingbird, and Vexilar electronics Made of tough ABS plastic Stainless steel mounting screws One year warranty Made in the USA Specifications: Outside Dimensions: 3.45" x 4.75" Mounting Hole Spacing: 2.3" x 3.7" Mounting Hole Size: 1/4" Supports weights up to 3 pounds One year warranty WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

964 Portable Toilet with Mounting Brackets - 2.5 Gallon - Parchment  The simple, self-contained and adult-sized SaniPottie 964 Portable Toilet provides recreational boaters with convenience and user-friendly performance.  The bellows-style flush delivers a bowl-clearing rinse every time.  Its durable, easy-to-clean construction and secure locking side latches ensure reliable long term performance.  Features: High-density polyethylene construction withstands demanding conditions Easy-to-clean, scratch-resistant finish Includes hold down brackets for permanent installation Secure-locking side latches Technical Specifications: Color - Parchment Flush Method - Manual Handle Capacity - 2.5 Gallon/9.8 L freshwater tank/2.6 gal. (9.5 l) waste tank Seat Close - Standard Weight - 12 Pounds Seat Height - 12" Material - Plastic Size - 16.5" Depth x 12.5" Height x 14.5" Wide Water Supply - Freshwater (self-contained) Discharge - Spout on bottom of tank New Item # 9108554386  WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm, and Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

964 MSD Portable Toilet with Mounting Brackets - 2.5 Gallon - Platinum The simple, self-contained and adult-sized SaniPottie 964 Portable Toilet provides recreational boaters with convenience and user-friendly performance.  The bellows-style flush delivers a bowl-clearing rinse every time.  Its durable, easy-to-clean construction and secure locking side latches ensure reliable long term performance.  Features: High-density polyethylene construction withstands demanding conditions Easy-to-clean, scratch-resistant finish Includes hold down brackets for permanent installation Secure-locking side latches Comes with Marine Sanitary Device (MSD) which allows the toilet to be plumbed for direct overboard, dockside pump-out, or remote tank discharge Technical Specifications: Color - Platinum Flush Method - Manual Handle Capacity - 2.5 Gallon/9.8 L freshwater tank/2.6 gal. (9.5 l) waste tank Seat Close - Standard Weight - 12 Pounds Seat Height - 12" Material - Plastic Size - 16.5" Depth x 12.5" Height x 14.5" Wide Water Supply - Freshwater (self-contained) Discharge - Spout on bottom of tank or MSD fitting kit  New Item # 9108554393  WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm, and Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

965 Portable Toilet with Mounting Brackets- 5 Gallon - Parchment  The simple, self-contained and adult-sized SaniPottie 965 Portable Toilet provides recreational boaters with convenience and user-friendly performance.  The bellows-style flush delivers a bowl-clearing rinse every time.  Its durable, easy-to-clean construction and secure locking side latches ensure reliable long term performance.  Features: High-density polyethylene construction withstands demanding conditions Easy-to-clean, scratch-resistant finish Includes hold down brackets for permanent installation Secure-locking side latches Technical Specifications: Color - Parchment Flush Method - Manual Handle Capacity - 3.25 Gallon/12.3 L freshwater tank/5 gal. (19.9 l) waste tank Seat Close - Standard Weight - 13.5 Pounds Seat Height - 15" Material - Plastic Size - 16.5" Depth x 15.5" Height x 14.5" Wide Water Supply - Freshwater (self-contained) Discharge - Spout on bottom of tank New Item # 9108554388  WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm, and Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

PP4800-07 PowerPod Pre-Cut for Raymarine AXIOM 9 (Pre-Cut for Surface Mount Using Rear Mounting Brackets, Requires Raymarine Right Angle Connector) PowerPods are designed for the serious boater who is blasting offshore. He demands the most from his boat and his electronics. He needs a tough and rugged mount to protect vital electronics from the harshest of offshore boating conditions. Sturdy and secure, yet clean and attractive, PowerPods are better than bracket mounting. Over 70 Pre-Cut PowerPods are available for all popular manufacturers products. 1.8" opening in the swivel tube provides plenty of room for running wires and connectors through. PowerPods are positioned at a 20 degree tilt back viewing angle. PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.