Leveler Short Hose Trim - 2-1/2" with Screws Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom. Features: 2-1/2 inches Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption Hose trim comes with four black xylon-coated screws

Long Hose Trim - 3-1/2" with Screws Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom. Features: 3-1/2 inches Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption Hose trim comes with four black xylon-coated screws

Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 400lb working pressure. Entering the transom 6" above the water line, the hoses are held securely with hose trim. Stainless steel clamps hold the hose to barb fitting at the solenoid.

Stainless Steel Short Side Door Hinge - Stamped #8 Screws Individual Bulk Packaging These Short Side Door Hinges are great for interior and exterior applications such as cabinets, hatches, folding tables, or seats where mounting space is tight. Constructed of corrosion resistant stamped 304 stainless steel. Installs with five #8 FH fasteners (not included).

Mercruiser Tilt Trim Reservoir Kit - 4 Screw Mount Tilt trim reservoir kit that will fit Arco 6275 Tilt Motor 4 screw mount. Replaces Mercruiser. Replaces: Mercruiser 883166A2 *ARCO Assurance 12-month part and labor warranty protection This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Edge Mount Trim Tab Kit w/Standard Tactile Switch Kit  - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Standard Tactile Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 12" Edge Mount Trim Tab Kit w/LED Indicator Switch Kit  - 12V  Lenco Electric Complete Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs. Lenco Trim Tab Switch Kits complete your trim tab system with totally waterproof, maintenance-free, and easy-to-install tactile switches. Kit includes:  Self-contained sealed keypad Control box 36" Pigtail Specifications: Suggested Boat Length: 17' to 30' Length of Tab: 12" Width of Tab: 12" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: LED Indicator Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 18" Super Strong Trim Tab Kit w/o Switch -24V - Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part #  15063-002 (Super Strong 24-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 24' to 40' Length of Tab: 12" Width of Tab: 18" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D or 15070-001   Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 24-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 18" Super Strong Trim Tab Kit w/o Switch -12V -Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part # 15056-002 (Super Strong 12-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 24' to 40' Length of Tab: 12" Width of Tab: 18" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 24" Super Strong Trim Tab Kit w/o Switch -24V - Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part #  15063-002 (Super Strong 24-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 27' to 44' Length of Tab: 12" Width of Tab: 24" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D or 15070-001   Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 24-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 24" Super Strong Trim Tab Kit w/o Switch -12V -Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part # 15056-002 (Super Strong 12-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 27' to 44' Length of Tab: 12" Width of Tab: 24" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 30" Super Strong Trim Tab Kit w/o Switch -24V - Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part #  15063-002 (Super Strong 24-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 30' to 48' Length of Tab: 12" Width of Tab: 30" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D or 15070-001   Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 24-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 30" Super Strong Trim Tab Kit w/o Switch -12V -Single Actuator Lenco Electric Super Strong Trim Tab Kits were designed for sport-fishing boats, high speed cruising boats and large commercial vessels. 7 Gauge flat - 304 SS blades with all stainless steel mounting hardware withstand the rigors of the most demanding conditions. No spray or mist when mounted in recessed pockets. 3/8" diameter hinge pin and 3.75" sacrificial anode. All Super Strong Trim Tab Systems have Vandar Upper Mounting Brackets with Gland Seal and 10 gauge SS lower mounting brackets with 3/8" SS bolts  Actuator Part # 15056-002 (Super Strong 12-Volt Trim Tab Kit) Specifications: Suggested Boat Length: 30' to 48' Length of Tab: 12" Width of Tab: 30" Blades: 7 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Switch Required: 10222-211D, 15069-001 or 15070-001  Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.